3793172 PLENUM Caterpillar parts
824K, 825K, 826K, 834K, 836K, 988K, CX31-C18I
Rating:
Alternative (cross code) number:
CA3793172
379-3172
3793172
CA3793172
379-3172
3793172
Weight: 6 pounds 2 kg.
LANDFILL COMPACTOR, WHEEL LOADER,
Compatible equipment models: 3793172:
Information:
Introduction
The problem that is identified below does not have a known permanent solution. Until a permanent solution is known, use the solution that is identified below.Problem
The functions of the machine's Electronic Control Module (ECM) are disabled during the flashing process. The engine ECM does not receive a throttle signal during the process. This causes the engine ECM to generate a false 91-8 Throttle Position Sensor abnormal frequency, pulse width, or period diagnostic code.Occasionally, the machine ECM also generates a false diagnostic code after the flashing process. For example, a false 2300-9 Switch Panel abnormal update rate might be generated.Solution
After flashing new software into a machine ECM, cycle the machine's keyswitch to the Off position for a minimum of one minute. Cycle the keyswitch before you operate the machine. The false diagnostic code will disappear after the keyswitch is cycled.Verify that the diagnostic code has been erased. If a code continues to be generated, troubleshoot the code according to the appropriate Troubleshooting manual.
The problem that is identified below does not have a known permanent solution. Until a permanent solution is known, use the solution that is identified below.Problem
The functions of the machine's Electronic Control Module (ECM) are disabled during the flashing process. The engine ECM does not receive a throttle signal during the process. This causes the engine ECM to generate a false 91-8 Throttle Position Sensor abnormal frequency, pulse width, or period diagnostic code.Occasionally, the machine ECM also generates a false diagnostic code after the flashing process. For example, a false 2300-9 Switch Panel abnormal update rate might be generated.Solution
After flashing new software into a machine ECM, cycle the machine's keyswitch to the Off position for a minimum of one minute. Cycle the keyswitch before you operate the machine. The false diagnostic code will disappear after the keyswitch is cycled.Verify that the diagnostic code has been erased. If a code continues to be generated, troubleshoot the code according to the appropriate Troubleshooting manual.
Caterpillar parts catalog:
Parts plenum Caterpillar catalog:
3362214
PLENUM
CX31-C13I
CX31-C13I
3378148
PLENUM
980K, 980K HLG, C13, C15, CX31-C13I
980K, 980K HLG, C13, C15, CX31-C13I
4363690
PLENUM AS
C13, C15
C13, C15
2305538
PLENUM AS
G3412
G3412
1741147
PLENUM AS
TH220B, TH330B, TH340B, TH350B, TH355B, TH460B, TH560B, TH580B
TH220B, TH330B, TH340B, TH350B, TH355B, TH460B, TH560B, TH580B
1199627
PLENUM AS
35, 45, 55
35, 45, 55
3329026
PLENUM
D6T LGP, D6T XL
D6T LGP, D6T XL
9C1863
PLENUM AS
227, 245
227, 245
7V7400
PLENUM ASSEM.
227, 245
227, 245
4352948
PLENUM
305.5E, 308E, 308E2 CR
305.5E, 308E, 308E2 CR
4352943
PLENUM
305.5E, 308E, 308E2 CR
305.5E, 308E, 308E2 CR