6L4750 PLATE ASSEM. Caterpillar parts
3304, 3306, 3406, 3408, 3412, D342C, D343, D379A, G3304, G342C, G343, G379, RM-300
Rating:
Alternative (cross code) number:
CA6L4750
6L-4750
6L4750
CA6L4750
6L-4750
6L4750
Weight: 12 pounds 5 kg.
GAS ENGINE, RECLAIMER MIXER,
This part in 9 request:
Show.
This information for suppliers only!
2024-07-02
2023-08-08
2023-07-05
2023-06-24
2022-10-14
2020-04-01
2018-10-08
2017-09-18
2017-07-17
Compatible equipment models: 6L4750:
Information:
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 8H-0663 Bearing Puller 1
5F-7345 Puller 1
126-7183 Crossblock 1
126-7177 Puller Leg 2
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Remove the auxiliary equipment from the accessory drive housing. Refer to the Original Equipment Manufactures (OEM) for the correct procedure.
Illustration 1 g03360850
If the OEM driven equipment has not been installed to the auxiliary drive, remove bolts (1). Remove cover plate (2) and remove O-ring seal (3) (not shown).
Illustration 2 g03431636
Remove circlip (9) from housing (4).
Remove gear assembly (6) from housing (4).
If necessary, follow Step 5.a through Step 5.c in order to disassemble gear assembly (6).
Remove circlip (8) from gear assembly (6).
Use Tooling (A) in order to remove bearing (7) from gear (6).
Use a suitable tool in order to remove bearing (5) from housing (4). Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
B 7M-7456 Bearing Mount Compound -
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 3 g03431639
Apply a small continuous bead of Tooling (B) to outer Surface (X) of bearing (5).
Use a suitable tool in order to install bearing (5) to housing (4). Remove any excess bearing mount compound.
Illustration 4 g03431658
Illustration 5 g03431659
If necessary, follow Step 3.a through Step 3.g in order to assemble bearing (7) onto gear (6).
Inspect the condition of the teeth and the splines of gear (6) for wear and damage. Inspect bearing (7) circlip (8) and circlip (9).
Inspect the bore in housing (4) for damage. If necessary, replace the front housing. Refer to Disassembly and Assembly, "Housing (Front) - Remove" and Disassembly and Assembly, "Housing (Front) - Install" for the correct procedure.
Apply a small continuous bead of Tooling (B) to inner Surface (Y) of bearing (7). Place the inner race of bearing (7) onto a suitable support. Press the shaft of gear (6) into bearing (7) until the shoulder of the gear is against the bearing. Remove any excess bearing mount compound.
Install circlip (8) into the groove in gear (6).
Apply a small continuous bead of Tooling (B) to the outer Surface (Z) of bearing (7)
Install gear assembly (6) to housing (4). Ensure that the shaft of gear (6) is correctly aligned with the bearing in housing (4). Remove any excess bearing mount compound.
Install circlip (9) into the groove in accessory drive housing (4). Ensure that circlip (9) is correctly positioned in the groove.
Ensure that there is tactile backlash between the idler gear and the accessory drive gear.
Illustration 6 g03360850
Install the auxiliary equipment to the accessory drive housing. Refer to the OEM for the correct procedure.
If the OEM driven equipment is not being installed to the auxiliary drive. Install a new O-ring seal (3) (not shown) and
Table 1
Required Tools
Tool Part Number Part Description Qty
A 8H-0663 Bearing Puller 1
5F-7345 Puller 1
126-7183 Crossblock 1
126-7177 Puller Leg 2
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Remove the auxiliary equipment from the accessory drive housing. Refer to the Original Equipment Manufactures (OEM) for the correct procedure.
Illustration 1 g03360850
If the OEM driven equipment has not been installed to the auxiliary drive, remove bolts (1). Remove cover plate (2) and remove O-ring seal (3) (not shown).
Illustration 2 g03431636
Remove circlip (9) from housing (4).
Remove gear assembly (6) from housing (4).
If necessary, follow Step 5.a through Step 5.c in order to disassemble gear assembly (6).
Remove circlip (8) from gear assembly (6).
Use Tooling (A) in order to remove bearing (7) from gear (6).
Use a suitable tool in order to remove bearing (5) from housing (4). Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
B 7M-7456 Bearing Mount Compound -
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 3 g03431639
Apply a small continuous bead of Tooling (B) to outer Surface (X) of bearing (5).
Use a suitable tool in order to install bearing (5) to housing (4). Remove any excess bearing mount compound.
Illustration 4 g03431658
Illustration 5 g03431659
If necessary, follow Step 3.a through Step 3.g in order to assemble bearing (7) onto gear (6).
