AVSPARE.COM
parts catalog

PLATE-SIDE BAR 4416148 - Caterpillar



4416148 PLATE-SIDE BAR Caterpillar parts PLATE
Rating:
16
Alternative (cross code) number:
CA4416148
441-6148
4416148
Caterpillar 4416148 PLATE-SIDE BAR

Buy PLATE-SIDE BAR 4416148 Caterpillar genuine, new aftermarket tractor parts with delivery

Number on catalog scheme: 6
  
  For full view, you need register

Information:


Illustration 1 g03453518
Typical example
(1) Crankcase breather
(2) Air Intake
(3) Electronic Control Module (ECM)
(4) Oil Level Gauge (Dipstick)
(5) Location for Oil Sample Valve
(6) Oil Filter
(7) Oil Filler
(8) Secondary Fuel Filters
Illustration 2 g03453526
Typical example
(9) Front Lifting Eye
(10) Water Pump
(11) Coolant Intake
(12) Tensioner
(13) Belt
(14) Coolant Outlet
Illustration 3 g03453529
Typical example
(15) Rear Lifting Eye
(16) Alternator
(17) Turbocharger
(18) Starter Solenoid
(19) Starting Motor
(20) Oil Drain Plug
(21) Flywheel
(22) Flywheel Housing
(23) Coolant Drain Plug
Illustration 4 g03467856
Typical examples
(24) Electric Priming Pump
(25) Primary Fuel Filter
(26) Mechanical Priming Pump
(27) Primary Fuel Filter
(28) Spin on Crankcase Breather Note: Item (28) is part of the filtered breather system.Note: Some components may be supplied loose.The C4.4 diesel engine is electronically controlled. The C4.4 engine uses an Electronic Control Module (ECM) that receives signals from the fuel injection pump and other sensors in order to control the fuel injectors. The pump supplies fuel to the fuel injectors.The four cylinders are arranged in-line. The cylinder head assembly has two inlet valves and two exhaust valves for each cylinder. The ports for the exhaust valves are on the right side of the cylinder head. The ports for the inlet valves are on the left side of the cylinder head. Each cylinder valve has a single valve spring. Each cylinder has a piston cooling jet that is installed in the cylinder block. The piston cooling jet sprays engine oil onto the inner surface of the piston in order to cool the piston. The pistons have a Quiescent combustion chamber in the top of the piston in order to achieve clean exhaust emissions. The piston pin is off-center in order to reduce the noise level.The pistons have two compression rings and an oil control ring. The groove for the top ring has a hard metal insert in order to reduce wear of the groove. The skirt has a coating of graphite in order to reduce wear when the engine is new. The correct piston height is important in order to ensure that the piston does not contact the cylinder head. The correct piston height also ensures the efficient combustion of fuel which is necessary in order to conform to requirements for emissions.A piston and a connecting rod are matched to each cylinder. The piston height is controlled by the distance between the center of the big end bearing and the center of the small end bearing of the connecting rod. Three different lengths of connecting rods are available in order to attain the correct piston height. The three different lengths of connecting rods are made by machining the blank small end bearing of each rod at three fixed distances vertically above the centerline of the big end bearing.The crankshaft has five main bearing journals. End play is controlled by thrust washers which are located on both sides of the number 3 main bearing.The timing case is made of aluminum. The timing gears are stamped with timing marks in order to ensure the correct assembly of the gears. When the number 1 piston is at the top center position on the compression stroke, the marked

Caterpillar parts catalog:

Caterpillar parts catalog
352F Excavator WYA00001-UP (MACHINE) POWERED BY C13 Engine
352F Excavator RBF00001-UP (MACHINE) POWERED BY C13 Engine
324D L & 324D LN Excavators BTK00001-UP (MACHINE) POWERED BY C7 Engine
329D L & 329D LN Excavators EBM00001-UP (MACHINE) POWERED BY C7 Engine
329D L Excavator WLT00001-UP (MACHINE) POWERED BY C7 Engine
324E L & 324E LN Excavators LDG00001-UP (MACHINE) POWERED BY C7.1 Engine
320E, 320E L & 320E LN Excavators DFG00001-UP (MACHINE) POWERED BY C6.6 Engine
320E LRR Excavator PNL00001-UP (MACHINE) POWERED BY C6.6 Engine
323E L, 323E LN & 323E SA Excavators RAP00001-UP (MACHINE) POWERED BY C6.6 Engine


Parts plate Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.