AVSPARE.COM
parts catalog

PLATE-WEAR 4416291 - Caterpillar



4416291 PLATE-WEAR Caterpillar parts PLATE
Rating:
21
Alternative (cross code) number:
CA4416291
441-6291
4416291
Caterpillar 4416291 PLATE-WEAR
Weight: 0.08 pounds 0 kg.

Buy PLATE-WEAR 4416291 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:


Table 8
Messenger Pinout Specification    
Pins     Function    
1     + Battery    
2     - Battery    
3     Keyswitch    
7     CAN/J1939 High    
8     CAN/J1939 Low    
Connect the yellow wire (J1939+) to pin 7 on the connector for the display.
Connect the green wire (J1939-) to pin 8 on the connector for the display.
Connect pin 1 on the connector for the display to an unswitched +battery source.
Connect pin 2 on the connector for the display to a -battery source.
Connect pin 3 on the connector for the display to a switched +battery source.
Trim the shield (bare wire) back to the existing heat shrink tubing on the cable assembly. Position the 125-7876 Heat Shrink Tube so the shield is completely insulated and a proper seal may be obtained. Apply heat until a complete seal is formed. Be careful to avoid skin contact with any hot glue that may seep from the heat shrink tubing.
Reconnect the batteries.
Use a multimeter to measure the voltage. Measure the voltage between the +battery (pin 1) and battery ground (pin 2) with the key switch in the On position. The voltage should be 11 to 13.5 VDC for 12 volt systems, and 23 to 27 VDC for 24 volt systems.Note: The supply voltage to the Messenger display may be from 9 volts to 32 volts DC.
Use a multimeter to measure the voltage. Measure the voltage between the switched +battery (pin 3) and battery ground (pin 2) with the key switch in the On position. The voltage should be 11 to 13.5 VDC for 12 volt systems, and 23 to 27 VDC for 24 volt systems.
Turn the key switch to the Off position. Measure the voltage between the +battery (pin 1) and battery ground (pin 2). The voltage should be 11 to 13.5 VDC for 12 volt systems, and 23 to 27 VDC for 24 volt systems when the key switch is in the Off position.
Turn the key switch to the Off position. Measure the voltage between the switched +battery (pin 3) and battery ground (pin 2). The voltage should be 0 VDC when the key switch is in the Off position.
Place the gasket around the cutout on the front of the panel.
Insert the Messenger display into the panel.
Insert the display into the cutout from the front of the panel.
Install the rear brackets and loosely tighten the four screws that hold the brackets in place.
Ensure that the face of the Messenger display is straight and positioned correctly in the opening.
Fully tighten the four screws that hold the brackets in place.
Connect the 8-pin connector to the back of the display.
Secure the Messenger display wiring with tie straps in order to avoid wiring abrasion and interference with the operator.Gimbal Mount Installation
Required Tools
Table 9
Part number     Description    
151-0968     Drill    
9U-7330     Digital multimeter    
3S-2093     Tie straps    
6V-6193     Diagonal cutting pliers    
1U-7264     Standard screwdriver    
1U-7267     Phillips screwdriver    
6V-6194     Needle nose pliers  


Parts plate Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.