4426367 PLATE Caterpillar parts
236D, 242D, 246D, 257D, 259D, 262D, 272D, 272D XHP, 277D, 279D, 287D, 289D, 299D, 299D XHP
Rating:
Alternative (cross code) number:
CA4426367
442-6367
4426367
CA4426367
442-6367
4426367
Weight: 4 pounds 1 kg.
COMPACT TRACK LOADER, SKID STEER LOADER,
This part in 2 request:
Show.
This information for suppliers only!
2024-09-19
2023-06-21
Compatible equipment models: 4426367:
For full view, you need register
Information:
Installation Procedure
Note: Cleanliness is an important factor. Before assembly, thoroughly clean all parts in cleaning fluid. Allow the parts to air dry. Do not use wiping cloths or rags to dry parts. Lint may be deposited on the parts which may cause trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement. Dirt and other contaminants can damage the precision component. Perform assembly procedures on a clean work surface. Keep components covered and protected at all times.Note: Check the O-ring seals, the gaskets, and the seals for wear or for damage. Replace the components, if necessary.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.Dispose of all fluids according to local regulations and mandates.
Hot oil and hot components can cause personal injury. Do not allow hot oil or hot components to contact skin. At operating temperature, the engine coolant is hot and under pressure.Steam can cause personal injury.Check the coolant level only after the engine has been stopped and the cooling system pressure cap is cool enough to touch with your bare hand.Remove the cooling system pressure cap slowly to relieve pressure.Cooling system conditioner contains alkali. Avoid contact with the skin and eyes to prevent personal injury.
Note: Put identification marks on all lines, on all hoses, on all wires, and on all tubes for installation purposes. Cap all lines, all hoses, and all tubes and plug all lines, all hoses, and all tubes. This will help to prevent fluid loss and this will help to keep contaminants from entering the system.
Illustration 1 g01451058
Install bolts (8) in order to connect evaporator coil (4) to heater coil (5). Tighten bolts (8) to a torque of 12 3 N m (106 27 lb in).
Carefully install evaporator coil (4) and heater coil (5) as a unit. Install bolts (7).
Position the fittings and install nuts (11). Connect air conditioner hose assemblies (10).
Connect heater hoses (9).
Connect harness assemblies (3) and (6).
Illustration 2 g01233649
Install cover (2).
Illustration 3 g01451043
Turn heater hose valves (1) to the ON position.
Charge the air conditioner system. Refer to Service Manual, SENR5664, "Air Conditioning and Heating Systems with R-134a Refrigerant" for the procedure. Refer to Special Publication, NEDG2500, "Air Conditioning Tools" for the tools. End By:
Separate the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock - Separate and Connect".
Note: Cleanliness is an important factor. Before assembly, thoroughly clean all parts in cleaning fluid. Allow the parts to air dry. Do not use wiping cloths or rags to dry parts. Lint may be deposited on the parts which may cause trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement. Dirt and other contaminants can damage the precision component. Perform assembly procedures on a clean work surface. Keep components covered and protected at all times.Note: Check the O-ring seals, the gaskets, and the seals for wear or for damage. Replace the components, if necessary.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.Dispose of all fluids according to local regulations and mandates.
Hot oil and hot components can cause personal injury. Do not allow hot oil or hot components to contact skin. At operating temperature, the engine coolant is hot and under pressure.Steam can cause personal injury.Check the coolant level only after the engine has been stopped and the cooling system pressure cap is cool enough to touch with your bare hand.Remove the cooling system pressure cap slowly to relieve pressure.Cooling system conditioner contains alkali. Avoid contact with the skin and eyes to prevent personal injury.
Note: Put identification marks on all lines, on all hoses, on all wires, and on all tubes for installation purposes. Cap all lines, all hoses, and all tubes and plug all lines, all hoses, and all tubes. This will help to prevent fluid loss and this will help to keep contaminants from entering the system.
Illustration 1 g01451058
Install bolts (8) in order to connect evaporator coil (4) to heater coil (5). Tighten bolts (8) to a torque of 12 3 N m (106 27 lb in).
Carefully install evaporator coil (4) and heater coil (5) as a unit. Install bolts (7).
Position the fittings and install nuts (11). Connect air conditioner hose assemblies (10).
Connect heater hoses (9).
Connect harness assemblies (3) and (6).
Illustration 2 g01233649
Install cover (2).
Illustration 3 g01451043
Turn heater hose valves (1) to the ON position.
Charge the air conditioner system. Refer to Service Manual, SENR5664, "Air Conditioning and Heating Systems with R-134a Refrigerant" for the procedure. Refer to Special Publication, NEDG2500, "Air Conditioning Tools" for the tools. End By:
Separate the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock - Separate and Connect".
Parts plate Caterpillar catalog:
2869251
PLATE & FILM GP
216, 216B, 216B3, 226B, 226B3, 228, 232B, 236, 236B, 236B3, 236D, 242B, 242B3, 242D, 246C, 246D, 247, 247B, 247B3, 248, 252B, 252B3, 256C, 257B, 257B3, 257D, 259B3, 259D, 262C, 262C2, 267, 267B, 268B,...
