AVSPARE.COM
parts catalog

PLATE-SIDE BAR 3967033 - Caterpillar



3967033 PLATE-SIDE BAR Caterpillar parts 980H, 980K PLATE
Rating:
14
Alternative (cross code) number:
CA3967033
396-7033
3967033
Caterpillar 3967033 PLATE-SIDE BAR

Buy PLATE-SIDE BAR 3967033 Caterpillar genuine, new aftermarket tractor parts with delivery
WHEEL LOADER,

Compatible equipment models: 3967033:

WHEEL LOADER  980H   980K   Caterpillar
Number on catalog scheme:
 
  For full view, you need register

Information:


Table 1
Diagnostic Trouble Codes for the Start Relay
J1939 Code CDL Code Code Description
(code descriptions may vary) Comments
677-5 444-5 Starter Motor Relay : Current Below Normal The Electronic Control Module (ECM) detects a low current condition (open circuit) in the start relay control circuit.
677-6 444-6 Starter Motor Relay : Current Above Normal The Electronic Control Module (ECM) detects a high current condition (short circuit) in the start relay control circuit.
Follow the troubleshooting procedure to identify the root cause of the fault. During the following procedure, refer to the electrical schematic for the application.Complete the procedure in the order in which the steps are listed.
Table 2
Troubleshooting Test Steps Values Results
1. Inspect Electrical Connectors and Wiring
A. Check that the fuses are not blown.
B. Inspect the terminals on the start relay. Refer to Troubleshooting, "Electrical Connector - Inspect" for details.
C. Perform a 45 N (10 lb) pull test on each of the start relay wires in the ECM connector.
D. Check the screw for the ECM connector for the correct torque of 6 N m (53 lb in).
E. Check the harness for abrasion and pinch points from the start relay back to the ECM.
Loose connection or damaged wire
Result: There is a fault in a connector or the wiring.
Repair: Repair any faulty connectors or replace the wiring harness. Ensure that all the seals are properly in place and ensure that the connectors are correctly coupled.
Replace any blown fuses.
Use the electronic service tool to clear all logged diagnostic codes and verify that the repair eliminates the fault.
Result: All connectors, pins, and sockets are correctly coupled and/or inserted. The harness is free of corrosion, abrasion, and pinch points. The fuses are not blown.
Proceed to Test Step 2.
2. Check for Active Diagnostic Codes
A. Connect the electronic service tool to the diagnostic connector.
B. Turn the keyswitch to the ON position.
Note: Do not start the engine.
C. Use the electronic service tool to check for active diagnostic codes.
Diagnostic codes
Result: Diagnostic code 677-5 (444-5) is active or recently logged.
Proceed to Test Step 3.
Result: Diagnostic code 677-6 (444-6) is active or recently logged.
Proceed to Test Step 6.
3. Check the Battery Supply Voltage at the Relay Connector
A. Turn the keyswitch to the OFF position.
B. Turn the keyswitch to the ON position. Do not start the engine.
C. Measure the voltage between the battery input terminal on the relay and a suitable ground.
At least 11 VDC for a 12 VDC system. At least 22 VDC for a 24 VDC system.
Result: The voltage is not within the expected range.
Repair: Repair or replace the battery supply wiring to the start relay.
Use the electronic service tool to clear all logged diagnostic codes and verify that the repair eliminates the fault.
Result: The voltage is within the expected range.
Proceed to Test Step 4.
4. Create a Short Circuit at the Relay Connector
A. Turn the keyswitch to the OFF position.
B. Remove the start relay.
C. Fabricate a jumper wire. Install the jumper wire between terminal 1 and terminal 2 on the harness connector for the start relay.
D. Turn the keyswitch to the ON

Caterpillar parts catalog:

Caterpillar parts catalog
980H Wheel Loader MHG00001-UP (MACHINE) POWERED BY C-15 Engine
980K Wheel Loader GTZ00001-UP (MACHINE) POWERED BY C13 Engine


Parts plate Caterpillar catalog:

