AVSPARE.COM
parts catalog

PLATE ASSEM. 3Y8628 - Caterpillar


3Y8628 PLATE ASSEM. Caterpillar parts 950B, 966D
Rating:
82
Alternative (cross code) number:
CA3Y8628
3Y-8628
3Y8628
Caterpillar 3Y8628 PLATE ASSEM.
Weight: 0.05 pounds 0 kg.

Buy PLATE ASSEM. 3Y8628 Caterpillar genuine, new aftermarket tractor parts with delivery
WHEEL LOADER,

Compatible equipment models: 3Y8628:

WHEEL LOADER  950B   966D   Caterpillar
Number on catalog scheme: 3
  For full view, you need register

Information:


Illustration 1 g03442680
Remove four bolts (1), the four nuts, and the eight washers.
Raise auger assembly (2) to the highest position.
Turn off the engine.
Turn the battery disconnect switch to the OFF position.
Illustration 2 g03442876
Remove the bolts, the nuts, and auger segment (3) .
Illustration 3 g03442880
Install plate assembly, the two washers, and the two bolts.
Illustration 4 g03442881
Remove two bolts (6) and two washers.
Illustration 5 g03442882
Install guide assembly (9), two washers (7), and two bolts (8) .
Illustration 6 g03442883
Install plate assembly (10) .Note: Verify that the rear of plate assembly (10) is inside guide assembly (9) .
Illustration 7 g03442885
Illustration 8 g03443218
Note: The function of upper side plate (11), lower side plate (16), stop ring (12), and chain (17) is to keep plate assembly (10) in the correct position when auger assembly (2) is rotating.
Install upper side plate (11), lower side plate (16), two bolts (13), two washers (14), and two nuts (15) .
Install stop ring (12) .
Illustration 9 g03443258
Install chain (17), two washers (18), and nuts (19). Chain (17) must be installed onto the studs on lower side plate (16) and plate assembly (10) .
Illustration 10 g03443261
Install support assembly (20), two washers (21), and bolts (22) .Note: Lift the conduit assembly up in order to position support assembly (20) to the front portion of the screed. Lay the conduit assembly on support assembly (20) .
Illustration 11 g03443263
Personal injury can result from being struck by parts propelled by a released spring force.Make sure to wear all necessary protective equipment.Follow the recommended procedure and use all recommended tooling to release the spring force.
Connect one end of springs (23) to the chains on plate assembly (10). Connect the other end of springs (23) to support assembly (20) .Note: Adjust the location of springs (23) on the chains so that plate assembly (10) stays parallel when the screed is raised or lowered.
Illustration 12 g03443264
Illustration 13 g03443844
Install reduction plates (24) to each end gate. Retract the end gates into the screed.

Caterpillar parts catalog:

Caterpillar parts catalog
966D WHEEL LOADER 35S00001-02074 (MACHINE) POWERED BY 3306 ENGINE
950B WHEEL LOADER 65R00001-02823 (MACHINE) POWERED BY 3304 ENGINE
966D WHEEL LOADER 35S02148-02522 (MACHINE) POWERED BY 3306 ENGINE
966D WHEEL LOADER 35S02075-02147 (MACHINE) POWERED BY 3306 ENGINE
950B WHEEL LOADER 65R02824-03088 (MACHINE)
950E WHEEL LOADER 65R03089-UP (MACHINE) POWERED BY 3304 ENGINE
966E WHEEL LOADER 35S02524-UP (MACHINE) POWERED BY 3306 ENGINE


Parts plate Caterpillar catalog:

3G5980 PLATE
153, 416, 416B, 426B, 428, 428B, 438B, 446, 446B, 446D, 508, 515, 518, 518C, 525, 525B, 525C, 528, 535B, 535C, 539, 545, 545C, 814B, 814F, 814F II, 815B, 815F, 815F II, 816F, 816F II, 824C, 826C, 916,...
6H5139 PLATE-PRESSURE
120G, 12F, 12G, 130G, 140, 141, 14E, 14G, 153, 16, 163, 16G, 172, 173B, 183, 183B, 184, 191, 193, 30/30, 416, 416B, 426B, 428, 428B, 438B, 446, 46, 508, 515, 517, 518, 525, 525D, 527, 528, 535D, 545D,...
1U3508 PLATE
446B, 446D, 530B, 814F, 814F II, 815F, 815F II, 816F, 816F II, 918F, 924F, 928F, 938F, 938G, 938G II, 950B, 950B/950E, 950F, 950F II, 960F, 966D, 966F, 966F II, 966G, 966G II, 970F, 972G, 972G II, IT1...
9V0247 PLATE
318C, 320B, 320C, 325B L, 325C, 330B L, 330C, 345B II, 345B L, 814F, 814F II, 815F, 815F II, 824G, 824G II, 824H, 825G, 825G II, 825H, 918F, 928F, 936, 936F, 938F, 938G, 938G II, 950B, 950B/950E, 950F...
6P7968 PLATE-CLUTCH
517, 518, 527, 561M, 561N, 613C, 613C II, 613G, 931B, 936, 936F, 950B, 950B/950E, 950F, 950F II, 950G, 950G II, 950H, 950K, 960F, 962G, 962G II, 962H, 962K, 966C, 966H, 966K, 966M, 966R, D4H XL, D4HTS...
3T9496 PLATE-RETAINER
613C, 613C II, 613G, 936, 950B, 950B/950E, 966C, 966R, D5H, D5HTSK II, G936
9P8283 PLATE-CLUTCH
966D, 966F, 966F II, 970F, D6H, D6H XL, D6H XR
7G6060 PLATE-CENTER
527, 950B, 950B/950E, 950F, 950F II, 960F, 966C, D6N, R1300, R1300G
2V7092 PLATE-RETAINER
518, 528, 528B, 530B, 611, 613C, 613C II, 613G, 615, 615C, 725, 725C, 730, 730C, 735, 735B, 740, 740B, 814B, 815B, 816B, 950B, 950B/950E, 966D, 966F, D25C, D25D, D300E, D300E II, D30C, D350C, D350E, D...
4V6442 PLATE
815B, 826C, 926, 936F, 950B, 950F, 950F II, 966D, 966F, 966F II, 970F, 980C, 980F, RM-250C, RR-250B
2K0714 PLATE
508, 814, 815, 816, 936, 950, 950B, 950B/950E, 966C, 966D, 966F, 966G, 966R, G936
4V0015 PLATE-LOCK
12G, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 143H, 14G, 14H, 14H NA, 160G, 160H, 160H ES, 160H NA, 1...
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.