3845560 PLATE-HOOK Caterpillar parts
950 GC, 950H, 950K, 962H, 962K
Rating:
Alternative (cross code) number:
CA3845560
384-5560
3845560
CA3845560
384-5560
3845560
WHEEL LOADER,
Number on catalog scheme:
5
For full view, you need register
Information:
This diagnostic code is associated with the Left Joystick at the Forward-Rearward location for the Position Sensor. The position sensor provides a PWM input signal to the Machine ECM. The FMI 13 diagnostic code is activated when the ECM detects that the sensor needs to be calibrated.The possible causes of this diagnostic code are listed:
The ECM has been replaced or new software has been installed.
The calibration procedure has failed.Note: The sensor does not connect directly to the frame ground. The sensor connects to the return circuit of the ECM. The ECM internally connects the return wire to frame ground. In order to correct this diagnostic code, calibrate the sensor.Test Step 1. Calibration
Perform the calibration procedure for the sensor. Refer to Testing and Adjusting, "Calibration" section of this manual for the correct calibration procedure. Verify that the calibration procedure for the ECM has been successfully completed. The calibration must complete without warnings in order to clear the FMI 13.
Observe the status of the CID 2474 FMI 13. Expected Result:The calibration procedure was performed successfully.CID 2474 FMI 13 has been clearedResults:
YES - The calibration procedure was performed successfully. Resume normal machine operation.STOP
NO - The calibration was not successful.Repair: Repeat the calibration procedure for the sensor.If the second calibration procedure is not successful, replace the Joystick assembly. After Joystick replacement, refer to Testing and Adjusting, "Calibration" section of this manual for the correct calibration procedure. If the problem is still present after replacement and calibration of the new joystick, the ECM may have failed.Prior to replacing an ECM, always contact your Dealer Technical Communicator for possible consultation with Caterpillar. This consultation may greatly reduce repair time. If the cause of the diagnostic code is not found, replace the ECM. Refer to Testing and Adjusting, "Electronic Control Module (ECM) - Replace".STOP
The ECM has been replaced or new software has been installed.
The calibration procedure has failed.Note: The sensor does not connect directly to the frame ground. The sensor connects to the return circuit of the ECM. The ECM internally connects the return wire to frame ground. In order to correct this diagnostic code, calibrate the sensor.Test Step 1. Calibration
Perform the calibration procedure for the sensor. Refer to Testing and Adjusting, "Calibration" section of this manual for the correct calibration procedure. Verify that the calibration procedure for the ECM has been successfully completed. The calibration must complete without warnings in order to clear the FMI 13.
Observe the status of the CID 2474 FMI 13. Expected Result:The calibration procedure was performed successfully.CID 2474 FMI 13 has been clearedResults:
YES - The calibration procedure was performed successfully. Resume normal machine operation.STOP
NO - The calibration was not successful.Repair: Repeat the calibration procedure for the sensor.If the second calibration procedure is not successful, replace the Joystick assembly. After Joystick replacement, refer to Testing and Adjusting, "Calibration" section of this manual for the correct calibration procedure. If the problem is still present after replacement and calibration of the new joystick, the ECM may have failed.Prior to replacing an ECM, always contact your Dealer Technical Communicator for possible consultation with Caterpillar. This consultation may greatly reduce repair time. If the cause of the diagnostic code is not found, replace the ECM. Refer to Testing and Adjusting, "Electronic Control Module (ECM) - Replace".STOP
Caterpillar parts catalog:
Parts plate Caterpillar catalog:
120H, 120H ES, 120H NA, 120K, 120K 2, 12H, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 135H, 135H NA, 140G, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 160K, 160M, 160M 2, 160M 3, 160M 3 AWD, 2290, 2390, 2...
120G, 12F, 12G, 130G, 140, 141, 14E, 14G, 153, 16, 163, 16G, 172, 173B, 183, 183B, 184, 191, 193, 30/30, 416, 416B, 426B, 428, 428B, 438B, 446, 46, 508, 515, 517, 518, 525, 525D, 527, 528, 535D, 545D,...
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 12H, 12K, 135H, 135H NA, 140H, 140K, 140K 2, 160H, 160K, 446B, 5130, 5130B, 515, 5230B, 525, 525B, 525C, 535B, 535C, 950G, 950G II, 950H, 950K, 962G, 962G I...
