5I7541 PLATE Caterpillar parts
311, 311B, 312B, 320, 320 L, 320B, 320B L, 320C, 320N, 321B
Rating:
Alternative (cross code) number:
CA5I7541
5I-7541
5I7541
CA5I7541
5I-7541
5I7541
Weight: 0.05 pounds 0 kg.
EXCAVATOR,
Compatible equipment models: 5I7541:
Number on catalog scheme:
8
For full view, you need register
Caterpillar parts catalog:
Information:
1. Install tooling (A) as follows: a) Install pilot (1) on the end of the crankshaft. Install bolts (4) and tighten enough to hold the pilot (1). Put wear sleeve on pilot (1) with the outside angle toward the rear of the engine. Push the sleeve on the crankshaft to put pilot (1) in the center, then tighten bolts (4).b) Put ring (2) on plate (5) and put this assembly on to the stud of pilot (1). Put on nut (3) and push the sleeve on to the crankshaft. Remove tooling (A).end by: a) install crankshaft rear sealb) install flywheelRemove Flywheel Housing
start by: a) remove starterb) remove flywheel1. Loosen the bolts that hold the oil pan to the cylinder block. Remove the bolts that hold the oil pan to the flywheel housing. Fasten a hoist to the rear of the engine. Lift the rear of the engine and install shims on each side of the cylinder block. 2. Remove the bolts (2) and locks that hold the flywheel housing in place. Remove flywheel housing (1).Install Flywheel Housing
1. Clean the contact surfaces of the flywheel housing and cylinder block. Install a new gasket. 2. Put oil on the lip of the rear seal. Put flywheel housing in position and install the locks and bolts.3. Cut the gasket so it is even with the bottom of the block and flywheel housing. Remove the shims from each side of the block and tighten the bolts for the oil pan. Install remainder of bolts in oil pan.4. Install the starter. end by: a) install flywheel
start by: a) remove starterb) remove flywheel1. Loosen the bolts that hold the oil pan to the cylinder block. Remove the bolts that hold the oil pan to the flywheel housing. Fasten a hoist to the rear of the engine. Lift the rear of the engine and install shims on each side of the cylinder block. 2. Remove the bolts (2) and locks that hold the flywheel housing in place. Remove flywheel housing (1).Install Flywheel Housing
1. Clean the contact surfaces of the flywheel housing and cylinder block. Install a new gasket. 2. Put oil on the lip of the rear seal. Put flywheel housing in position and install the locks and bolts.3. Cut the gasket so it is even with the bottom of the block and flywheel housing. Remove the shims from each side of the block and tighten the bolts for the oil pan. Install remainder of bolts in oil pan.4. Install the starter. end by: a) install flywheel
Parts plate Caterpillar catalog:
1090, 1190, 1190T, 1290T, 1390, 2290, 2390, 2391, 307, 307B, 307D, 307E, 308E, 311, 311B, 311C, 312, 312B, 312B L, 312C L, 313B, 314C, 315, 315B, 315B FM L, 315C, 317, 318B, 318C, 319C, 320 L, 320B, 3...
311, 311B, 311C, 311D LRR, 311F LRR, 312, 312B L, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313B, 313D, 313D2, 313D2 LGP, 314C, 314D LCR, 314E CR, 314E LCR, 315, 316E L, 320D...
308E, 308E CR, 308E SR, 311, 311B, 312, 312B, 312B L, 315, 315B, 315B FM L, 315B L, 317, 317B LN, 318B
315, 315B, 315B L, 315C, 315D L, 316E L, 317, 317B LN, 318B, 318C, 318D L, 318D2 L, 318E L, 319C, 319D, 319D L, 319D LN, 320 L, 320B, 320B FM LL, 320B U, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM ...
315C, 315D L, 318B, 318C, 318E L, 319C, 319D, 319D L, 319D LN, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 320E, 320E L, 32...
1090, 1190, 1190T, 1290T, 1390, 2290, 2390, 2391, 2491, 2590, 320B, 321B, 322B L, 322C, 322C FM, 324D FM, 324D FM LL, 325B, 325B L, 325C FM, 325D FM, 325D FM LL, 330B L, 330C FM, 330C L, 330D FM, 330D...
311, 311B, 311C, 311D LRR, 312, 312B, 312C, 312C L, 312D, 312D L, 313D, 314C, 314D CR, 314D LCR, 315D L, 318C, 318D L, 319C, 319D, 319D L, 319D LN, 320, 320 L, 320B, 320C, 320C FM, 320C L, 320D, 320D ...
311, 311B, 311C, 311D LRR, 312, 312B, 312C, 312C L, 312D, 312D L, 313D, 314C, 314D CR, 314D LCR, 315D L, 318C, 318D L, 319C, 319D, 319D L, 319D LN, 320, 320 L, 320B, 320C, 320C FM, 320C L, 320D, 320D ...
311C, 313D2 LGP, 315C, 315D L, 316E L, 318C, 318D L, 318D2 L, 318E L, 319C, 319D, 319D L, 319D LN, 320C, 320C L, 320D, 320D FM, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 3...
311, 318C, 319C, 320B, 320B U, 320C, 320C FM, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320N, 321C, 321D LCR, 323D L, 323D LN, 323D SA
315C, 315D L, 318C, 318E L, 319C, 319D, 319D L, 319D LN, 320C, 320C L, 320D, 320D FM, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 3...
315D L, 316E L, 318C, 318D L, 318E L, 319C, 319D, 319D L, 319D LN, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 320E, 320E L...
1219078
PLATE ASSEM.
311B, 312B
311B, 312B
1502224
PLATE ASSEM.
311B, 312B
311B, 312B
1315887
PLATE
311B, 312B
311B, 312B
1232784
PLATE ASSEM.
311B, 312B
311B, 312B
1026452
PLATE KIT
311, 311B
311, 311B
6I6512
PLATE
311, 311B
311, 311B
1373627
PLATE
311B, 320B L, 325B, 330B, 345B II
311B, 320B L, 325B, 330B, 345B II
1235581
PLATE
311B, 312B, 325B, 330B, 345B, 345B L
311B, 312B, 325B, 330B, 345B, 345B L
1219086
PLATE ASSEM.
311B, 312B
311B, 312B
1219083
PLATE ASSEM.
311B, 312B
311B, 312B
1319906
PLATE
311B, 312B
311B, 312B
1319881
PLATE
311B, 312B
311B, 312B