216, 216B, 216B3, 226B, 226B3, 228, 232B, 236, 236B, 236B3, 236D, 242B, 242B3, 242D, 246C, 246D, 247, 247B, 247B3, 248, 252B, 252B3, 256C, 257B, 257B3, 257D, 259B3, 259D, 262C, 262C2, 267, 267B, 268B,...
246D, 262D, 272D, 277D, 279D, 287D, 289D, 299D, 65E, 75E, 85E, 924G, 924GZ, 924H, 924HZ, 95E, 993K, D6N, TH460B, TH560B
246D, 24M, 262D, 272D, 277D, 279D, 287D, 289D, 299D, 305.5E, 345D, 345D L, 345D L VG, 349D, 349D L, 35, 365B, 365B II, 365B L, 365C, 365C L, 365C L MH, 374D L, 385B, 385C, 385C FS, 385C L, 385C L MH, ...
3455853
PLATE
272D, 272D XHP, 299D, 299D XHP
272D, 272D XHP, 299D, 299D XHP
4307615
PLATE AS
272D, 272D XHP, 299D, 299D XHP
272D, 272D XHP, 299D, 299D XHP
4214212
PLATE AS
236D
236D
3888170
PLATE AS
236D, 242D, 257D, 259D
236D, 242D, 257D, 259D
4160743
PLATE
246D, 277D, 279D
246D, 277D, 279D
4160748
PLATE
246D, 262D, 277D, 279D, 287D, 289D
246D, 262D, 277D, 279D, 287D, 289D
4393100
PLATE
262D, 287D, 289D
262D, 287D, 289D
236D, 242D, 246D, 257D, 259D, 262D, 272D, 272D XHP, 277D, 279D, 287D, 289D, 299D, 299D XHP
4426366
PLATE
236D, 242D, 246D, 257D, 259D, 262D, 272D, 272D XHP, 277D, 279D, 287D, 289D, 299D, 299D XHP
236D, 242D, 246D, 257D, 259D, 262D, 272D, 272D XHP, 277D, 279D, 287D, 289D, 299D, 299D XHP
3456073
PLATE
236D, 242D, 246D, 257D, 259D, 262D, 272D, 272D XHP, 277D, 279D, 287D, 289D, 299D, 299D XHP
236D, 242D, 246D, 257D, 259D, 262D, 272D, 272D XHP, 277D, 279D, 287D, 289D, 299D, 299D XHP
3767203
PLATE-IDENTIFICATION
272D, 272D XHP, 299D, 299D XHP, 910K, 914K
272D, 272D XHP, 299D, 299D XHP, 910K, 914K
3456081
PLATE-AIR CONDITIONER
236D, 242D, 246D, 257D, 259D, 262D, 272D, 272D XHP, 277D, 279D, 287D, 289D, 299D, 299D XHP
236D, 242D, 246D, 257D, 259D, 262D, 272D, 272D XHP, 277D, 279D, 287D, 289D, 299D, 299D XHP
3454548
PLATE AS
272D, 272D XHP, 299D, 299D XHP
272D, 272D XHP, 299D, 299D XHP
3472165
PLATE-ADAPTER
312E, 312E L, 314E CR, 314E LCR, 316E L, 318E L, 416F, 420F, 428F, 430F, 432F, 434F, 444F, 450F, C4.4, C4.4XQ100, C4.4XQ80, CB-44B, CB-54B, CP-54B, CP-68B, CP-74B, CS-54B, CS-56B, CS-64B, CS-66B, CS-7...
312E, 312E L, 314E CR, 314E LCR, 316E L, 318E L, 416F, 420F, 428F, 430F, 432F, 434F, 444F, 450F, C4.4, C4.4XQ100, C4.4XQ80, CB-44B, CB-54B, CP-54B, CP-68B, CP-74B, CS-54B, CS-56B, CS-64B, CS-66B, CS-7...
3673564
PLATE
416F, 420F, 428F, 430F, 432F
416F, 420F, 428F, 430F, 432F
3564068
PLATE AS
416F, 420F, 428F, 430F, 432F, 434F, 444F, 450F
416F, 420F, 428F, 430F, 432F, 434F, 444F, 450F
3890485
PLATE
416F, 420F, 428F, 430F, 432F
416F, 420F, 428F, 430F, 432F
3613387
PLATE AS
2384C, 2484C, 312E, 312E L, 314E CR, 314E LCR, 316E L, 318E L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 323E L, 416F, 420F, 428F, 430F, 432F, 434F, 444F, 450F, 559C, 579C, 924K, 930K, 938K, C4.4, C4....
2384C, 2484C, 312E, 312E L, 314E CR, 314E LCR, 316E L, 318E L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 323E L, 416F, 420F, 428F, 430F, 432F, 434F, 444F, 450F, 559C, 579C, 924K, 930K, 938K, C4.4, C4....
3254374
PLATE-THRUST
120M 2, 2384C, 2484C, 2570C, 2670C, 312E, 312E L, 314E CR, 314E LCR, 316E L, 318E L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 323E L, 324E, 324E L, 324E LN, 329E, 329E L, 329E LN, 416F, 420F, 428F, 4...
120M 2, 2384C, 2484C, 2570C, 2670C, 312E, 312E L, 314E CR, 314E LCR, 316E L, 318E L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 323E L, 324E, 324E L, 324E LN, 329E, 329E L, 329E LN, 416F, 420F, 428F, 4...