Inspect the condition of the teeth and the splines of gear (6) for wear and damage. Inspect bearing (7) circlip (8) and circlip (9).
Inspect the bore in housing (4) for damage. If necessary, replace the front housing. Refer to Disassembly and Assembly, "Housing (Front) - Remove" and Disassembly and Assembly, "Housing (Front) - Install" for the correct procedure.
Apply a small continuous bead of Tooling (B) to inner Surface (Y) of bearing (7). Place the inner race of bearing (7) onto a suitable support. Press the shaft of gear (6) into bearing (7) until the shoulder of the gear is against the bearing. Remove any excess bearing mount compound.
Install circlip (8) into the groove in gear (6).
Apply a small continuous bead of Tooling (B) to the outer Surface (Z) of bearing (7)
Install gear assembly (6) to housing (4). Ensure that the shaft of gear (6) is correctly aligned with the bearing in housing (4). Remove any excess bearing mount compound.
Install circlip (9) into the groove in accessory drive housing (4). Ensure that circlip (9) is correctly positioned in the groove.
Ensure that there is tactile backlash between the idler gear and the accessory drive gear.
Illustration 6 g03360850
Install the auxiliary equipment to the accessory drive housing. Refer to the OEM for the correct procedure.
If the OEM driven equipment is not being installed to the auxiliary drive. Install a new O-ring seal (3) (not shown) and
Caterpillar parts catalog:
Parts plate Caterpillar catalog:
4L3527
PLATE-CLUTCH DRIVING
3114, 3116, 3126, 3126B, 3176B, 3176C, 3196, 3304, 3304B, 3306, 3306B, 3406, 3406B, 3406C, 3406E, 3408, 3408C, 3408E, 3412, 3412C, 3412E, 3456, 3508, 3508B, 3508C, 3512, 3512B, 3516, 3516B, 3516C, C-1...
3114, 3116, 3126, 3126B, 3176B, 3176C, 3196, 3304, 3304B, 3306, 3306B, 3406, 3406B, 3406C, 3406E, 3408, 3408C, 3408E, 3412, 3412C, 3412E, 3456, 3508, 3508B, 3508C, 3512, 3512B, 3516, 3516B, 3516C, C-1...
7N7998
PLATE-BLOCK
12G, 12H, 12H ES, 12H NA, 140G, 140H, 140H ES, 140H NA, 143H, 14G, 14H NA, 160G, 160H, 160H ES, 160H NA, 163H NA, 1673C, 235, 235B, 330, 330 L, 3306, 3306B, 3306C, 330B, 330B L, 350, 528B, 530B, 545, ...
12G, 12H, 12H ES, 12H NA, 140G, 140H, 140H ES, 140H NA, 143H, 14G, 14H NA, 160G, 160H, 160H ES, 160H NA, 163H NA, 1673C, 235, 235B, 330, 330 L, 3306, 3306B, 3306C, 330B, 330B L, 350, 528B, 530B, 545, ...
9N2036
PLATE-LOCK
1693, 16G, 245, 245B, 3208, 3306, 3306B, 3406, 3406B, 3408, 3408B, 3408C, 3408E, 3412, 3412C, 3412E, 3508, 3508C, 3512, 3516, 5130, 5230, 589, 615, 615C, 621E, 621F, 623E, 627B, 627E, 627F, 631D, 631E...
1693, 16G, 245, 245B, 3208, 3306, 3306B, 3406, 3406B, 3408, 3408B, 3408C, 3408E, 3412, 3412C, 3412E, 3508, 3508C, 3512, 3516, 5130, 5230, 589, 615, 615C, 621E, 621F, 623E, 627B, 627E, 627F, 631D, 631E...
1W7110
PLATE-FRONT
120G, 130G, 1673C, 235, 330 L, 3304, 3304B, 3306, 3306B, 3306C, 330B, 936F, 973, CB-534, D5H, D6D, D7G, D7H, G3304, G3306, R1300
120G, 130G, 1673C, 235, 330 L, 3304, 3304B, 3306, 3306B, 3306C, 330B, 936F, 973, CB-534, D5H, D6D, D7G, D7H, G3304, G3306, R1300
3T4705
PLATE AS-BRUSH
140G, 14G, 1673C, 225, 235, 245, 3204, 3208, 3304, 3306, 3306B, 3406, 3406B, 3408, 3412, 3508, 3512, 3516, 572G, 621, 627E, 637E, 776, 777, 815B, 826C, 920, 950B, 980C, D5H, D6D, FB221, G3304, G3512, ...
