5G9843 PLATE Caterpillar parts
D6H, D6H XL, D6H XR, D6R, D6R II, D6R III, D6R STD, D6T, D6T LGP, D6T LGPPAT, D6T XL, D7E, D7E LGP
Rating:
Alternative (cross code) number:
CA5G9843
5G-9843
5G9843
CA5G9843
5G-9843
5G9843
Weight: 5 pounds 2 kg.
Information:
MATERIAL THICKNESS
22
mm
NUMBER OF PITCH HOLES
6
OD
144.3
mm
PITCH CIRCLE DIAMETER
70
mm
PITCH CIRCLE HOLE DIAMETER
18
mm
TRACK-TYPE TRACTOR,
Compatible equipment models: 5G9843:
Information:
Transmission, SPN 2906 FMI 6Conditions Which Generate This Code:
Illustration 1 g01341071
Connections of the transmission shift solenoid 8
This diagnostic code is associated with the transmission clutch solenoid 8. The FMI 6 means that the ECM has determined that there is a short to ground in the solenoid circuit. The possible causes of this diagnostic code are listed:
The energize circuit of the solenoid is shorted to ground.
The solenoid has failed.
The ECM has failed. This is unlikely. Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear these diagnostic codes when the original diagnostic code has been corrected. Ensure that the diagnostic code of SPN 2906 FMI 6 is active before performing this procedure.Note: Use a digital multimeter for the measurements in this procedure.Test Step 1. CHECK THE SOLENOID.
Turn the disconnect switch and the key start switch to the ON position. Do not start the engine.
Observe the status of the diagnostic code.
Disconnect the solenoid with the active diagnostic code from the machine harness. Expected Result:The FMI 6 changes to FMI 5 when the solenoid is disconnected.Results:
YES - The FMI 6 changes to FMI 5 when the solenoid is disconnected. The circuit is correct.Repair: The solenoid has failed. Replace the solenoid. Verify that the new solenoid corrects the problem.STOP
NO - The SPN 2906 FMI 6 remains active. Proceed to Test Step 2.Test Step 2. CHECK THE ENERGIZE CIRCUIT OF THE SOLENOID FOR A SHORT TO GROUND.
Turn the key start switch and the disconnect switch to the OFF position.
The solenoid remains disconnected from the machine harness.
Disconnect the machine harness connector(s) from the ECM.
At the machine harness connector, measure the resistance from the signal contact J2-17 to all other contacts that are used in the machine harness connectors for the ECM. Expected Result:Each resistance measurement is greater than 5000 ohms.Results:
OK - Each resistance measurement is greater than 5000 ohms. The machine harness is correct. Proceed to Test Step 3.
NOT OK - Each resistance measurement is not greater than 5000 ohms. There is a short in the machine harness. The short is between J2-17 and the circuit with the low resistance measurement.Repair: Repair the machine harness or replace the machine harness. STOPTest Step 3. CHECK IF THE DIAGNOSTIC CODE REMAINS.
Inspect the harness connectors. Clean the contacts of the harness connectors and check the wires for damage to the insulation that is caused by excessive heat, battery acid, or chafing.
Perform a 45 N (10 lb) pull test on each of the wires that are associated with the circuit.
Reconnect all harness connectors. Make sure that the harness connectors are fully seated and that the clips for each connector are completely fastened.
Turn the disconnect switch and the key start switch to the ON position.
Operate the vehicle.
Check the status of the SPN 2906 FMI 6. Expected Result:The SPN 2906 FMI 6 is active.Results:
YES - The SPN 2906 FMI 6 is active. The diagnostic code has not been corrected.Repair: Check the circuit again. If the Caterpillar Electronic Technician (Cat ET) is available, use
Illustration 1 g01341071
Connections of the transmission shift solenoid 8
This diagnostic code is associated with the transmission clutch solenoid 8. The FMI 6 means that the ECM has determined that there is a short to ground in the solenoid circuit. The possible causes of this diagnostic code are listed:
The energize circuit of the solenoid is shorted to ground.
The solenoid has failed.
The ECM has failed. This is unlikely. Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear these diagnostic codes when the original diagnostic code has been corrected. Ensure that the diagnostic code of SPN 2906 FMI 6 is active before performing this procedure.Note: Use a digital multimeter for the measurements in this procedure.Test Step 1. CHECK THE SOLENOID.
Turn the disconnect switch and the key start switch to the ON position. Do not start the engine.
Observe the status of the diagnostic code.
