AVSPARE.COM
parts catalog

PLATE, BOTTOM B59106211 - Caterpillar



B59106211 PLATE, BOTTOM Caterpillar parts EL240 PLATE
Rating:
82
Alternative (cross code) number:
CAB59106211
B5910-6211
B59106211
Caterpillar B59106211 PLATE, BOTTOM

Buy PLATE, BOTTOM B59106211 Caterpillar genuine, new aftermarket tractor parts with delivery
EXCAVATOR,

Compatible equipment models: B59106211:

EXCAVATOR  EL240   Caterpillar
Number on catalog scheme: 3
  
  For full view, you need register

Information:


Illustration 3 g00705073
Install the seals on the shaft (31). Position the shift lever assembly (28) into the shift lever housing. Use a 1P-1855 Retaining Ring Pliers to install the shaft (31) and the snap ring .
Install the O-ring seal and the gasket onto the shift lever housing. Set the shift lever housing assembly (29) onto the starting motor housing in the correct position. Install the seven bolts and tighten the bolts (30) to a torque of 12.2 2.7 N m (108 24 lb in).
Illustration 4 g00704879
Use 5P-0960 Molybdenum Grease to lubricate the armature assembly bushing areas. Do not grease the armature core or the commutator.
Put the pinion drive assembly (27) into position in the fork of the shift lever. Put the spacer on the armature assembly (26). Install the armature assembly (26) into the starting motor housing and the shift lever housing. Slide the armature assembly (26) into the pinion drive assembly (27).
Illustration 5 g00704875
Use a 1P-0510 Driver Gp to install the bushing (25) into the pinion drive housing (23).
Illustration 6 g00704870
Slide the pinion drive housing assembly (23) onto the shift lever housing in the correct position. Install the six screws (24) and tighten to a torque of 20 3 N m (178 27 lb in).
Illustration 7 g00704856
Position the insulator (22), the plate (21) and the brush holders onto the brush plate assembly. Install the screws (20) and tighten the screws .
Illustration 8 g00704842
Use a 1P-0510 Driver Gp in order to install the bushing (19) into the rear frame assembly (14) .
Illustration 9 g00705811
Install the O-ring seal (18) onto the rear frame assembly. Position the gasket onto the brush plate assembly (16). Put the washers and the insulator on the negative terminal.
Position brush plate assembly (16) onto the rear frame and install the three screws. Install the negative terminal insulator, the washers and the nut. Tighten the nut to a torque of 30 3 N m (22 2 lb ft).
Install the brushes (15) with the brush springs against the side of each brush. Tighten the lead screw for the brushes to a torque of 2.9 1.0 N m (26 8 lb in).
Illustration 10 g00705821
Put the washer onto the armature assembly. Position the rear frame assembly (14) over the commutator. Push the brushes (15) into the holders so that the springs are on top of the brushes.
Put the rear frame assembly against the starting motor housing in the correct position. Install the six bolts and tighten the bolts to a torque of 12.2 2.7 N m (108 24 lb in). Connect the wire assembly to the negative terminal on the end frame assembly.
Illustration 11 g00705835
Connect the three field winding leads (38) to the brush plate assembly. Tighten the screws to a torque of 2.9 1.0 N m (26 8 lb in). Install the three gaskets and plugs on the starting motor housing.
Illustration 12 g00706331
Install the washer, the retainer, the boot, the spring, the retainer and the ring onto the plunger.
Position the plunger assembly

Caterpillar parts catalog:

Caterpillar parts catalog
SUPPLEMENT FOR EL240 HYDRAULIC EXCAVATOR /60FT-LONG REACH FRON/ 4JF00001-UP (MACHINE)


Parts plate Caterpillar catalog:

1R8628 PLATE
E110B, E120B, E140, E200B, E240C, E300B, E70B, EL240B
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.