AVSPARE.COM
parts catalog

PLATE (Right Hand) 5K3210 - Caterpillar


5K3210 PLATE (Right Hand) Caterpillar parts 950
Rating:
23
Alternative (cross code) number:
CA5K3210
5K-3210
5K3210
Caterpillar 5K3210 PLATE (Right Hand)
Weight: 57 pounds 25 kg.

Buy PLATE (Right Hand) 5K3210 Caterpillar genuine, new aftermarket tractor parts with delivery
WHEEL LOADER,

Compatible equipment models: 5K3210:

WHEEL LOADER  950   Caterpillar
Number on catalog scheme: 13
  For full view, you need register

Information:


Illustration 1 g01224959Raise
In order to raise the ROPS, perform the following steps:
Raise the ROPS to the full upright position.
Install locking pins (1) through the ROPS post.
Install cotter pins (2) through locking pins (1). This will lock the locking pins in place.
Illustration 2 g01224960
Tighten locking lever (3). Note: In order to tighten the locking lever, perform the following procedure:
Turn the locking lever clockwise. Turn the locking lever by one-half turn.
Raise the locking lever in order to turn the lever without turning the jacking screw.
Turn the locking lever counterclockwise by one-half turn.
Release the locking lever. This will allow the locking lever to engage the jacking screw.
Repeat steps 4.a through 4.d until the locking pin is tight. Move the locking lever to the full counterclockwise position after the locking lever is tightened. Lower
In order to lower the ROPS, perform the following steps:
Loosen locking lever (3). Note: In order to loosen the locking lever, perform the following procedure:
Raise the locking lever in order to turn the lever without turning the jacking screw.
Turn the locking lever clockwise by one-half turn.
Release the locking lever. This will allow the locking lever to engage the jacking screw.
Turn the locking lever counterclockwise by one-half turn.
Repeat steps 1.a through 1.d until the locking pin is loosened.
Remove cotter pins (2).
Remove locking pins (1).
Lower the ROPS toward the rear of the machine.
In order to store the front locking pins, install the front locking pins into the holes on the ROPS post.
Install front cotter pins (2) through front locking pins (1). This will lock the locking pins in place. Note: In order to increase the life of the gas springs, store the ROPS in the folded position when the machine is unused for an extended period of time.

Caterpillar parts catalog:

Caterpillar parts catalog
950 WHEEL LOADER 31K00001-00942 (MACHINE)
950 WHEEL LOADER 31K00943-01200 (MACHINE)


Parts plate Caterpillar catalog:

6H5139 PLATE-PRESSURE
120G, 12F, 12G, 130G, 140, 141, 14E, 14G, 153, 16, 163, 16G, 172, 173B, 183, 183B, 184, 191, 193, 30/30, 416, 416B, 426B, 428, 428B, 438B, 446, 46, 508, 515, 517, 518, 525, 525D, 527, 528, 535D, 545D,...
8P9770 PLATE
14G, 215, 215B, 215C, 215D, 225, 225D, 229, 229D, 231D, 235, 235B, 235C, 235D, 245, 245B, 24H, 24M, 307C, 311C, 311D LRR, 311F LRR, 312, 312B L, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 3...
7N9342 PLATE-THRUST
120G, 12G, 130G, 140B, 140G, 14G, 160H, 1673C, 215, 235, 3204, 330 L, 3304, 3304B, 3306, 3306B, 330B, 350, 518, 528, 561D, 571G, 572G, 627B, 637D, 639D, 815, 816, 916, 920, 926, 930, 931B, 936F, 941, ...
4S6417 PLATE-THRUST
120G, 130G, 215B, 225, 3304, 3304B, 515, 517, 518C, 525, 527, 920, 936F, 941, 950, 951B, 955H, D320A, D330A, D4D, D4E, D4E SR, D4H, D4H XL, D4HTSK III, D5H, D5H XL, D5HTSK II, G3304, G3304B
8S5169 PLATE ASSEM.
1673C, 16G, 245, 3304, 3306, 3406, 3406B, 3408, 3412, 627B, 950, 983B, D6C, D7F, D8H, D8K
5S1213 PLATE
120, 120B, 12F, 140, 140B, 14E, 16, 16G, 245, 245B, 245D, 3304B, 3306, 5130, 5130B, 5230, 5230B, 561B, 561C, 572G, 578, 589, 594H, 613, 621, 621B, 621E, 621F, 621R, 623, 623E, 623F, 627, 627B, 627E, 6...
8N3663 PLATE-BLOCK
120G, 130G, 3304, 518, 920, 930, 941, 950, 951B, 955L, D4E, G3304
1T0290 PLATE-CLAMP
517, 518, 518C, 613, 613B, 613C, 613C II, 920, 930, 930R, 936, 936F, 941, 950, 955H, 966C, 966R, D250D, D4D, D4E, D4H, D4H XL, D4HTSK II, D4HTSK III, G936
2K5127 PLATE
518, 528, 613, 613B, 814, 815, 950, 966C, 980, 980B, D35C, D44B, D550B
2K0714 PLATE
508, 814, 815, 816, 936, 950, 950B, 950B/950E, 966C, 966D, 966F, 966G, 966R, G936
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.