PLATE AS 8E2873 - Caterpillar

8E2873 PLATE AS Caterpillar parts 578

Price: query
Add in request price Go to cart

Rating:

Alternative (cross code) number:
CA8E2873
8E-2873
8E2873

Weight: 7 pounds 3 kg.

Buy PLATE AS 8E2873 Caterpillar genuine, new aftermarket tractor parts with delivery
PIPELAYER,

Compatible equipment models: 8E2873:

PIPELAYER 578 Caterpillar

Number on catalog scheme: 5

Caterpillar 8E2873 Parts scheme PLATE AS

For full view, you need register

Information:

Introduction
This instruction describes the following procedures:
Removal procedure for the Conventional Solenoids for the 50MT Starting Motor
Removal procedure for Semi-Solid Link Solenoids for the 50MT Starting Motor
Installation procedure for Semi-Solid Link Solenoids for the 50MT Starting MotorDetermine the type of solenoid that needs to be replaced before you begin the following procedures. Use the number that is stamped on the mounting bracket of the solenoid in order to determine the type of solenoid and the procedure to use for the removal of the solenoid.
Conventional Solenoids that are marked with the number 1115662 or lower
Semi-Solid Link Solenoids with the number 1115714 or higherNote: Before replacing the solenoid, remove the starting motor. Ensure that the starting motor is completely disconnected from the vehicle.
Illustration 1 g01045382
Removal Instructions (Conventional Solenoid)
Note: This procedure is for the removal of Conventional Solenoids that are stamped with the number 1115662 or lower.Note: The fasteners in this procedure are referred to by the size of the wrench that is used rather than the size of the threads.
Remove 19.05 mm (3/4 inch) (1) that is located on the terminal of the solenoid that is labeled "MTR".
Remove the 19.05 mm (3/4 inch) nut (2) at the frame.
Remove the stamped metal connector strap (3) .
Remove the 9.53 mm (3/8 inch) nut (4) from ground terminal "G".
Disconnect the flexible ground cable (5) from the "G" terminal.
For models with a boot clamp (8) , remove the clamp by inserting a screwdriver into the serrated portion of the clamp. Pry upward. Save the clamp in order to reuse the clamp.
Remove four E8 Torx Head screws (7) that mount

Caterpillar parts catalog:

Caterpillar parts catalog
Product:

578 Pipelayer 8HB00001-UP (MACHINE) POWERED BY 3406 Engine

6T-9909: FIREWALL GP » SEBP18870286

Parts plate Caterpillar catalog:

3T9525 PLATE AS-BRUSH
1090, 1190, 1190T, 120M, 120M 2, 1290T, 12M 2, 12M 3, 12M 3 AWD, 1390, 140M, 140M 2, 140M 3, 140M 3 AWD, 14H, 14M, 160M, 160M 2, 160M 3, 160M 3 AWD, 16H NA, 16M, 2290, 235, 235D, 2390, 2391, 245, 2491...

3T0862 PLATE AS-BRUSH
120G, 12G, 130G, 140G, 14G, 160G, 1673C, 16G, 215, 215B, 235, 245, 3176B, 3176C, 3196, 3208, 330 L, 3304, 3304B, 3306, 3306B, 3306C, 3406, 3406B, 3406C, 3406E, 3408, 3408B, 3408C, 3412, 3412C, 3412E, ...

2531752 PLATE-THRUST
16G, 16H NA, 24H, 24M, 3406, 3406B, 3406C, 3406E, 3408, 3408B, 3408C, 3408E, 3412, 3412C, 3412D, 3412E, 3456, 365C, 365C L, 365C L MH, 374D L, 374F L, 375, 375 L, 385B, 385C, 385C FS, 385C L, 385C L M...

1129217 PLATE-THRUST
16G, 16H NA, 24H, 24M, 3406, 3406B, 3406C, 3406E, 3408, 3408B, 3408C, 3408E, 3412, 3412C, 3412D, 3412E, 3456, 365C, 365C L, 365C L MH, 374D L, 374F L, 375, 375 L, 385B, 385C, 385C FS, 385C L, 385C L M...

4N0342 PLATE-CAMSHAFT THRUST
16G, 16H NA, 245, 245D, 24H, 3406, 3406B, 3406C, 3408, 3408B, 3408C, 3408E, 3412, 3412C, 3412D, 3412E, 375, 375 L, 5080, 5110B, 578, 583R, 587R, 589, 621E, 621F, 623E, 623F, 627B, 627E, 627F, 631D, 63...

5S1213 PLATE
120, 120B, 12F, 140, 140B, 14E, 16, 16G, 245, 245B, 245D, 3304B, 3306, 5130, 5130B, 5230, 5230B, 561B, 561C, 572G, 578, 589, 594H, 613, 621, 621B, 621E, 621F, 621R, 623, 623E, 623F, 627, 627B, 627E, 6...

9G8020 PLATE-RETAINER
30/30, 572R, 572R II, 578, 583R, 583T, 587R, 587T, 611, 615, 615C, 814B, 814F, 814F II, 815B, 815F, 815F II, 816F, 816F II, 966D, 966F, 966F II, 966G, 966G II, 970F, 972G, 972G II, 972H, 972K, 980C, 9...