0691745 PLUG Caterpillar parts
AP-1000, AP-1000B, AP-1055B, AP-650B, AP-800C, AP-800D, AP-900B, BG-225B, BG-225C, BG-2455C, BG-245C, PM-465, PM-565, RM-350B, RR-250, SM-350, SS-250
Rating:
Alternative (cross code) number:
CA0691745
069-1745
0691745
CA0691745
069-1745
0691745
Weight: 0.010 pounds 0 kg.
ASPHALT PAVER, STABILIZER MIXER,
Compatible equipment models: 0691745:
Number on catalog scheme:
49
For full view, you need register
Information:
Introduction
This procedure is utilized to adjust the steering axle stop for an axle steering joint assembly. The axle housing contains a projection which includes a contact surface disposed for limiting the rotation of the steering knuckle.Required Tools
Table 1
Required Tools
Item Qty Part Number Description
F1 1 Protractor
F2 1 FT-2294 Alignment Bar
F3 1 Square
1 FT-2295 Wrench ( 75 mm)
1 FT-2296 Wrench ( 41 mm)
1 Caliper Machine Preparation
Clear all personnel from the machine and from the area around the machine.
Start the engine.
Illustration 1 g02449876
Engine speed dial
Set the engine speed dial at "10".
Lower the left console.
Position the machine on level ground. Check the visibility and adjust the mirrors for the best vision close to the machine.
Fully depress the service brake pedal until the service brake pedal locks mechanically.
Lower the stabilizers and the blade tip.
Fully extend the bucket cylinder and place the bucket on the ground.
Stop the engine.
Release the pressure in the hydraulic system. Note: Refer to Testing and Adjusting, "System Pressure - Release".
Raise the left console. Test Procedure
Personal injury or death can result from sudden machine movement.Sudden movement of the machine can cause injury to persons on or near the machine.To prevent injury or death, make sure that the area around the machine is clear of personnel and obstructions before operating the machine.
Illustration 2 g02416939
Steering lock
(F1) Protractor
(F2) FT-2294 Alignment bar
(F3) Square
(1) Hub face
Turn the steering wheel until the steering wheel stops. Turn the steering wheel to the right in order to check the right wheel. Turn the steering wheel to the left in order to check the left wheel.
Place square (F3) on hub face (1). Use protractor (F2) to measure the angle between square (F3) and alignment bar (3). The angle should be 35 degrees. Note: The angle relates to the inside wheel. The outside wheel has an angle of 28 degrees (standard tires).Adjust Procedure
Illustration 3 g02416940
(A) 35 degrees
(B) 28 degrees
(2) Adjustment bolt
Loosen the locknut on adjustment bolt (2). Turn adjustment bolt (2) until the correct angle is achieved.
Tighten the locknut on adjustment bolt (2) to the specified torque.
Remove the tooling.
Repeat this procedure for the opposite wheel.
This procedure is utilized to adjust the steering axle stop for an axle steering joint assembly. The axle housing contains a projection which includes a contact surface disposed for limiting the rotation of the steering knuckle.Required Tools
Table 1
Required Tools
Item Qty Part Number Description
F1 1 Protractor
F2 1 FT-2294 Alignment Bar
F3 1 Square
1 FT-2295 Wrench ( 75 mm)
1 FT-2296 Wrench ( 41 mm)
1 Caliper Machine Preparation
Clear all personnel from the machine and from the area around the machine.
Start the engine.
Illustration 1 g02449876
Engine speed dial
Set the engine speed dial at "10".
Lower the left console.
Position the machine on level ground. Check the visibility and adjust the mirrors for the best vision close to the machine.
Fully depress the service brake pedal until the service brake pedal locks mechanically.
Lower the stabilizers and the blade tip.
Fully extend the bucket cylinder and place the bucket on the ground.
Stop the engine.
Release the pressure in the hydraulic system. Note: Refer to Testing and Adjusting, "System Pressure - Release".
Raise the left console. Test Procedure
Personal injury or death can result from sudden machine movement.Sudden movement of the machine can cause injury to persons on or near the machine.To prevent injury or death, make sure that the area around the machine is clear of personnel and obstructions before operating the machine.
Illustration 2 g02416939
Steering lock
(F1) Protractor
(F2) FT-2294 Alignment bar
(F3) Square
(1) Hub face
Turn the steering wheel until the steering wheel stops. Turn the steering wheel to the right in order to check the right wheel. Turn the steering wheel to the left in order to check the left wheel.
Place square (F3) on hub face (1). Use protractor (F2) to measure the angle between square (F3) and alignment bar (3). The angle should be 35 degrees. Note: The angle relates to the inside wheel. The outside wheel has an angle of 28 degrees (standard tires).Adjust Procedure
Illustration 3 g02416940
(A) 35 degrees
(B) 28 degrees
(2) Adjustment bolt
Loosen the locknut on adjustment bolt (2). Turn adjustment bolt (2) until the correct angle is achieved.
Tighten the locknut on adjustment bolt (2) to the specified torque.
Remove the tooling.
Repeat this procedure for the opposite wheel.
Caterpillar parts catalog:
Parts plug Caterpillar catalog:
1090, 1190, 1190T, 1290T, 130G, 1390, 140, 1693, 173B, 183B, 205B, 211B, 214B, 215, 215B, 215D, 219D, 225, 225D, 227, 229, 2290, 231D, 235, 235B, 235C, 235D, 236D, 2384C, 2390, 2391, 242D, 245, 245B, ...
