5L7510 PLATE Caterpillar parts
3181
Rating:
Alternative (cross code) number:
CA5L7510
5L-7510
5L7510
CA5L7510
5L-7510
5L7510
Weight: 9 pounds 4 kg.
MARINE GEAR,
Compatible equipment models: 5L7510:
Information:
Installation Procedure
Illustration 1 g00667338
Remove the former throttle cable. Remove the two yoke rod ends (4) from each end of the former throttle cable.
Install the two yoke rod ends on the new 176-6767 Cable .
Remove accelerator pedal (1) and housing (8) from the machine cab.
Install the 176-6767 Cable, guide (5), spring (6), and guide (7) on accelerator pedal (1) and housing (8). The assembly is shown in the above illustration.
Fully extend the cable and attach yoke rod end (4) to accelerator pedal lever (2). Adjust accelerator pedal lever (2) until the accelerator pedal lever makes contact with housing (8). Tighten nut (9) .
Install the assembled accelerator pedal, the throttle cable, and the housing into the machine cab.
Illustration 2 g00668292
Route the throttle cable to the engine. The routing is illustrated above.
Illustration 3 g00668295
Assemble seal (10) and nut (15) on the engine end of the cable assembly.
Screw rod end (12) onto the cable until the threads bottom. Align the rod end at the governor lever and lock the assembly with a bolt (15). Attach the cable assembly to the engine with bolt (11), locknut (14), and washer (13) .
Check the high idle speed and the low idle speed of the engine. Adjust the bulkhead nuts on the cable at the actuator on the governor to set speeds.
Illustration 1 g00667338
Remove the former throttle cable. Remove the two yoke rod ends (4) from each end of the former throttle cable.
Install the two yoke rod ends on the new 176-6767 Cable .
Remove accelerator pedal (1) and housing (8) from the machine cab.
Install the 176-6767 Cable, guide (5), spring (6), and guide (7) on accelerator pedal (1) and housing (8). The assembly is shown in the above illustration.
Fully extend the cable and attach yoke rod end (4) to accelerator pedal lever (2). Adjust accelerator pedal lever (2) until the accelerator pedal lever makes contact with housing (8). Tighten nut (9) .
Install the assembled accelerator pedal, the throttle cable, and the housing into the machine cab.
Illustration 2 g00668292
Route the throttle cable to the engine. The routing is illustrated above.
Illustration 3 g00668295
Assemble seal (10) and nut (15) on the engine end of the cable assembly.
Screw rod end (12) onto the cable until the threads bottom. Align the rod end at the governor lever and lock the assembly with a bolt (15). Attach the cable assembly to the engine with bolt (11), locknut (14), and washer (13) .
Check the high idle speed and the low idle speed of the engine. Adjust the bulkhead nuts on the cable at the actuator on the governor to set speeds.
Caterpillar parts catalog:
Parts plate Caterpillar catalog:
4L6923
PLATE ASSEM.
3181, D353C
3181, D353C
4L9381
PLATE ASSEM
3181, D353C
3181, D353C
4L6932
PLATE ASSEM.
3181, D353C
3181, D353C
1L9366
PLATE
3181, D346, D353C, D375D
3181, D346, D353C, D375D
4L4333
PLATE (SERIAL NO.)
3181, 3192, 7211, 7231, 7241, 7251, 7261, 7271
3181, 3192, 7211, 7231, 7241, 7251, 7261, 7271
4L8512
PLATE
3181, 3192
3181, 3192
6L7541
PLATE
3181
3181
2H5279
PLATE
3181, D364, D375D
3181, D364, D375D
2H5278
PLATE (CENTER)
3181, D364, D375D
3181, D364, D375D
1L9306
PLATE
3181
3181
4L6922
PLATE ASSEM.
3181
3181
5L4611
PLATE
3181
3181
7M9960
PLATE
D397D
D397D
4L3752
PLATE ASSEM.
D343
D343
6L2180
PLATE
D333A
D333A
4L9786
PLATE
D333A
D333A
4L9790
PLATE
D333A
D333A
7M3841
PLATE
D8H, D9E
D8H, D9E
5L4611
PLATE
3181
3181
5L9638
PLATE
D333A
D333A
5L9650
PLATE
1673, D320A, D330A, D333A
1673, D320A, D330A, D333A
6L4667
PLATE
D342C
D342C
5L5747
PLATE
D343
D343
4L1309
PLATE
3192
3192