3T9525 PLATE AS-BRUSH
1090, 1190, 1190T, 120M, 120M 2, 1290T, 12M 2, 12M 3, 12M 3 AWD, 1390, 140M, 140M 2, 140M 3, 140M 3 AWD, 14H, 14M, 160M, 160M 2, 160M 3, 160M 3 AWD, 16H NA, 16M, 2290, 235, 235D, 2390, 2391, 245, 2491...
2531752 PLATE-THRUST
16G, 16H NA, 24H, 24M, 3406, 3406B, 3406C, 3406E, 3408, 3408B, 3408C, 3408E, 3412, 3412C, 3412D, 3412E, 3456, 365C, 365C L, 365C L MH, 374D L, 374F L, 375, 375 L, 385B, 385C, 385C FS, 385C L, 385C L M...
1591533 PLATE-SEALING
24M, 3406E, 3456, 365C, 365C L, 365C L MH, 374D L, 374F L, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 390F L, 583T, 587T, 621B, 621G, 623G, 627F, 627G, 631D, 631E, 631G, 633E II, 637D, 637E, 637G...
1756796 PLATE-VALVE
246C, 256C, 262C, 262C2, 272C, 277C, 277C2, 279C, 279C2, 287C, 287C2, 289C, 289C2, 297C, 299C, 365B, 365B II, 365B L, 365C, 365C L, 365C L MH, 374D L, 824C, 966G, 966G II, 966H, 972G, 972G II, 972H, 9...
8P2051 PLATE-CLUTCH
30/30, 572R, 572R II, 578, 583R, 583T, 587R, 587T, 611, 615, 615C, 637E, 69D, 735, 735B, 740, 740B, 768C, 769C, 769D, 770, 770G, 770G OEM, 771C, 771D, 772, 772G, 772G OEM, 776C, 776D, 777B, 777D, 777F...
8P1964 PLATE-CLUTCH
30/30, 572R, 572R II, 578, 583R, 583T, 587R, 587T, 611, 615, 615C, 814B, 814F, 814F II, 815B, 815F, 815F II, 816F, 816F II, 966D, 966F, 966F II, 966G, 966G II, 970F, 972G, 972G II, 972H, 972K, 972M, 9...
9G8020 PLATE-RETAINER
30/30, 572R, 572R II, 578, 583R, 583T, 587R, 587T, 611, 615, 615C, 814B, 814F, 814F II, 815B, 815F, 815F II, 816F, 816F II, 966D, 966F, 966F II, 966G, 966G II, 970F, 972G, 972G II, 972H, 972K, 980C, 9...
6I8500 PLATE-CLUTCH
30/30, 572R, 572R II, 578, 583R, 583T, 587R, 587T, 611, 615C, 814B, 814F, 815B, 815F, 816F, 966D, 966F, 966F II, 970F, 980C, 980F, 980F II, 980G, 980G II, 980H, 980K, D250E, D250E II, D25D, D300E, D30...
4Y5812 PLATE
235D, 365B, 365B II, 740, 740B, 769C, 769D, 771C, 771D, 772B, 773B, 773D, 775B, 775D, 776C, 776D, 777D, 824G II, 824H, 834B, 834G, 834H, 836, 836G, 836H, 844, 844H, 844K, 854G, 854K, 950F, 950F II, 95...
9W8269 PLATE-REACTION
572R, 578, 583R, 814B, 815B, 980C, 980F, 980F II, 980G, 980H, D6R, D6R II, D6R III, D7H, D7R, D7R II, D8N, D8R II, D8T
9M5140 PLATE AS
16, 525B, 525C, 535B, 535C, 545, 545C, 611, 613G, 615, 615C, 772, 814B, 814F, 814F II, 815B, 815F, 815F II, 816F, 816F II, 824C, 824G, 824G II, 824H, 824K, 825G, 825G II, 825H, 825K, 826C, 826G, 826G ...
1186606 PLATE-OUTER
824G, 824G II, 824H, 824K, 825G, 825G II, 825H, 825K, 826G, 826G II, 826H, 826K, 834B, 834G, 834H, 834K, 836, 836G, 836H, 836K, 980G, 980G II, 980H, 980K, 980K HLG, 980M, 986H, 988F II, 988G, 988H, 98...
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.