3377050 PLATE Caterpillar parts
Rating:
Alternative (cross code) number:
CA3377050
337-7050
3377050
CA3377050
337-7050
3377050
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$70.79
31 Aug 2023
2.2046[0.99] Pounds
Amazon.com
Halder USA - Supercraft Dead Blow (3377.05), White
Halder Non-rebound, for extra powerful strikes. Noise-dampening and gentle on the joints. || Inserts made of special nylon with maximum strength. Break-proof steel tube handle with ergonomic non-slip rubber grip. || Completely robot-welded. Handle protection sleeve acts as an overstrike protector. || Handle and inserts replaceable. || Wear-resistant powder coating prevents corrosion. Available in sizes of D25mm to D70mm.
Halder Non-rebound, for extra powerful strikes. Noise-dampening and gentle on the joints. || Inserts made of special nylon with maximum strength. Break-proof steel tube handle with ergonomic non-slip rubber grip. || Completely robot-welded. Handle protection sleeve acts as an overstrike protector. || Handle and inserts replaceable. || Wear-resistant powder coating prevents corrosion. Available in sizes of D25mm to D70mm.
For full view, you need register
Information:
Installation Procedure
Table 1
Required Parts
Item Pt. No. Description Qty
1 7S-8920 Clip 1
2 7S-8921 Clip 1
3 4L-6454 Bolt 2
4 6V-8801 Nut 1
5 5P-1075 Hard Washer 3
6 9N-1909 Bracket 1
7 8D-3508 Boss 1
Illustration 1 g01065116
Weld (W1) is a 3.0 mm (0.12 inch) fillet weld.
Bend bracket (6) so that the angle of the bracket is approximately 99 degrees. This will allow the bottom of boss (7) to align with the top of the frame rail.
Install clip (1) and clip (2) on the filler tube.
Connect clips (1) and (2) to bracket (6) with bolt (3), washers (5) and nut (4) .
Connect boss (7) to bracket (6) with bolt (3) and washer (5) .
Weld boss (7) to the frame rail with a 3.0 mm (0.12 inch) fillet weld (W1) around the entire circumference.
Table 1
Required Parts
Item Pt. No. Description Qty
1 7S-8920 Clip 1
2 7S-8921 Clip 1
3 4L-6454 Bolt 2
4 6V-8801 Nut 1
5 5P-1075 Hard Washer 3
6 9N-1909 Bracket 1
7 8D-3508 Boss 1
Illustration 1 g01065116
Weld (W1) is a 3.0 mm (0.12 inch) fillet weld.
Bend bracket (6) so that the angle of the bracket is approximately 99 degrees. This will allow the bottom of boss (7) to align with the top of the frame rail.
Install clip (1) and clip (2) on the filler tube.
Connect clips (1) and (2) to bracket (6) with bolt (3), washers (5) and nut (4) .
Connect boss (7) to bracket (6) with bolt (3) and washer (5) .
Weld boss (7) to the frame rail with a 3.0 mm (0.12 inch) fillet weld (W1) around the entire circumference.
Parts plate Caterpillar catalog:
3376833
PLATE
Caterpillar
Caterpillar
3376749
PLATE
Caterpillar
Caterpillar
3376500
PLATE
Caterpillar
Caterpillar
3376463
PLATE
Caterpillar
Caterpillar
3376440
PLATE
Caterpillar
Caterpillar
3376340
PLATE
Caterpillar
Caterpillar
3380553
PLATE-WEAR
Caterpillar
Caterpillar
3380497
PLATE
Caterpillar
Caterpillar
3380058
PLATE
Caterpillar
Caterpillar
3378177
PLATE
Caterpillar
Caterpillar
3377614
PLATE
Caterpillar
Caterpillar
3377179
PLATE
Caterpillar
Caterpillar