AVSPARE.COM
parts catalog

PLATE 3236529 - Caterpillar



3236529 PLATE Caterpillar parts PLATE
Rating:
46
Alternative (cross code) number:
CA3236529
323-6529
3236529
Caterpillar 3236529 PLATE

Buy PLATE 3236529 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:


Install plug (34) and the O-ring seal into pump body (33).
Illustration 9 g06086077
(X) equals 0.00 to 0.05 mm (0.000 to 0.002 inch).
Install shim (24) and bearing cone (23) onto shaft (38).
Install bearing cup (22) into head (19).
Install head (19) and bolts (18).
Rotate shaft (38) in order to seat the bearings. Tighten bolts (18) to a torque of 0.6 N m (5 lb in).
Take measurements at three equal intervals on the surface between head (19) and the housing. Use a feeler gauge to measure the gap between head (19) and the housing. The average of the three measurements should be Dimension (X).
Grind or replace shim (24) to achieve Dimension (X).
Remove bolts (18), head (19), bearing cone (23), and shim (24).
Illustration 10 g06086063
Illustration 11 g06086061
Improper assembly of parts that are spring loaded can cause bodily injury.To prevent possible injury, follow the established assembly procedure and wear protective equipment.
Install washer (31), spring (32), and pins (30) into barrel assembly (25).
Use a suitable press, Tooling (B), and a washer to install retaining ring (29) into barrel assembly (25).
Illustration 12 g06086060
Install bearing (28), plate (27), and pistons (26) onto barrel assembly (25).
Illustration 13 g06086059
Rotate Tooling (A) and install barrel assembly (25).
Install shim (24) that was determined in Step 17.
Illustration 14 g06086057
Install bearing cone (23).
Illustration 15 g06086078
Apply Tooling (D) onto the back side of port plate (21). Install port plate (21) and O-ring seal (20) onto head (19).
Illustration 16 g06086055
Improper assembly of parts that are spring loaded can cause bodily injury.To prevent possible injury, follow the established assembly procedure and wear protective equipment.
Install head (19) and bolts (18). Tighten bolts (18) to a torque of 170 N m (125 lb ft).
Illustration 17 g06085402
Improper assembly of parts that are spring loaded can cause bodily injury.To prevent possible injury, follow the established assembly procedure and wear protective equipment.
Install O-ring seal (14), O-ring seal (15), thrust ring (16), and housing (17) into valve (4).
Install O-ring seal (7), O-ring seal (8), thrust ring (9), and housing (10) into valve (4).
Install O-ring seal (6), (12), plug (5), and (11).
Install gasket (13).
Illustration 18 g06086054
Install valve (4) and bolts (3). Tighten bolts (3) to a torque of 11 2 N m (94 17 lb in).
Illustration 19 g06085815
Install O-ring seal (1) and coupler (2).
Remove the piston pump from Tooling (A) or suitable fixture.End By:
Install the piston pump (Steering).


Parts plate Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.