Disconnect the solenoid with the active diagnostic code from the machine harness. Expected Result:The FMI 6 changes to FMI 5 when the solenoid is disconnected.Results:
YES - The FMI 6 changes to FMI 5 when the solenoid is disconnected. The circuit is correct.Repair: The solenoid has failed. Replace the solenoid. Verify that the new solenoid corrects the problem.STOP
NO - The SPN 2906 FMI 6 remains active. Proceed to Test Step 2.Test Step 2. CHECK THE ENERGIZE CIRCUIT OF THE SOLENOID FOR A SHORT TO GROUND.
Turn the key start switch and the disconnect switch to the OFF position.
The solenoid remains disconnected from the machine harness.
Disconnect the machine harness connector(s) from the ECM.
At the machine harness connector, measure the resistance from the signal contact J2-17 to all other contacts that are used in the machine harness connectors for the ECM. Expected Result:Each resistance measurement is greater than 5000 ohms.Results:
OK - Each resistance measurement is greater than 5000 ohms. The machine harness is correct. Proceed to Test Step 3.
NOT OK - Each resistance measurement is not greater than 5000 ohms. There is a short in the machine harness. The short is between J2-17 and the circuit with the low resistance measurement.Repair: Repair the machine harness or replace the machine harness. STOPTest Step 3. CHECK IF THE DIAGNOSTIC CODE REMAINS.
Inspect the harness connectors. Clean the contacts of the harness connectors and check the wires for damage to the insulation that is caused by excessive heat, battery acid, or chafing.
Perform a 45 N (10 lb) pull test on each of the wires that are associated with the circuit.
Reconnect all harness connectors. Make sure that the harness connectors are fully seated and that the clips for each connector are completely fastened.
Turn the disconnect switch and the key start switch to the ON position.
Operate the vehicle.
Check the status of the SPN 2906 FMI 6. Expected Result:The SPN 2906 FMI 6 is active.Results:
YES - The SPN 2906 FMI 6 is active. The diagnostic code has not been corrected.Repair: Check the circuit again. If the Caterpillar Electronic Technician (Cat ET) is available, use
Cat SIS web machinery list:
Parts plate Caterpillar catalog:
9T7767
PLATE-RETRACTION
120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 143H, 160G, 160H, 160H ES, 160H NA, 160K, 160M, 1...
120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 143H, 160G, 160H, 160H ES, 160H NA, 160K, 160M, 1...
9T7768
PLATE-WEAR
12G, 130G, 140G, 160G, D6H
12G, 130G, 140G, 160G, D6H
1022083
PLATE-VALVE
D6H, D6H XL, D6R, D6R II, D7R II
D6H, D6H XL, D6R, D6R II, D7R II
1003410
PLATE
120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 12H, 12H ES, 12H NA, 12K, 12M, 135H, 135H NA, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 143H, 160H, 160H ES, 160H NA, 160K, 160M, 163H, 163H NA, 24H, 824G...
120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 12H, 12H ES, 12H NA, 12K, 12M, 135H, 135H NA, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 143H, 160H, 160H ES, 160H NA, 160K, 160M, 163H, 163H NA, 24H, 824G...
1003411
PLATE-SPACER
120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 12H, 12H ES, 12H NA, 12K, 12M, 135H, 135H NA, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 143H, 160H, 160H ES, 160H NA, 160K, 160M, 163H, 163H NA, 24H, 824G...
120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 12H, 12H ES, 12H NA, 12K, 12M, 135H, 135H NA, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 143H, 160H, 160H ES, 160H NA, 160K, 160M, 163H, 163H NA, 24H, 824G...
1022063
PLATE-RETRACTION
854G, 992G, D6H, D6H XL, D6R, D6R II, D7R II
854G, 992G, D6H, D6H XL, D6R, D6R II, D7R II
9T1276
PLATE-PRESSURE
5130, 5130B, 5230, 5230B, 988F, D5B, D5E, D6D, D6E, D6E SR, D6F SR, D6G, D6G SR, D6G2 LGP, D6G2 XL, D6H
5130, 5130B, 5230, 5230B, 988F, D5B, D5E, D6D, D6E, D6E SR, D6F SR, D6G, D6G SR, D6G2 LGP, D6G2 XL, D6H
3462033
PLATE-REACTION
572R II, 583R, 583T, 587R, 587T, 814F, 814F II, 815B, 815F, 815F II, 816F, 816F II, 972H, 980C, 980F, 980G, 980G II, 980H, 980K, 980M, D6R II, D6R III, D6T, D7R II, D7R XR, D8R, D8R II, D8T, PL83, PL8...
572R II, 583R, 583T, 587R, 587T, 814F, 814F II, 815B, 815F, 815F II, 816F, 816F II, 972H, 980C, 980F, 980G, 980G II, 980H, 980K, 980M, D6R II, D6R III, D6T, D7R II, D7R XR, D8R, D8R II, D8T, PL83, PL8...
