AVSPARE.COM
parts catalog

PLATE 3727908 - Caterpillar



3727908 PLATE Caterpillar parts 521B, 522B, 541 2, 552 2 PLATE
Rating:
79
Alternative (cross code) number:
CA3727908
372-7908
3727908
Caterpillar 3727908 PLATE

Buy PLATE 3727908 Caterpillar genuine, new aftermarket tractor parts with delivery
TRACK FELLER BUNCHER,

Compatible equipment models: 3727908:

TRACK FELLER BUNCHER  521B   522B   541 2   552 2   Caterpillar
Number on catalog scheme: 4
 
  For full view, you need register

Information:


Illustration 1 g06016284
Simplified Schematic for CID 1674 (Solenoid Return #1)
This diagnostic code is associated with the "Solenoid Return #1" circuit. FMI 04 indicates that the Brake ECM has determined that the voltage in the return circuit for the Automatic Retarder Control (ARC) solenoid is below normal.For more information on the ARC solenoids, refer to Systems Operation, "Electrical Output Components" in this manual.Conditions that could cause this diagnostic code to be activated are listed below:
The return circuit for one or both solenoids are shorted to a ground source.
The ECM has failed. ECM failure is unlikely.Note: Before performing this procedure, inspect the harness connectors that are involved in the circuit. Poor connections can often be the cause of a problem in an electrical circuit. Verify that all connections in the circuit are clean, secure and in good condition. If a problem with a connection is found, correct the problem and verify that this diagnostic code is active before performing this procedure.Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear these diagnostic codes when the original diagnostic code has been corrected.Test Step 1. CHECK THE "SOLENOID 1 RETURN" CIRCUIT FOR A SHORT TO GROUND
Turn the key start switch and the disconnect switch to the OFF position.
Disconnect all the solenoids shown in the schematic above.
Disconnect the J1 and J2 harness connectors from the Brake ECM.
At the machine harness connectors for the ECM, measure the resistance from the "Solenoid Return #1" contact J1-54 (wire J815-BK(Black)) and the frame ground location. Measure the resistance from the contact J1-54 (wire J815-BK(Black)) and all other J1 and J2 contacts that are used in the Brake ECM.Expected Result:Each resistance measurement is greater than 50 ohms.Results:
OK - Each resistance measurement is greater than 50 ohms. The measurement is not indicating that the "solenoid 1 return" circuit is shorted to a ground source. Proceed to Test Step 2.
NOT OK - One or more of the resistance measurements are less than 50 ohms. There is a short in the machine harness. The short is between wire J815-BK(Black)and the circuit with the low-resistance measurement or frame ground.Repair: For information on testing for short circuits and finding short circuits, refer to Testing and Adjusting, "Wiring Harness (Short Circuit) - Test" in this manual.
Repair or replace the machine harness.STOPTest Step 2. CHECK THE STATUS OF THE DIAGNOSTIC CODEReference:
Testing and Adjusting, "Electrical Connector - Inspect"
Inspect the harness connectors. Clean the contacts of the harness connectors. Check the wires for damage to the insulation that is caused by excessive heat, battery acid, or chafing.
Perform a 45 N (10 lb) pull test on each of the wires that are associated with the sensor circuit.
Reconnect all harness connectors. Make sure that the connectors are fully seated. Observe that the clips for each connector are fastened securely.
Turn the disconnect switch and the key start switch to the ON position.
Operate the machine.
Check the status of the CID 1674 FMI 04 diagnostic code.Expected Result:The CID 1674 FMI 04 diagnostic code is not active.Results:
OK

Caterpillar parts catalog:

Caterpillar parts catalog
541 Series 2 Track Feller Buncher F7D00001-UP (MACHINE) POWERED BY C9 Engine
521B TRACK FELLER BUNCHER F7B00001-UP (MACHINE) POWERED BY C9 Engine
522B TRACK FELLER BUNCHER F7C00001-UP (MACHINE) POWERED BY C9 Engine
552 Series 2 Track Feller Buncher F7G00001-UP (MACHINE)


Parts plate Caterpillar catalog:

3T9525 PLATE AS-BRUSH
1090, 1190, 1190T, 120M, 120M 2, 1290T, 12M 2, 12M 3, 12M 3 AWD, 1390, 140M, 140M 2, 140M 3, 140M 3 AWD, 14H, 14M, 160M, 160M 2, 160M 3, 160M 3 AWD, 16H NA, 16M, 2290, 235, 235D, 2390, 2391, 245, 2491...
2463150 PLATE-THRUST
12H, 12M 2, 12M 3, 12M 3 AWD, 140M, 140M 2, 140M 3, 140M 3 AWD, 160M, 160M 2, 160M 3, 160M 3 AWD, 2290, 2390, 2391, 2491, 2590, 2864C, 330C, 330C FM, 330C L, 330C MH, 330D, 330D FM, 330D L, 330D LN, 3...
1676701 PLATE-RETAINING
1090, 1190, 1190T, 1290T, 1390, 2290, 2390, 2391, 2491, 2590, 320B, 321B, 322B L, 322C, 322C FM, 324D FM, 324D FM LL, 325B, 325B L, 325C FM, 325D FM, 325D FM LL, 330B L, 330C FM, 330C L, 330D FM, 330D...
2531346 PLATE-WARNING
1290T, 1390, 2491, 2590, 307C, 307D, 307E, 308C, 308D, 308E, 308E CR, 308E SR, 308E2 CR, 311D LRR, 311F LRR, 312C, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313D, 313D2, 313D2 LGP, 314D CR...
1884173 PLATE-SEPARATOR
1090, 1190, 1190T, 1290T, 1390, 2290, 2390, 2391, 2491, 2590, 322C, 322C FM, 324D, 324D FM, 324D FM LL, 324D L, 324D LN, 324E, 324E L, 324E LN, 325C, 325C FM, 325D, 325D FM, 325D FM LL, 325D L, 325D M...
2042677 PLATE-VALVE
1090, 1190, 1190T, 1290T, 1390, 2290, 2390, 2391, 2491, 2590, 322C, 322C FM, 324D, 324D FM, 324D FM LL, 324D L, 324D LN, 324E, 324E L, 324E LN, 325C, 325C FM, 325D, 325D FM, 325D FM LL, 325D L, 325D M...
1948261 PLATE-VALVE
1090, 1190, 1190T, 1290T, 1390, 2290, 2390, 2391, 2491, 2590, 330C, 330C FM, 330C L, 330C MH, 345B II, 345B II MH, 511, 521, 521B, 522, 522B, 532, 541, 541 2, 551, 552, 552 2, TK1051, TK711, TK721, TK...
1772491 PLATE
1090, 1190, 1190T, 1290T, 1390, 2290, 2390, 2391, 2491, 2590, 330C, 330C FM, 330C L, 330C MH, 345B II, 345B II MH, 511, 521, 521B, 522, 522B, 532, 541, 541 2, 551, 552, 552 2, TK1051, TK711, TK721, TK...
1772497 PLATE
1090, 1190, 1190T, 1290T, 1390, 2290, 2390, 2391, 2491, 2590, 330C, 330C FM, 330C L, 330C MH, 345B II, 345B II MH, 511, 521, 521B, 522, 522B, 532, 541, 541 2, 551, 552, 552 2, TK1051, TK711, TK721, TK...
3722537 PLATE
521B, 522B, 541 2, 552 2
3744432 PLATE
521B, 522B, 541 2, 552 2
3724552 PLATE
521B, 522B, 541 2, 552 2
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.