PLATE 7M0322 - Caterpillar

Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Illustration 1 g06059445
Place a suitable container below engine oil pan (7). Remove drain plug (8) and drain the engine lubricating oil. Refer to Operation and Maintenance Manual, "Engine Oil and Filter - Change" for correct procedure.
Remove O-ring seal (9) (not shown) from drain plug (8).
If necessary, remove the assembly of the dipstick tube. Follow Step 3.a through Step 3.c in order to remove dipstick tube (1) from the engine oil pan (7).
Remove bolt (2) and bolt (3).
Loosen nut (4) and remove tube assembly (1).Note: Identify the position and orientation of the tube assembly.
Remove O-ring seal (5) and seal (6) from tube assembly (1).
Illustration 2 g06060098
Remove bolt (11) and position hose assembly (12) out of the way.
Support the assembly of engine oil pan (7). Remove bolts (10).
Remove engine oil pan (7) and remove the gasket.Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Loctite 5900 -
B - Loctite 243 -
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Ensure that the wiring harness assembly is correctly routed and the cable straps are not over tightened. Over tightening of the cable straps will damage the wiring harness and the convoluting.
Ensure that the gasket faces of the cylinder block and the engine oil pan are clean and free from damage.
Illustration 3 g02476000
Illustration 4 g02475999
Apply a bead of Tooling (A) to Positions (Y) on the cylinder block.Note: If the bridge piece for the cylinder block has just been installed, the engine oil pan must be installed before Tooling (A) has cured.
Illustration 5 g06060098
Illustration 6 g02476166
Position the new gasket onto engine oil pan (7).
Install the assembly of engine oil pan (7) to the cylinder block.
Install new bolts (10) in Position (Z) hand tight.
Install remaining bolts (10).
Tighten bolts (10) to

Parts plate Caterpillar catalog:

4L4653 PLATE-THRUST
D379A, D379B, D398A, D398B, D399, G379, G398, G399

7M9919 PLATE (Lock)
12E, 1673, 1673B, 1676, 621, 641, 641B, 657, 657B, 666, 666B, 772, 773, 824, 955H, 977H, 980, D330A, D333A, D333B, D336, D342, D342C, D348, D349, D353C, D379, D379A, D379B, D398, D398A, D398B, D399, G...

1S9172 PLATE
16, 1693, 3406, 594, 631C, 657, 657B, 666, 769, 777, 824B, 826B, 834, 983, 988, 992, D342C, D343, D348, D8H, D9G, D9H, G343

9M8918 PLATE ASSEM.
16, 1693, 3406, 594, 631C, 657, 657B, 666, 769, 777, 824B, 826B, 834, 983, 988, 992, D342C, D343, D348, D8H, D9G, D9H, G343

7M9888 PLATE
16, 1693, 3406, 594, 631C, 657, 657B, 666, 769, 777, 824B, 826B, 834, 983, 988, 992, D320A, D342C, D343, D348, D4D, D8H, D9G, D9H, G343

9M0385 PLATE
1140, 120G, 120H, 120H ES, 120H NA, 130G, 135H, 135H NA, 1673, 1673B, 1673C, 1693, 3114, 3116, 3208, 3304, 3306, 3406, 3408, 528, 613, 613B, 613C II, 621, 621B, 631C, 637D, 651, 768B, 769, 772, 773, 7...

1S5242 PLATE (warning)
225, 235, 561C, 561D, 571G, 572G, 583K, 594, 594H, 931, 941, 951B, 955H, 955K, 955L, 977H, 977K, 977L, 983, 983B, D3, D4D, D4E, D5, D5B, D6C, D6D, D6D SR, D6E, D6E SR, D6F SR, D6G, D6G SR, D6G2 LGP, D...