AVSPARE.COM
parts catalog

PLATE 5088098 - Caterpillar



5088098 PLATE Caterpillar parts PLATE
Rating:
11
Alternative (cross code) number:
CA5088098
508-8098
5088098
Caterpillar 5088098 PLATE

Buy PLATE 5088098 Caterpillar genuine, new aftermarket tractor parts with delivery

Number on catalog scheme: 7
 
  For full view, you need register

Information:


Table 1
Required Tools    
Part     Description     Quantity    
198-4240     Digital Pressure Indicator     1    
163-0056     Hose Assembly (1)     1    
( 1 ) The hose assembly is not needed for harvester heads that are equipped with Caterpillar pressure taps.
Personal injury or death can result from escaping fluid under pressure.Escaping fluid under pressure, even a very small pin-hole size leak, can penetrate body tissue and cause serious injury and possible death. If fluid is injected into your skin, it must be treated immediately by a doctor familiar with this type of injury.Always use a board or cardboard when checking for a leak.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Prepare the machine for testing and adjusting.Reference: Testing and Adjusting, "Preparation for Troubleshooting"
Ensure that the hydraulic oil in the system is at normal operating temperature. To warm the hydraulic oil, operate the feed rollers for several minutes.
Illustration 1 g00874086
Place the harvester head in the HORIZONTAL position.
Shut off the engine.
Open the cover on the harvester head.
Illustration 2 g00876443
Control Valves HH300 (1) Pressure tap "M3". (2) Pressure reducing valve "R3".
If necessary, attach the adapter to the pressure tap "M3" (1) that is located on the left manifold. Attach the 198-4240 Digital Pressure Indicator to the pressure tap or the adapter. Set the pressure indicator to the "PSI" setting.Note: The pressure tap is clearly marked on the left manifold.
Start the engine. Press the operating mode switch in order to activate the working mode (wheel harvesters). Turn the engine speed dial until the engine is operating at 1300 rpm. Make sure that the switch for the controller is in the ON position.
Raise the harvester head approximately 0.9 m (3 ft) above the ground.
Press the button for delimbing knives close on the hand controls. Read the pressure on the pressure indicator. The pressure should be 14000 200 kPa (2030 30 psi).
If the pressure for the delimbing knives is correct go to step 14. If the pressure is not correct proceed to step 11.
Loosen the locknut on pressure reducing valve (2) for the delimbing knives close. Turn the adjustment screw clockwise in order to increase the pressure. Turn the adjustment screw counterclockwise in order to decrease the pressure.
Press the button for delimbing knives close on the hand controls. Adjust the pressure until the pressure indicator reads 14000 200 kPa (2030 30 psi).
Tighten the locknut on the adjustment screw of pressure reducing valve (2) .
Lower the harvester head to the ground.
Shut off the engine.
Remove the pressure indicator and the hose.
Close and latch the cover.

Caterpillar parts catalog:

Caterpillar parts catalog
C27 Generator Set 2A300001-UP


Parts plate Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.