AVSPARE.COM
parts catalog

PLATE-CLAMP 3728238 - Caterpillar



3728238 PLATE-CLAMP Caterpillar parts C15, C27 PLATE
Rating:
46
Alternative (cross code) number:
CA3728238
372-8238
3728238
Caterpillar 3728238 PLATE-CLAMP

Buy PLATE-CLAMP 3728238 Caterpillar genuine, new aftermarket tractor parts with delivery
GENERATOR SET,

Compatible equipment models: 3728238:

GENERATOR SET  C15   C27   Caterpillar
Number on catalog scheme: 13
 
  For full view, you need register

Information:

Which Generate This Code:This diagnostic code is recorded when the second output driver in the MSS ECM is shorted to ground. This circuit is not used on all machines. Check for the presence of wires at contact 5 and contact 52 before you perform the procedure.The possible causes of this diagnostic code are listed below:
The wiring in the machine harness has failed.
The driven component in the circuit has failed.
The ECM has failed. This is unlikely.Test Step 1. CHECK THE WIRING HARNESS.
Disconnect the wiring harness connector from the MSS ECM.
Measure the resistance between pin 18 in the wiring harness and a ground on the machine.Expected Result:The resistance is greater than 5000 Ohms.Results:
YES - The resistance is greater than 5000 Ohms (no continuity). Harness circuit resistance is correct. Proceed to Test Step 3.
NO - Resistance is less than 5000 Ohms (continuity). The machine harness is faulty. There is a short between frame ground and the machine harness. The driven component in the circuit may also be bad. Proceed to Test Step 2.Test Step 2. CHECK THE COMPONENT.
Trace the harness to the driven component in the circuit. The component will be a relay. The component may also be a solenoid.
Measure the resistance of the component. Measure the resistance from each terminal to the case of the component.Expected Result:The resistance is greater than 5000 Ohms.Results:
YES - The resistance of the driven component is greater than 5000 Ohms (no continuity). The component is good. The machine harness has failed. There is a short between frame ground and the machine harness.Repair: Check the harness for signs of damage. Repair the machine harness or replace the machine harness. Stop.
NO - Resistance is less than 5000 Ohms (continuity). The driven component has failed. Repair: Replace the component that has failed. Stop.Test Step 3. CHECK IF THE DIAGNOSTIC CODE IS STILL ACTIVE.
Remove the connector from the ECM. Inspect the contacts and clean the contacts of the harness connectors.
Reconnect all harness connectors.
Turn the key start switch to the ON position.
Clear all inactive diagnostic codes.
Operate the machine.
Determine if CID 1392 FMI 04 is present.Expected Result:CID 1392 FMI 04 is present.Results:
YES - CID 1392 FMI 04 is present.Repair: The problem has not been corrected. It is unlikely that the ECM has failed. Perform the previous Steps again. If the cause of the diagnostic code is not found, replace the ECM. See Testing and Adjusting, "Electronic Control Module (ECM) - Replace". Stop.
NO - CID 1392 FMI 04 is not present.Repair: The diagnostic code is NOT present. The problem does not exist at this time. The initial problem was probably caused by an intermittent short in the wiring harness. Inspect the harness for any signs of damage. If the harness passes through a hole with a grommet, that area of the harness can become chafed. This may cause an intermittent short. The harness may also be damaged in locations that could pinch the harness. Repair any wiring that could have caused the problem. Resume normal machine operation. Stop.

Caterpillar parts catalog:

Caterpillar parts catalog
XQ500 Power System GG500001-UP POWERED BY C15 Engine
C15 Rental Generator Set X5M00001-UP POWERED BY C15 Engine
C27 Rental Generator Set N1B00001-UP
XG400 CG137–12 Power Module AL500001-UP


Parts plate Caterpillar catalog:

3T9525 PLATE AS-BRUSH
1090, 1190, 1190T, 120M, 120M 2, 1290T, 12M 2, 12M 3, 12M 3 AWD, 1390, 140M, 140M 2, 140M 3, 140M 3 AWD, 14H, 14M, 160M, 160M 2, 160M 3, 160M 3 AWD, 16H NA, 16M, 2290, 235, 235D, 2390, 2391, 245, 2491...
9R8760 PLATE
24H, 24M, 416B, 416C, 416D, 420D, 424B, 424B HD, 424D, 426B, 426C, 428B, 428C, 428D, 430D, 432D, 436C, 438C, 438D, 442D, 980G, 980G II, 980H, 980K, 980K HLG, C15, C15 I6, C18 I6, C9
2531752 PLATE-THRUST
16G, 16H NA, 24H, 24M, 3406, 3406B, 3406C, 3406E, 3408, 3408B, 3408C, 3408E, 3412, 3412C, 3412D, 3412E, 3456, 365C, 365C L, 365C L MH, 374D L, 374F L, 375, 375 L, 385B, 385C, 385C FS, 385C L, 385C L M...
6I4421 PLATE-SPACER
24M, 3406E, 3456, 365C, 365C L, 365C L MH, 374D L, 374F L, 385B, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 390F L, 5090B, 583T, 587T, 621B, 621G, 623G, 627F, 627G, 631D, 631E, 631G, 633E II, 637...
1129217 PLATE-THRUST
16G, 16H NA, 24H, 24M, 3406, 3406B, 3406C, 3406E, 3408, 3408B, 3408C, 3408E, 3412, 3412C, 3412D, 3412E, 3456, 365C, 365C L, 365C L MH, 374D L, 374F L, 375, 375 L, 385B, 385C, 385C FS, 385C L, 385C L M...
1591533 PLATE-SEALING
24M, 3406E, 3456, 365C, 365C L, 365C L MH, 374D L, 374F L, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 390F L, 583T, 587T, 621B, 621G, 623G, 627F, 627G, 631D, 631E, 631G, 633E II, 637D, 637E, 637G...
4N0342 PLATE-CAMSHAFT THRUST
16G, 16H NA, 245, 245D, 24H, 3406, 3406B, 3406C, 3408, 3408B, 3408C, 3408E, 3412, 3412C, 3412D, 3412E, 375, 375 L, 5080, 5110B, 578, 583R, 587R, 589, 621E, 621F, 623E, 623F, 627B, 627E, 627F, 631D, 63...
2253100 PLATE-SPACER
24H, 3412, 3412C, 3412D, 3412E, 5110B, 651E, 657E, 773B, 773D, 773E, 773F, 773G, 773G LRC, 773G OEM, 775B, 775D, 775E, 775F, 775G, 775G LRC, 775G OEM, 777C, 777D, 777F, 777G, 844, 844H, 844K, 854K, 99...
1210169 PLATE-INFORMATION
140M 2, 3126, 3126B, 3126E, C-10, C15, C18, CX31-C18I, CX35-C18I, R2900G, SCT673
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.