AVSPARE.COM
parts catalog

PLATE 3727838 - Caterpillar



3727838 PLATE Caterpillar parts 980K, 980K HLG, 986H PLATE
Rating:
36
Alternative (cross code) number:
CA3727838
372-7838
3727838
Caterpillar 3727838 PLATE
Weight: 0.31 pounds 0 kg.

Buy PLATE 3727838 Caterpillar genuine, new aftermarket tractor parts with delivery
WHEEL LOADER,

Compatible equipment models: 3727838:

WHEEL LOADER  980K   980K HLG   986H   Caterpillar
Number on catalog scheme: 16
 
  For full view, you need register

Information:

Leakage Around Oil Filter Seal
Naturally-aspirated 3208 Engines, at times, have oil leakage past the oil filter seal at start-up during cold weather. Analysis of this problem has shown several possible causes.
... Damaged filter base. The contact surface for the oil filter seal is damaged so that an acceptable seal between the filter and base is not possible.
... No lubrication on filter seal. If too little or no lubricant was put on the oil filter seal before it was installed, the seal was probably damaged during installation of the oil filter. Identification of this type of damage can be made by inspection of the seal. Look for stretch marks and/or a rippled (not smooth) seal surface.
... Damaged or incorrectly (not correct) installed seals. Before an oil filter is installed, carefully inspect the seal to make sure that it is correctly installed and not damaged.
... Oil filter not tightened correctly. To correctly install the filter after lubricant has been put on the seal, clean the filter base and tighten the filter by hand until the seal makes contact with the base. With a filter wrench, tighten the filter an added 3/4 turn.
... Incorrect lubricant viscosity. Use of the wrong lubricant for the ambient (outside) temperature range can cause higher lubrication system pressures. See the correct Operation Guide for the correct oil type and grade.
... Incorrect start-up procedure during cold weather. When an engine is first started in cold weather, it must be operated for at least five minutes at low idle with no load before its speed is increased and a load is added.
The 2W4110 Relief Valve Guide and the 1W3852 Shield can be installed when the oil pan is removed for any type of service. If desired, the earlier 1W1789 Relief Valve Guide can be installed with the 1W3852 Shield if modifications are made to the guide.
To make the modification, use a 6.00 mm (.236") diameter bit to drill out the three holes farthest from the threads. Remove all burrs from the passages on both the inside and the outside of the guide; burrs can prevent free operation of the relief valve.
Do not use the 1W3852 Shield with a 1W1789 Relief Valve Guide that has not had modifications.
Illustration 1. Location of the relief valve guide.
Illustration 2. Location of the three holes that need to be made larger.

Caterpillar parts catalog:

Caterpillar parts catalog
980K Wheel Loader W7K00001-UP (MACHINE) POWERED BY C13 Engine
980K Wheel Loader GTZ00001-UP (MACHINE) POWERED BY C13 Engine
986H Wheel Loader L8S00001-UP (MACHINE) POWERED BY C15 Engine
980K Wheel Loader High Lift Grapple NEP00001-UP (MACHINE) POWERED BY C13 Engine


Parts plate Caterpillar catalog:

3445539 PLATE
980K, 980K HLG, 980M, 982M
3445538 PLATE
980K, 980K HLG, 980M, 982M
3545867 PLATE
980K, 980K HLG, 980M
3544777 PLATE
980K, 980K HLG
3704568 PLATE
980K, 980K HLG, 980M, 982M
3704567 PLATE
980K, 980K HLG, 980M, 982M
3720673 PLATE
980K, 980K HLG, 980M, 986H, R3000H
3703812 PLATE
824K, 825K, 826K, 980K, 980K HLG, 980M, 982M, 986H, R3000H
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.