parts catalog

PLATE 5V3614 - Caterpillar

5V3614 PLATE Caterpillar parts PLATE
Alternative (cross code) number:
Caterpillar 5V3614 PLATE
Weight: 124 pounds 56 kg.

Buy PLATE 5V3614 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register


Installation Procedure
Table 1
Required Tools
Item Qty Part Number Description
A 4 138-7575 Link Bracket Note: Cleanliness is an important factor. Before installation, all components and mating surfaces should be thoroughly clean. Inspect all parts. Parts that are worn or damaged should be replaced with new parts. Inspect all gaskets and seals. Replace gaskets and seals that are worn or damaged. All installation procedures should be performed in a clean work area.
Illustration 1 g00798959
Install shroud (15) on hydraulic oil cooler core (12).
Illustration 2 g00798956
Attach a suitable lifting device and a hoist to mount assembly (14) for the hydraulic cooling fan motor and the fan spider. Install mount assembly (14) on oil cooler core (12). Note: The mount assembly, the hydraulic cooling fan motor, and the fan spider weigh approximately 94 kg (207 lb).
Illustration 3 g00798955
Attach a suitable lifting device and a hoist to Tooling (A) at the top mount assemblies of oil cooler core (12). Attach a suitable lifting device to Tooling (A) at the lower mount assemblies of oil cooler core (12). Use the two separate lifting devices to tilt oil cooler core (12) as you install oil cooler core (12) in hydraulic oil cooler (3). Note: You must tilt the oil cooler core in order to provide clearance for the brackets at the top of the guard assembly. The oil cooler core weighs approximately 800 kg (1764 lb).
Illustration 4 g00798945
Install bolts and caps (13) to secure oil cooler core (12) at the four mounting locations within the guard group.
Remove the lifting devices and Tooling (A). After you remove Tooling (A), install the bolt in each of the four mount assemblies of oil cooler core (3).
Illustration 5 g00798942
Install block (11) on hydraulic oil cooler (3).
Illustration 6 g00798934
Attach a suitable lifting device and a hoist to the top of the guard assembly of hydraulic oil cooler (3). Use the hoist to position hydraulic oil cooler (3) on the machine. Note: The hydraulic oil cooler weighs approximately 1160 kg (2557 lb).
Illustration 7 g00798936
Use three bolts (10) to secure each of the four mounting pads on hydraulic oil cooler (3) to the machine.
Illustration 8 g00798931
Connect hose (8) and hose (9) at the bottom corner of hydraulic oil cooler (3).
Illustration 9 g00798927
Connect hose (6) at the top of hydraulic oil cooler (3). Secure hose (6) with clamps (7).
Illustration 10 g00798923
Install plates (5) at the lower corners of the guard assembly of hydraulic oil cooler (3).
Install hoses (4) for the hydraulic cooling fan motor. Note: Refer to the markings on the hoses.
Illustration 11 g00798914
Use two people to install upper grate (1) and lower grate (2) from the guard assembly of hydraulic oil cooler (3). Note: Each grate weighs approximately 31 kg (68 lb).
Fill the hydraulic oil. Refer to Operation and Maintenance Manual, "Hydraulic System Oil - Change".

Parts plate Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.