1090, 1190, 1190T, 120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 120M 2, 1290T, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 135H, 135H NA, 140, 140G, 140H, 140H ES, 140H NA,...
120M, 120M 2, 12M, 12M 2, 12M 3, 12M 3 AWD, 140M, 140M 2, 140M 3, 140M 3 AWD, 14G, 14M, 160M, 160M 2, 160M 3, 160M 3 AWD, 1673C, 1693, 16M, 3114, 3116, 3204, 3208, 3304, 3304B, 3306, 3306B, 3306C, 340...
1140, 1145, 1150, 1160, 120G, 140B, 140G, 14G, 1673, 1673B, 1673C, 1674, 1676, 1693, 16G, 215, 215B, 215C, 215D, 225, 225D, 229D, 231D, 235, 235B, 235C, 245, 245B, 30/30, 303, 3114, 3116, 3126, 3126B,...
120G, 12G, 12H, 12H ES, 12H NA, 130G, 140G, 140H, 140H ES, 140H NA, 143H, 14G, 14H, 14H NA, 160G, 160H, 160H ES, 160H NA, 163H, 163H NA, 1673C, 16G, 16H, 16H NA, 215B, 225D, 235B, 235C, 235D, 245B, 24...
140, 141, 16, 163, 1673, 1673B, 1673C, 1674, 1693, 191, 3181, 3192, 3304, 3304B, 3306, 3306B, 3406, 3406B, 3406C, 3406E, 3408, 3408C, 3408E, 3412, 3412C, 3412E, 3508, 3508B, 3508C, 3512, 3512B, 3512C,...
1090, 1140, 1150, 1160, 1190, 1190T, 120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 120M 2, 1290T, 12E, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 135H, 135H NA, 1390, 140G,...
10-20B, 1090, 1190, 1190T, 120H, 120K, 120K 2, 120M, 120M 2, 1290T, 12H, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 135H, 1390, 140H, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 143H, 14H, 14M, 160H, 160K...
16G, 16H NA, 24H, 24M, 3056, 3406, 3406B, 3406C, 3406E, 3408, 3408B, 3408C, 3408E, 3412, 3412C, 3412D, 3412E, 3456, 365C, 365C L, 365C L MH, 374D L, 374F L, 375, 375 L, 385B, 385C, 385C FS, 385C L, 38...
1546028
PLUG
AP-1000, AP-1000B
AP-1000, AP-1000B
1554047
PLUG-PIPE
AP-1000, AP-1000B, PM-465
AP-1000, AP-1000B, PM-465
6R0704
PLUG-PLASTIC
AP-1000, AP-1000B, AP-650B, AP-800C, AP-800D, BG-225B, BG-225C, BG-245C, CB-434
AP-1000, AP-1000B, AP-650B, AP-800C, AP-800D, BG-225B, BG-225C, BG-245C, CB-434
1G8448
PLUG-ORIFICE
AP-1000, AP-1000B, AP-650B, AP-800C, AP-800D, BG-225B, BG-225C, BG-245C, CB-534B, CB-534C, CB-535B, CB-634, CB-634C, RM-350B, SM-350
AP-1000, AP-1000B, AP-650B, AP-800C, AP-800D, BG-225B, BG-225C, BG-245C, CB-534B, CB-534C, CB-535B, CB-634, CB-634C, RM-350B, SM-350
1G8433
PLUG
AP-1000, AP-1000B, AP-650B, AP-800C, AP-800D, BG-225B, BG-225C, BG-245C, CB-534B, CB-534C, CB-535B, CB-634, CB-634C, RM-350B, SM-350
AP-1000, AP-1000B, AP-650B, AP-800C, AP-800D, BG-225B, BG-225C, BG-245C, CB-534B, CB-534C, CB-535B, CB-634, CB-634C, RM-350B, SM-350
5E8231
PLUG
AP-1000, AP-800, AP-800C, AP-800D, BG-225B, CB-434
AP-1000, AP-800, AP-800C, AP-800D, BG-225B, CB-434
1G7381
PLUG-CHARGE RELIEF
AP-200B, CS-531
AP-200B, CS-531
1G7293
PLUG-PORT
AP-1000B, AP-1055B, AP-200B, AP-655C, AP-900B, BG-2455C, BG-245C, PM-465
AP-1000B, AP-1055B, AP-200B, AP-655C, AP-900B, BG-2455C, BG-245C, PM-465
0980563
PLUG
RM-250C, RM-300, RR-250, RR-250B, SS-250
RM-250C, RM-300, RR-250, RR-250B, SS-250
AP-1000, AP-1000B, AP-1055B, AP-900B, BG-2455C, CP-433C, CP-433E, CP-44, CP-533E, CP-54B, CP-56, CP-573E, CP-64, CP-663E, CP-68B, CP-74B, CP-76, CS-323C, CS-423E, CS-431C, CS-433C, CS-433E, CS-44, CS-...
1613933
PLUG
AP-1000
AP-1000
1C4388
PLUG-MAGNETIC
AP-1000, AP-1000B, AP-1055B, AP-800C, AP-800D, BG-225B, BG-2455C, CB-534B, CB-534C, CB-535B, CB-634, CB-634C, CS-323C, CS-573C, CS-583, CS-583C, PM-565, PR-105, PR-450, PR-450C
AP-1000, AP-1000B, AP-1055B, AP-800C, AP-800D, BG-225B, BG-2455C, CB-534B, CB-534C, CB-535B, CB-634, CB-634C, CS-323C, CS-573C, CS-583, CS-583C, PM-565, PR-105, PR-450, PR-450C