PLATE 8M5075 - Caterpillar

(1) Torque for three studs to hold the water pump ... 27 4 N m (20 3 lb ft)(2) Plug (two on front and two on rear).(3) Length of dowels (four) out of the block face ... 18.5 0.5 mm (.73 .02 in)(4) Thickness of the gasket between the cylinder block and top plates ... 0.21 0.03 mm (.008 .001 in)(5) Thickness of the top plates ... 8.585 0.025 mm (.3380 .0010 in)(6) Make reference to Cylinder Liner Projection in the Systems Operation, Testing & Adjusting, for the height of the liner.(7) Bore in the block for the camshaft bearings (seven bores) ... 76.835 0.018 mm (3.0250 .0007 in)(8) Torque for one plug on front and two on rear of the block ... 80 15 N m (60 11 lb ft)Put 5P3413 Pipe Sealant on the threads of the plug.(9) Bore in the block for the main bearings: Standard, original size (new) ... 129.891 0.013 mm (5.1138 .0005 in)0.64 mm (.025 in) larger than original size ... 130.526 0.013 mm (5.1388 .0005 in)(10) Projection of dowels (four) out of the front and rear faces of the block ... 19.0 0.5 mm (.75 .02 in)(11) Width of slot for bearing cap ... 215.900 0.013 mm (8.5000 .0005 in) Width of bearing cap ... 215.900 0.013 mm (8.5000 .0005 in)Press fit between sides of the main bearing cap and the cylinder block ... 0.026 mm (.0010 in) tight to ... 0.026 mm (.0010 in) loose(12) Torque for the bolts that hold the piston cooling tubes ... 25 7 N m (18 5 lb ft)(13) Torque for the bolts that hold the caps for the main bearings:Install the main bearing caps with the marks (arrow) toward the front of the engine. Each cap has a number on the bottom and must be installed in the same position as the correct number on the left side of the block pan rail.a. Tighten the bolts on left (tab) side to ... 258 14 N m (190 10 lb ft)b. Tighten the bolts on right side to ... 258 14 N m (190 10 lb ft)c. Put a mark on each bolt and cap.d. Tighten the bolts on right side, from the mark ... 120 5 degreese. Tighten the bolts on left (tab) side, from the mark ... 120 5 degrees (14) Dimension (new) from the centerline of crankshaft bearing bore to top of block (top deck) ... 419.10 0.15 mm (16.500 .006 in)(15) Dimension (new) from centerline of crankshaft bearing bore to bottom of block (pan rails) ... 165.10 0.10 mm (6.500 .004 in)
Right Side Of Engine(16) Plug. Two plugs (one located at front and the other located

Parts plate Caterpillar catalog:

4N4377 PLATE-REAR END
3176B, 3176C, 3196, 3304, 3304B, 3306, 3306B, 3406, 3406B, 3406C, 3406E, 3408, 3408C, 3408E, 3456, 768B, 769, C-10, C-12, C-15, C-16, C-9, C11, C12, C13, C15, C18, C9, CX31-C13I, CX31-C15I, CX31-C9I, ...

4N4382 PLATE-FRONT END
3176B, 3176C, 3196, 3304, 3304B, 3306, 3306B, 3406, 3406B, 3406C, 3406E, 3408, 3408C, 3408E, 3456, 768B, 769, C-10, C-12, C-15, C-16, C-9, C11, C12, C13, C15, C18, C9, CX31-C13I, CX31-C15I, CX31-C9I, ...

6H5139 PLATE-PRESSURE
120G, 12F, 12G, 130G, 140, 141, 14E, 14G, 153, 16, 163, 16G, 172, 173B, 183, 183B, 184, 191, 193, 30/30, 416, 416B, 426B, 428, 428B, 438B, 446, 46, 508, 515, 517, 518, 525, 525D, 527, 528, 535D, 545D,...

6N7540 PLATE-CYLINDER END
3412, 772, 777, D348, D379B, G379, G399

7M9919 PLATE (Lock)
12E, 1673, 1673B, 1676, 621, 641, 641B, 657, 657B, 666, 666B, 772, 773, 824, 955H, 977H, 980, D330A, D333A, D333B, D336, D342, D342C, D348, D349, D353C, D379, D379A, D379B, D398, D398A, D398B, D399, G...

8F4102 PLATE
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 120M 2, 12E, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 140M ...

1S9172 PLATE
16, 1693, 3406, 594, 631C, 657, 657B, 666, 769, 777, 824B, 826B, 834, 983, 988, 992, D342C, D343, D348, D8H, D9G, D9H, G343

7M9888 PLATE
16, 1693, 3406, 594, 631C, 657, 657B, 666, 769, 777, 824B, 826B, 834, 983, 988, 992, D320A, D342C, D343, D348, D4D, D8H, D9G, D9H, G343

4J3816 PLATE
215, 215B, 225, 229, 235, 235B, 235D, 245, 245B, 24H, 24M, 5110B, 5130, 5130B, 5230, 5230B, 528, 589, 621, 621B, 621E, 621F, 621G, 621R, 623E, 623F, 623G, 627B, 627E, 627F, 627G, 631C, 631E, 631G, 633...