AVSPARE.COM
parts catalog

PLATE AS 3967328 - Caterpillar



3967328 PLATE AS Caterpillar parts 844K, 990K PLATE
Rating:
70
Alternative (cross code) number:
CA3967328
396-7328
3967328
Caterpillar 3967328 PLATE AS
Weight: 4 pounds 2 kg.

Buy PLATE AS 3967328 Caterpillar genuine, new aftermarket tractor parts with delivery
WHEEL DOZER, WHEEL LOADER,

Compatible equipment models: 3967328:

WHEEL DOZER  844K  
WHEEL LOADER  990K   Caterpillar
Number on catalog scheme: 4
 
  For full view, you need register

Information:


Illustration 30 g00857395
Remove the original oil return line from the air compressor. Install a new 148-0899 Hose As (85) to the air compressor. Connect the other end of 148-0899 Hose As to 6V-9837 Swivel Tee . Refer to 29.
Fill the hydraulic tank with 154-0195 Oil .
Illustration 31 g00866417
(I) 10 mm (0.39 inch) (J) 50 mm (1.97 inch)
Install 211-9987 Film (86). Use dimension (I) and (J) in order to locate the 211-9987 Film .Note: Damage to the charge pump will occur if the engine is started without oil in the propel pump.
Use the following procedure in order to check the propel pump for oil.
Illustration 32 g00866465
Install a 4137 kPa (600 psi) gauge on test port (87) for the charge pressure.
Illustration 33 g00866466
Remove wires (88) from the fuel solenoid.
Turn the key to the START position and crank the engine. Release the key when the charge pressure is registered on the gauge.
Reconnect wires (88) to the fuel solenoid.
Illustration 34 g00872501
Use the following process in order to purge the air from the differentials.
Start the engine. Run the engine at LOW idle.Note: Perform the following procedure on the outer covers of the differentials only.
Position drain plugs (89) that are located in the covers of the outer differentials at 12 O'clock.
Remove plugs (89) from the covers.
When the oil begins to appear in the holes of the covers, install plugs (89) .
Torque plugs (89) to 13 N m (10 lb ft).
Run the engine at HIGH idle. Engage the drive system in the FORWARD position and in the REVERSE position. Check for leaks in the hydraulic system.
Stop the engine.
Install the inner tires. Refer to Disassembly and Assembly, KENR7018, "Rear Tire - Remove and Install".
Install the drive shafts.
Install the outer tires. Refer to Disassembly and Assembly, KENR7018, "Rear Tire - Remove and Install".
Lower the machine.Note: Air pockets may exist in the hydraulic system after the installation procedure. While you operate the machine, the air pockets will move out of the hydraulic system. Monitor the oil level in the hydraulic tank. If necessary, add 154-0195 Oil .
Operate the machine for 10 to 15 minutes. Check for leaks.
Check the level of the oil in the hydraulic tank. If necessary, add 154-0195 Oil .

Caterpillar parts catalog:

Caterpillar parts catalog
844K Wheel Dozer K4Y00001-UP (MACHINE) POWERED BY C27 Engine
844K Wheel Dozer M4R00001-UP (MACHINE) POWERED BY C27 Engine
990K Wheel Loader K9X00001-UP (MACHINE) POWERED BY C27 Engine
990K Wheel Loader M9P00001-UP (MACHINE) POWERED BY C27 Engine
844K Wheel Dozer MBE00001-UP (MACHINE) POWERED BY C27 Engine
844K Wheel Dozer KLS00001-UP (MACHINE) POWERED BY C27 Engine
990K Wheel Loader A9P00001-UP (MACHINE) POWERED BY C27 Engine
990K Wheel Loader DJK00001-UP (MACHINE) POWERED BY C27 Engine


Parts plate Caterpillar catalog:

3T9525 PLATE AS-BRUSH
1090, 1190, 1190T, 120M, 120M 2, 1290T, 12M 2, 12M 3, 12M 3 AWD, 1390, 140M, 140M 2, 140M 3, 140M 3 AWD, 14H, 14M, 160M, 160M 2, 160M 3, 160M 3 AWD, 16H NA, 16M, 2290, 235, 235D, 2390, 2391, 245, 2491...
4N0342 PLATE-CAMSHAFT THRUST
16G, 16H NA, 245, 245D, 24H, 3406, 3406B, 3406C, 3408, 3408B, 3408C, 3408E, 3412, 3412C, 3412D, 3412E, 375, 375 L, 5080, 5110B, 578, 583R, 587R, 589, 621E, 621F, 623E, 623F, 627B, 627E, 627F, 631D, 63...
2253100 PLATE-SPACER
24H, 3412, 3412C, 3412D, 3412E, 5110B, 651E, 657E, 773B, 773D, 773E, 773F, 773G, 773G LRC, 773G OEM, 775B, 775D, 775E, 775F, 775G, 775G LRC, 775G OEM, 777C, 777D, 777F, 777G, 844, 844H, 844K, 854K, 99...
1T1897 PLATE-CLUTCH
773G, 773G OEM, 775G, 775G OEM, 776C, 776D, 777B, 777D, 777F, 777G, 784B, 784C, 785, 785B, 785C, 785D, 789, 789B, 789C, 789D, 793, 793B, 793C, 793D, 793F, 793F CMD, 793F OEM, 793F-XQ, 834G, 834H, 834K...
4J3816 PLATE
215, 215B, 225, 229, 235, 235B, 235D, 245, 245B, 24H, 24M, 5110B, 5130, 5130B, 5230, 5230B, 528, 589, 621, 621B, 621E, 621F, 621G, 621R, 623E, 623F, 623G, 627B, 627E, 627F, 627G, 631C, 631E, 631G, 633...
1894727 PLATE
12H, 140H, 14H, 16H, 330C, 330C FM, 330C L, 330C MH, 621G, 623G, 627G, 631E, 631G, 637E, 637G, 725, 730, 735, 735B, 740, 740B, 844K, 938G, 950G, 990K, 993K, D10N, D10R, D10T, D250E II, D300E II, D350E...
2G4553 PLATE
621B, 621E, 621F, 621G, 621H, 621K, 623E, 623F, 623G, 623H, 623K, 623K LRC, 627B, 627E, 627F, 627G, 627H, 627K, 627K LRC, 631E, 631G, 633E II, 637D, 637E, 637G, 641B, 650B, 651E, 657B, 657E, 657G, 666...
4E5609 PLATE
988G, 988H, 988K, 990, 990 II, 990H, 990K, 992G, 992K, R3000H
3P7584 PLATE-CLUTCH
844, 844H, 844K, 854G, 854K, 990, 990 II, 990H, 990K, 992C, 992D, 992G, 992K, 994, 994D, D10, D11N, D11R
3605943 PLATE-CLUTCH BACKING
735B, 740B, 770G, 770G OEM, 772G, 772G OEM, 844K, 990K
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.