AVSPARE.COM
parts catalog

PLATE & FILM GP 4415841 - Caterpillar



4415841 PLATE & FILM GP Caterpillar parts PLATE
Rating:
16
Alternative (cross code) number:
CA4415841
441-5841
4415841
Caterpillar 4415841 PLATE & FILM GP

Buy PLATE & FILM GP 4415841 Caterpillar genuine, new aftermarket tractor parts with delivery

Number on catalog scheme:
 
  For full view, you need register

Information:


Never transport the machine with the engine running.
Comply with any laws that govern the characteristics of a load (length, width, height, and weight).
Illustration 1 g00543871
Move the hydraulic lockout control to the LOCKED position.
Turn the engine start switch to the OFF position in order to stop the engine. Remove the engine start switch key.
Turn the battery disconnect switch to OFF and remove the disconnect switch key.
Remove the ether starting aid cylinder.Reference: Refer to Operation and Maintenance Manual, "Ether Starting Aid Cylinder - Replace" for the removal procedure.
Lock the door and the access covers. Attach any vandalism protection.
The Product Link antenna (if equipped) may be repositioned in order to meet the regulations regarding height of some locations. The Product Link antenna is located on top of the cab. Perform the following procedure in order to move the Product Link antenna to the transport position.
Illustration 2 g02263573
Bracket in normal operating position.
Remove bolts (2) from bracket (1).
Illustration 3 g02270173
Reinstall bracket (1) with bolts (2) located in the top two holes of the bracket. Refer to illustration 3.Note: The bracket for the Product Link antenna must be place back into the normal operating position before the machine can be placed back into service.
The side view camera is located on top of the fuel tank and it must be repositioned for transport. Perform the following procedure in order to move the camera to the transport position.
Illustration 4 g06051521
Side view camera in position for transport
Loosen bolts (4) and (5) and slide the camera upward to the transport position.
Tighten bolts (4) and (5).Note: The side view camera must be placed back into the normal operating position before the machine can be placed back into service.
The platform light (if equipped) may be repositioned in order to meet the regulations regarding height of some locations. The platform light is located on top of the cab. Perform the following procedure in order to move the platform light to the transport position.
Illustration 5 g03670580
Remove bolts (2) from bracket (1).
Illustration 6 g03670582
Reinstall bracket (1) with bolts (2) located in the top two holes of the bracket. Refer to illustration 6.Note: The bracket for the platform light must be place back into the normal operating position before the machine can be placed back into service.
Cover the exhaust opening.
Do not allow the turbocharger to rotate while the engine is not operating. Damage to the turbocharger can result.
Note: Before you remove the excavator from the transport machine, remove the protective covering from the exhaust opening.
Illustration 7 g02142926
Chock the tracks and secure the machine with tie-downs. Make sure that you use the proper rated wire cable.Use the front towing eyes on the lower frame, the rear towing eyes on the lower frame. Also use the rear towing eye that is on the upper frame.Securely fasten all loose parts and all removed parts to the trailer or to the rail car.When the engine is stopped, the swing parking brake is automatically applied. The parking brake will prevent the upper structure from swinging.
In freezing weather, protect the cooling system with antifreeze, to the lowest

Caterpillar SIS machinery equipment:

Caterpillar SIS

Caterpillar parts catalog:

Caterpillar parts catalog
CS78B, CS76B Vibratory compactor 49200001-UP (MACHINE) POWERED BY C4.4 Engine
CS76B, CS78B Vibratory Soil Compactor CB700001-UP (MACHINE) POWERED BY C4.4 Engine


Parts plate Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.