3C8689 PLATE AS LH Caterpillar parts
Rating:
Alternative (cross code) number:
CA3C8689
3C-8689
3C8689
CA3C8689
3C-8689
3C8689
Weight: 4 pounds 2 kg.
For full view, you need register
Information:
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Link Bracket 3
B 1U-9200 Lever Puller Hoist 1 Start By:
Remove the electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit Injector - Remove".
Remove the valve mechanism cover base. Refer to Disassembly and Assembly, "Valve Mechanism Cover Base - Remove and Install".
Remove the fuel transfer pump. Refer to Disassembly and Assembly, "Fuel Transfer Pump - Remove".
Remove the turbochargers. Refer to Disassembly and Assembly, "Turbocharger - Remove".
Remove the exhaust elbows. Refer to Disassembly and Assembly, "Exhaust Elbow - Remove and Install".
Remove the water temperature regulator. Refer to Disassembly and Assembly, "Water Temperature Regulator - Remove and Install".
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products.Dispose of all fluids according to local regulations and mandates.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Do not turn the crankshaft or the camshaft while the camshaft gear is removed. If the rear gear group is not correctly timed during installation, interference can occur between the pistons and the valves, resulting in damage to the engine.
Note: Position the engine on top dead center for number one cylinder to aid in reassembly.
Drain the coolant from the cooling system into a suitable container for storage or disposal. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change".
Illustration 1 g01204694
Remove bolts (2) and washers (3).
Remove cover (1) and the O-ring seal.
Illustration 2 g01194581
Remove bolts (4). Remove gear (5).
Illustration 3 g01194585
Remove bolts (6), thrust plate (7), and adapter assembly (8).
Illustration 4 g01194626
Use bolt (6) in order to remove sealing plate (9). Remove the O-ring seals.
Illustration 5 g01204714
Remove tube assemblies (10).
Remove cover (11).
Disconnect harness assembly (12) and (13).
Remove bracket assembly (14).
Illustration 6 g01194679
Remove bolts (15) and damper (16).
Illustration 7 g01194687
Remove bolts (17). Remove sealing plate (18) and adapter assembly (19).
Illustration 8 g01194872
Remove supports (21).
Attach Tooling (A) and a suitable lifting device to cylinder head (22). Attach Tooling (B) to the side of cylinder head (22) that is near the turbocharger. The weight of cylinder head (22) is approximately 365 kg (800 lb).
Remove bolts (20) and (23).
Remove cylinder head (22). Remove the gaskets, O-ring seals, and the spacer plate.
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Link Bracket 3
B 1U-9200 Lever Puller Hoist 1 Start By:
Remove the electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit Injector - Remove".
Remove the valve mechanism cover base. Refer to Disassembly and Assembly, "Valve Mechanism Cover Base - Remove and Install".
Remove the fuel transfer pump. Refer to Disassembly and Assembly, "Fuel Transfer Pump - Remove".
Remove the turbochargers. Refer to Disassembly and Assembly, "Turbocharger - Remove".
Remove the exhaust elbows. Refer to Disassembly and Assembly, "Exhaust Elbow - Remove and Install".
Remove the water temperature regulator. Refer to Disassembly and Assembly, "Water Temperature Regulator - Remove and Install".
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products.Dispose of all fluids according to local regulations and mandates.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Do not turn the crankshaft or the camshaft while the camshaft gear is removed. If the rear gear group is not correctly timed during installation, interference can occur between the pistons and the valves, resulting in damage to the engine.
Note: Position the engine on top dead center for number one cylinder to aid in reassembly.
Drain the coolant from the cooling system into a suitable container for storage or disposal. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change".
Illustration 1 g01204694
Remove bolts (2) and washers (3).
Remove cover (1) and the O-ring seal.
Illustration 2 g01194581
Remove bolts (4). Remove gear (5).
Illustration 3 g01194585
Remove bolts (6), thrust plate (7), and adapter assembly (8).
Illustration 4 g01194626
Use bolt (6) in order to remove sealing plate (9). Remove the O-ring seals.
Illustration 5 g01204714
Remove tube assemblies (10).
Remove cover (11).
Disconnect harness assembly (12) and (13).
Remove bracket assembly (14).
Illustration 6 g01194679
Remove bolts (15) and damper (16).
Illustration 7 g01194687
Remove bolts (17). Remove sealing plate (18) and adapter assembly (19).
Illustration 8 g01194872
Remove supports (21).
Attach Tooling (A) and a suitable lifting device to cylinder head (22). Attach Tooling (B) to the side of cylinder head (22) that is near the turbocharger. The weight of cylinder head (22) is approximately 365 kg (800 lb).
Remove bolts (20) and (23).
Remove cylinder head (22). Remove the gaskets, O-ring seals, and the spacer plate.