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 12H, 12K, 135H, 135H NA, 140H, 140K, 140K 2, 160H, 160K, 446B, 446D, 5130, 5130B, 515, 5230B, 525, 525B, 525C, 535B, 535C, 545, 545C, 950G, 950G II, 950H, 9...
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 12E, 12G, 12H, 12H ES, 12H NA, 12K, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 14H, 14H NA, 160G, 160H, 160H ES, 160H NA, 160K, ...
65, 65C, 65E, 75, 75C, 75D, 75E, 85C, 85D, 85E, 950F II, 950G, 950G II, 950H, 95E, 960F, 962G, 962G II, 962H, 966C, 966H, 966K, IT62G, IT62G II, R1300G II
3512B, 3516B, 3516C, 587T, 814B, 814F, 815B, 815F, 816F, 950F II, 950G, 950G II, 950H, 950K, 960F, 962G, 962G II, 962H, 962K, 966D, 966F, 966F II, 966G, 966G II, 966H, 966K, 966M, 966M XE, 970F, 972G,...
950G, 950G II, 950H, 950K, 962G, 962G II, 962H, 962K, 966F II, 966G, 966G II, 966H, 966K, 966M, 966M XE, 972G, 972G II, 972H, 972K, 972M, 972M XE, 973C, 973D, 980K
2470C, 2570C, 2670C, 2864C, 533, 543, 553C, 563C, 573C, 586C, 814F, 814F II, 924K, 930K, 936F, 938F, 938G, 938G II, 950F, 950F II, 950G, 950G II, 950H, 950K, 960F, 962G, 962G II, 962H, 962K, 966F, 966...
120H, 120M, 12H, 12M, 135H, 140H, 140M, 143H, 14H, 14M, 160H, 160M, 163H, 16H, 651E, 657E, 657G, 938G II, 938H, 950G II, 950H, 962G II, 962H, IT38G II, IT38H, IT62G II, IT62H, RM-300, RM-500
16, 525B, 525C, 535B, 535C, 545, 545C, 611, 613G, 615, 615C, 772, 814B, 814F, 814F II, 815B, 815F, 815F II, 816F, 816F II, 824C, 824G, 824G II, 824H, 824K, 825G, 825G II, 825H, 825K, 826C, 826G, 826G ...
320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D2, 320D2 GC, 320D2 L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 322C, 322C FM, 323D L, 323D2 L, 323E L, 324D, 324D FM, 324D FM LL, 324D L, 324D LN, 324E...
3845559
PLATE-WEAR
950 GC, 950H, 950K, 962H, 962K
950 GC, 950H, 950K, 962H, 962K
3845557
PLATE AS-SIDE
950 GC, 950H, 950K, 962H, 962K
950 GC, 950H, 950K, 962H, 962K
3845574
PLATE-WEAR
950 GC, 950H, 950K, 962H, 962K
950 GC, 950H, 950K, 962H, 962K
3845573
PLATE-SIDE BAR
950 GC, 950H, 950K, 962H, 962K
950 GC, 950H, 950K, 962H, 962K
3845556
PLATE AS-SIDE
950 GC, 950H, 950K, 962H, 962K
950 GC, 950H, 950K, 962H, 962K
2618623
PLATE
950H, 962H
950H, 962H
3845583
PLATE-WEAR
950 GC, 950H, 950K, 962H, 962K
950 GC, 950H, 950K, 962H, 962K
3845580
PLATE AS-SIDE
950 GC, 950H, 950K, 962H, 962K
950 GC, 950H, 950K, 962H, 962K
3845589
PLATE-WEAR
950 GC, 950H, 950K, 962H, 962K
950 GC, 950H, 950K, 962H, 962K
3845588
PLATE-SIDE BAR
950 GC, 950H, 950K, 962H, 962K
950 GC, 950H, 950K, 962H, 962K
3845579
PLATE AS-SIDE
950 GC, 950H, 950K, 962H, 962K
950 GC, 950H, 950K, 962H, 962K
3845568
PLATE-WEAR
950 GC, 950H, 950K, 962H, 962K
950 GC, 950H, 950K, 962H, 962K