4467241 PLATE-FRICTION Caterpillar parts
Rating:
Alternative (cross code) number:
CA4467241
446-7241
4467241
CA4467241
446-7241
4467241
Weight: 0.04 pounds 0 kg.
Information:
Removal Procedure
Start By:
Remove the heat shields, if equipped.
Remove the cover for the fuel injection nozzles. Refer to this Disassembly and Assembly Manual, "Fuel Injection Nozzle Cover - Remove and Install".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products.Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00951080
Remove the breather tube (3) from the valve mechanism cover (1). Refer to this Disassembly and Assembly Manual, "Crankcase Breather - Remove and Install".
Remove the fasteners (2). Remove valve mechanism cover (1). Remove the gasket from the cylinder head and discard the gasket. Installation Procedure
Illustration 2 g01149828
Thoroughly clean the valve mechanism cover (1). Ensure that the groove for the gasket for the valve mechanism cover (1) is clean and dry. Ensure that the mating face on the cylinder head is clean and dry.
If the valve mechanism cover (1) is equipped with an oil filler cap, check the condition of the O-ring for the oil filler cap. If necessary, replace the O-ring.
Check the condition of the fasteners (2). Replace the fasteners (2), if necessary.
Install the gasket and valve mechanism cover (1) on the cylinder head.
Illustration 3 g01149832
Install the fasteners (2). Tighten the fasteners in the sequence that is shown in Illustration 3to a torque of 9 N m (80 lb in).
Connect breather tube (3) to the valve mechanism cover. Refer to this Disassembly and Assembly Manual, "Crankcase Breather - Remove and Install". End By:
Install the cover for the fuel injection nozzles. Refer to this Disassembly and Assembly Manual, "Fuel Injection Nozzle Cover - Remove and Install".
If equipped, ensure that the heat shields are clean and free from dust, oil, and paint. Install the heat shields.
Start By:
Remove the heat shields, if equipped.
Remove the cover for the fuel injection nozzles. Refer to this Disassembly and Assembly Manual, "Fuel Injection Nozzle Cover - Remove and Install".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products.Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00951080
Remove the breather tube (3) from the valve mechanism cover (1). Refer to this Disassembly and Assembly Manual, "Crankcase Breather - Remove and Install".
Remove the fasteners (2). Remove valve mechanism cover (1). Remove the gasket from the cylinder head and discard the gasket. Installation Procedure
Illustration 2 g01149828
Thoroughly clean the valve mechanism cover (1). Ensure that the groove for the gasket for the valve mechanism cover (1) is clean and dry. Ensure that the mating face on the cylinder head is clean and dry.
If the valve mechanism cover (1) is equipped with an oil filler cap, check the condition of the O-ring for the oil filler cap. If necessary, replace the O-ring.
Check the condition of the fasteners (2). Replace the fasteners (2), if necessary.
Install the gasket and valve mechanism cover (1) on the cylinder head.
Illustration 3 g01149832
Install the fasteners (2). Tighten the fasteners in the sequence that is shown in Illustration 3to a torque of 9 N m (80 lb in).
Connect breather tube (3) to the valve mechanism cover. Refer to this Disassembly and Assembly Manual, "Crankcase Breather - Remove and Install". End By:
Install the cover for the fuel injection nozzles. Refer to this Disassembly and Assembly Manual, "Fuel Injection Nozzle Cover - Remove and Install".
If equipped, ensure that the heat shields are clean and free from dust, oil, and paint. Install the heat shields.
Caterpillar parts catalog:
Parts plate Caterpillar catalog:
4467240
PLATE-VALVE
Caterpillar
Caterpillar
4467239
PLATE-SEPARATOR
Caterpillar
Caterpillar
4467238
PLATE
Caterpillar
Caterpillar
4458454
PLATE-SUPPORT
Caterpillar
Caterpillar
4455790
PLATE
Caterpillar
Caterpillar
4450683
PLATE
Caterpillar
Caterpillar
4477574
PLATE
Caterpillar
Caterpillar
4471050
PLATE-COVER
Caterpillar
Caterpillar
4471049
PLATE
Caterpillar
Caterpillar
4468955
PLATE
Caterpillar
Caterpillar
4468069
PLATE AS
Caterpillar
Caterpillar
4468068
PLATE
Caterpillar
Caterpillar