1838449
PLATE
583T, 587R, 587T, 621G, 627G, 631G, 637G, 963D, 973C, D7E, D7E LGP, D8R, D8R II, D8T, HA871, PL83, PL87, TK371, TK381
583T, 587R, 587T, 621G, 627G, 631G, 637G, 963D, 973C, D7E, D7E LGP, D8R, D8R II, D8T, HA871, PL83, PL87, TK371, TK381
2332535
PLATE
2470C, 2570C, 2670C, 330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 340D L, 340D2 L, 553C, 563C, 573C, 938G II, 950G II, 962G II, CB-44B, CB-54B, CD-54B, D6T LGP, D6T ...
2470C, 2570C, 2670C, 330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 340D L, 340D2 L, 553C, 563C, 573C, 938G II, 950G II, 962G II, CB-44B, CB-54B, CD-54B, D6T LGP, D6T ...
1889637
PLATE-RETRACTION
120M, 120M 2, 12M, 12M 2, 12M 3, 12M 3 AWD, 140M, 140M 2, 140M 3, 140M 3 AWD, 160M, 160M 2, 160M 3, 160M 3 AWD, 365B, 365B II, 554, 621K, 623K, 623K LRC, 627K, 627K LRC, 735, 735B, 740, 740B, 776D, 77...
120M, 120M 2, 12M, 12M 2, 12M 3, 12M 3 AWD, 140M, 140M 2, 140M 3, 140M 3 AWD, 160M, 160M 2, 160M 3, 160M 3 AWD, 365B, 365B II, 554, 621K, 623K, 623K LRC, 627K, 627K LRC, 735, 735B, 740, 740B, 776D, 77...
1559137
PLATE
120M 2, 12M 2, 12M 3, 12M 3 AWD, 140M 2, 140M 3, 140M 3 AWD, 160M 2, 160M 3, 160M 3 AWD, 330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 340D L, 340D2 L, 345B, 345B II,...
120M 2, 12M 2, 12M 3, 12M 3 AWD, 140M 2, 140M 3, 140M 3 AWD, 160M 2, 160M 3, 160M 3 AWD, 330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 340D L, 340D2 L, 345B, 345B II,...
1694364
PLATE
D6R
D6R
8E9907
PLATE
D6R
D6R
8E9909
PLATE
D6R
D6R
6V2226
PLATE-WARNING
517, 527, 572R, 572R II, 583R, 583T, 587R, 587T, D5HTSK II, D6H, D6H II, D6H XL, D6H XR, D6R, D6R II, D6R III, D6T, D7H, D7R, D7R II, D7R XR, D8N, D8R, D8R II, D8T, D9R, D9T
517, 527, 572R, 572R II, 583R, 583T, 587R, 587T, D5HTSK II, D6H, D6H II, D6H XL, D6H XR, D6R, D6R II, D6R III, D6T, D7H, D7R, D7R II, D7R XR, D8N, D8R, D8R II, D8T, D9R, D9T
5G9963
PLATE AS
D6H, D6H II, D6H XL, D6H XR, D6R, D6R II
D6H, D6H II, D6H XL, D6H XR, D6R, D6R II
4511573
PLATE AS
D6R, D6R II, D6R III, D6T, D6T LGP, D6T LGPPAT, D6T XL
D6R, D6R II, D6R III, D6T, D6T LGP, D6T LGPPAT, D6T XL
3W2369
PLATE AS
517, 527, 561M, 561N, 572R, 572R II, D4H, D4H XL, D4HTSK II, D4HTSK III, D5H, D5H XL, D5HTSK II, D5M, D5N, D5R LGP, D6H, D6H II, D6H XL, D6H XR, D6M, D6N, D6N LGP, D6N OEM, D6R, D6R II, D6R III, D6R S...
517, 527, 561M, 561N, 572R, 572R II, D4H, D4H XL, D4HTSK II, D4HTSK III, D5H, D5H XL, D5HTSK II, D5M, D5N, D5R LGP, D6H, D6H II, D6H XL, D6H XR, D6M, D6N, D6N LGP, D6N OEM, D6R, D6R II, D6R III, D6R S...
1Q1544
PLATE
D6R, D6R II
D6R, D6R II
1601784
PLATE
D6R
D6R
1601786
PLATE
D6R
D6R
1601785
PLATE
D6R
D6R
6Y6835
PLATE
D6H, D6R, D6R II, D6R III, D6T
D6H, D6R, D6R II, D6R III, D6T