AVSPARE.COM
parts catalog

PLATE & FILM GP 3904952 - Caterpillar



3904952 PLATE & FILM GP Caterpillar parts SE60 V XW PLATE
Rating:
59
Alternative (cross code) number:
CA3904952
390-4952
3904952
Caterpillar 3904952 PLATE & FILM GP

Buy PLATE & FILM GP 3904952 Caterpillar genuine, new aftermarket tractor parts with delivery
ASPHALT SCREED,

Compatible equipment models: 3904952:

ASPHALT SCREED  SE60 V XW   Caterpillar
Number on catalog scheme:
 
  For full view, you need register

Information:

Start By:a. remove oil pump1. Check the connecting rods and caps for their identification and location. 2. Turn the crankshaft until the connecting rod caps are in position.3. Remove two bolts (1) and the cap from the connecting rod. Remove the lower half of the bearing from the cap.4. Push the connecting rod away from the crankshaft. Remove the upper half of the bearing from the connecting rod. Install the bearings dry when the clearance checks are made. Put clean engine oil on the bearings for final assembly.5. Install the upper half of the bearing in the connecting rod.6. Pull the connecting rod slowly on to the crankshaft.7. Install the lower half of the bearing in the cap.
Be sure the tabs in the back of bearings are in the tab grooves of the connecting rod and cap. The serviceman must be very careful to use Plastigage, Tool (A) correctly. The following points must be remembered.
... Make sure that the backs of the bearings and the bores are clean and dry.... Make sure that the bearing locking tabs are properly seated in their slots.... The crankshaft must be free of oil where the Plastigage touches it.... Put a piece of Plastigage (A) on the crown of the bearing half that is in the cap. Do not allow the Plastigage to extend over the edge of the bearing.... Install the bearing cap using the correct torque-turn specifications. Do not use an impact wrench. Be careful not to dislodge the bearing when the cap is installed.... Do not turn the crankshaft with the Plastigage installed.... Carefully remove the cap but do not remove the Plastigage. Measure the width of the Plastigage while it is in the bearing cap or on the crankshaft journal. Do this by using the correct scale on the package. Record the measurements.... Remove the Plastigage before reinstalling the cap.When using Plastigage, the readings can sometimes be unclear. For example, all parts of the Platigage are not the same width. Measure the major widths to make sure that they are within the specification range. Also, experience has shown that when checking clearances tighter than 0.10 mm (.004 in)the readings may be low by 0.013 to 0.025 mm (.0005 to .0010 in).Out-of-round journals can give faulty readings. Also, journal taper may be indicated when one end of the Plastigage is wider than the other.For complete details concerning measuring bearing clearances. See Engine Bearings & Crankshafts, SEBD0531. 8. Use Plastigage (A) to check the bearing clearance.9. Put Plastigage (A) on the bearing.10. Put 2P-2506 Thread Lubricanton the threads of the rod bolts and seat surfaces of the nuts. Be sure the cylinder numbers on the rod cap and rod are the same and are on the same side of connecting rod. Numbers are on the same side of the rod and cap as are the bearing tab slots. If new rods are installed, put the cylinder number on the rod and cap. Do not turn the crankshaft when Plastigage (A)

Caterpillar SIS machinery equipment:

Caterpillar SIS

Caterpillar parts catalog:

Caterpillar parts catalog
AP1055 F Asphalt Paver TJ500001-UP (MACHINE) POWERED BY C7.1 Engine
AP1000 F Asphalt Paver AC400001-UP (MACHINE) POWERED BY C7.1 Engine
AP1055 F Asphalt Paver RLM00001-UP (MACHINE) POWERED BY C7.1 Engine
AP655F & AP600F Asphalt Paver 65500001-UP (MACHINE) POWERED BY C4.4 Engine
AP600F, AP655F Asphalt Paver LR600001-UP (MACHINE) POWERED BY C7.1 Engine


Parts plate Caterpillar catalog:

7R7954 PLATE
AP-1000, AP-1055D, AP-600D, AP-655C, AP-800, AP-800C, AP-800D, AP1055E, AP555E, AS3251C, AS3301C, BG-225B, BG-2455D, BG1055E, BG500E, BG600D, CB-334D, CB-334E, CB-335D, CB-534B, CB-534C, CB-534D, CB-5...
1028706 PLATE AS
AP-1055B, AP-1055D, AP-600D, AP-655C, AP-655D, AP555E, AS4173, AS4251C, AS4252C, BG-2455D, BG-260D, BG1000E, BG1055E, CB-434D, CB-534D, CB-54, CB-54B, CB-564D, CB-634D, CB-64, CD-54, CP-44, CP-54B, CP...
7X0993 PLATE GP-SOUND SUPPRESSION
245B, 245D, 428, 438, D3C, D6H, D6H XL, D6H XR
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.