140G, 14G, 1673C, 225, 235, 245, 3204, 3208, 3304, 3306, 3306B, 3406, 3406B, 3408, 3412, 3508, 3512, 3516, 572G, 621, 627E, 637E, 776, 777, 815B, 826C, 920, 950B, 980C, D5H, D6D, FB221, G3304, G3512, ...
5N4504
PLATE-PORT
3408, 3408C, 3412, 3412C, 3412D, 3412E, 3508, 3508B, 3508C, 3512, 3512B, 3516B
3408, 3408C, 3412, 3412C, 3412D, 3412E, 3508, 3508B, 3508C, 3512, 3512B, 3516B
6N7962
PLATE AS-BACKING
1693, 245, 3406, 3406B, 3408, 3408B, 3408C, 3408E, 3412, 3412C, 3412E, 3508, 3512, 3516, 5130, 5230, 589, 594H, 631D, 631E, 633E II, 637E, 657E, 69D, 769C, 769D, 771D, 776C, 777B, 789B, 826C, 834B, 83...
1693, 245, 3406, 3406B, 3408, 3408B, 3408C, 3408E, 3412, 3412C, 3412E, 3508, 3512, 3516, 5130, 5230, 589, 594H, 631D, 631E, 633E II, 637E, 657E, 69D, 769C, 769D, 771D, 776C, 777B, 789B, 826C, 834B, 83...
6N7540
PLATE-CYLINDER END
3412, 772, 777, D348, D379B, G379, G399
3412, 772, 777, D348, D379B, G379, G399
5N8367
PLATE-REAR END
3412, 3412C, 3412D, 3412E, 3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B, 3516C, 3606, 3608, 3612, 3616, 3618, 5230, 5230B, 776C, 776D, 777D, 784B, 784C, 785, 785B, 785C, 785D, 789B, 789C, 793B,...
3412, 3412C, 3412D, 3412E, 3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B, 3516C, 3606, 3608, 3612, 3616, 3618, 5230, 5230B, 776C, 776D, 777D, 784B, 784C, 785, 785B, 785C, 785D, 789B, 789C, 793B,...
7M0330
PLATE AS-BRUSH
16, 1693, 245, 3406, 3408, 3412, 3508B, 3512, 594, 621, 627, 631C, 631D, 633C, 633D, 637D, 651, 651E, 657B, 657E, 769C, 772, 824B, 966D, 977K, 988, 988B, 992C, D10, D342, D342C, D348, D379A, D379B, D3...
16, 1693, 245, 3406, 3408, 3412, 3508B, 3512, 594, 621, 627, 631C, 631D, 633C, 633D, 637D, 651, 651E, 657B, 657E, 769C, 772, 824B, 966D, 977K, 988, 988B, 992C, D10, D342, D342C, D348, D379A, D379B, D3...
3N4862
PLATE-WEAR
3406, 3406B, 3406C, D353C, G3406
3406, 3406B, 3406C, D353C, G3406
6N5482
PLATE-FRICTION
120G, 12G, 130G, 140G, 14G, 1673C, 215, 225, 3304, 3306, 518, 637D, 941, 955L, D4D, D4E, D5, D5B, D6C, D6D, D7F, D7G
120G, 12G, 130G, 140G, 14G, 1673C, 215, 225, 3304, 3306, 518, 637D, 941, 955L, D4D, D4E, D5, D5B, D6C, D6D, D7F, D7G
4H0003
PLATE
3304, 3406, D342C, D353C, D375D, D379A, D397D, G379
3304, 3406, D342C, D353C, D375D, D379A, D397D, G379
5L5985
PLATE
D379, D379A, D398, G379, G398
D379, D379A, D398, G379, G398
4L3364
PLATE
D379, D379A, D398, D398A, D399, G379
D379, D379A, D398, D398A, D399, G379
8F4102
PLATE
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 120M 2, 12E, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 140M ...
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 120M 2, 12E, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 140M ...
5L8938
PLATE
3192, 7251, 7261
3192, 7251, 7261
8L8536
PLATE
3192
3192
4M4418
PLATE ASSEM.
D337F, D342C, D343, D8H
D337F, D342C, D343, D8H
6L9293
PLATE
D342, D342C, G342C
D342, D342C, G342C
1N8425
PLATE
D342, D342C
D342, D342C
5S7612
PLATE
120B, 120G, 140B, 1673C, 225, 3304, 3306, 518, 637D, 941, 950, 966C, D4D, D5, D6C, D7F, G3304, G3306
120B, 120G, 140B, 1673C, 225, 3304, 3306, 518, 637D, 941, 950, 966C, D4D, D5, D6C, D7F, G3304, G3306
4M0073
PLATE ASSEM.
657, 769, 834, 988, D343, G343
657, 769, 834, 988, D343, G343
5L8934
PLATE ASSEM.
D343
D343