1311845 PLUG-HEX SOCKET Caterpillar parts
120H, 135H, 30/30, 3116, 3126, 3126B, 3126E, 322C, 322C FM, 325C, 325C FM, 561N, 570B, 580B, 938G II, 950G II, 953C, 962G II, 963C, C7, D5N, D6N, DEUCE, IT38G II, IT62G II, M325C MH, SPP101
Rating:
Alternative (cross code) number:
CA1311845
131-1845
1311845
CA1311845
131-1845
1311845
Weight: 0.01 pounds 0 kg.
Information:
DASH SIZE
000000000002
FLANGE DIAMETER
11
mm
HEX SIZE
3.18
mm
OVERALL LENGTH
9.5
mm
SHOULDER LENGTH
7.5
mm
STANDARD SEAL PART NUMBER
4J7533
THREAD SIZE
.31-24
EXCAVATOR, WHEELED EXCAVATOR,
Compatible equipment models: 1311845:
Number on catalog scheme:
9
For full view, you need register
Information:
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 5P-3931 Anti-Seize Compound -
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Clamp assemblies MUST only be used once. Discard all clamp assemblies after use.
Bellows assemblies MUST only be used once. Discard all bellows assemblies after use.
Illustration 1 g01351521
Attach a suitable lifting device to turbocharger (3) . The weight of turbocharger (3) is approximately 135 kg (300 lb).
Position turbocharger (3) on the mounting bracket. Apply Tooling (A) to the threads of bolts (5) . Install bolts (5) . Do not tighten bolts (5) at this time.
Install tube assembly (4) . Connect tube (9) , tube assembly (8) , and tube assembly (6) .Note: Ensure that the bellows assembly is in the proper orientation during installation. The spacing between the ridges of the bellows assembly should be equal.
Apply Tooling (A) to the threads, the bearing surfaces, and the inner surface of clamp assembly (7) . Install new bellows assembly (10) , bolts (11) , and new clamp assembly (7) . Tighten clamp assembly (7) to a torque of 10 1 N m (90 9 lb in). Lightly tap around the diameter of the clamp assembly with a soft hammer. Tighten clamp assembly (7) to a torque of 10 1 N m (90 9 lb in).
Illustration 2 g01351417
Note: Ensure that the bellows assembly is in the proper orientation during installation. The direction of flow arrow must point in the correct direction. The spacing between the ridges of the bellows assembly should be equal.
Apply Tooling (A) to the threads, the bearing surfaces, and the inner surface of clamp assemblies (2) and clamp assemblies (1) . Install new bellows assemblies, new clamp assemblies (2) , and new clamp assemblies (1) on turbocharger (3) . Tighten clamp assemblies (2) and clamp assemblies (1) to a torque of 7.5 1.0 N m (65 9 lb in). Lightly tap around the diameter of the clamp assemblies with a soft hammer. Tighten clamp assemblies (2) and clamp assemblies (1) to a torque of 7.5 1.0 N m (65 9 lb in).
Tighten the bolts that attach turbocharger (3) to the standard torque.
Install the air cleaner.
Fill the cooling system with coolant. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change".
Table 1
Required Tools
Tool Part Number Part Description Qty
A 5P-3931 Anti-Seize Compound -
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Clamp assemblies MUST only be used once. Discard all clamp assemblies after use.
Bellows assemblies MUST only be used once. Discard all bellows assemblies after use.
Illustration 1 g01351521
Attach a suitable lifting device to turbocharger (3) . The weight of turbocharger (3) is approximately 135 kg (300 lb).
Position turbocharger (3) on the mounting bracket. Apply Tooling (A) to the threads of bolts (5) . Install bolts (5) . Do not tighten bolts (5) at this time.
Install tube assembly (4) . Connect tube (9) , tube assembly (8) , and tube assembly (6) .Note: Ensure that the bellows assembly is in the proper orientation during installation. The spacing between the ridges of the bellows assembly should be equal.
Apply Tooling (A) to the threads, the bearing surfaces, and the inner surface of clamp assembly (7) . Install new bellows assembly (10) , bolts (11) , and new clamp assembly (7) . Tighten clamp assembly (7) to a torque of 10 1 N m (90 9 lb in). Lightly tap around the diameter of the clamp assembly with a soft hammer. Tighten clamp assembly (7) to a torque of 10 1 N m (90 9 lb in).
Illustration 2 g01351417
Note: Ensure that the bellows assembly is in the proper orientation during installation. The direction of flow arrow must point in the correct direction. The spacing between the ridges of the bellows assembly should be equal.
Apply Tooling (A) to the threads, the bearing surfaces, and the inner surface of clamp assemblies (2) and clamp assemblies (1) . Install new bellows assemblies, new clamp assemblies (2) , and new clamp assemblies (1) on turbocharger (3) . Tighten clamp assemblies (2) and clamp assemblies (1) to a torque of 7.5 1.0 N m (65 9 lb in). Lightly tap around the diameter of the clamp assemblies with a soft hammer. Tighten clamp assemblies (2) and clamp assemblies (1) to a torque of 7.5 1.0 N m (65 9 lb in).
Tighten the bolts that attach turbocharger (3) to the standard torque.
Install the air cleaner.
Fill the cooling system with coolant. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change".
Cat SIS web machinery list:
Parts plug Caterpillar catalog:
120K, 120K 2, 12H, 12K, 12M, 140K 2, 140M, 160K, 160M, 3126, 3126B, 3126E, 322C, 324D, 325C, 329D L, 330C, 330C FM, 330C L, 330C MH, 330D, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 525C, 535C, ...
10 FT, 215, 225, 245, 245B, 3126B, 8 FT, 950, C7, R1300G, R1600, R1600G
1690117
PLUG-TAPER
3412
3412
3320971
PLUG AS
3512B, 3512C, 3516, 3516B, 3516C, 793F, 793F CMD, 793F OEM, 793F-XQ, 795F AC, 797, 797B, 797F, C175-16, C175-20
3512B, 3512C, 3516, 3516B, 3516C, 793F, 793F CMD, 793F OEM, 793F-XQ, 795F AC, 797, 797B, 797F, C175-16, C175-20
3512, 3512B, 3512C, 3516, 3516B, 3516C, 793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ, 795F AC, 797, 797B, 797F, C175-16, C175-20
8C4423
PLUG
3512, 3512B, 3512C, 3516, 3516B, 3516C, 793D, 793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ, 795F AC, 795F XQ, 797, 797B, 797F, C175-16, C175-20, G3520B
3512, 3512B, 3512C, 3516, 3516B, 3516C, 793D, 793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ, 795F AC, 795F XQ, 797, 797B, 797F, C175-16, C175-20, G3520B
1947226
PLUG
3034, 3054, 3054B, 3056, C1.5, C2.2, C4.4
3034, 3054, 3054B, 3056, C1.5, C2.2, C4.4
3548322
PLUG
120M, 120M 2, 12M, 2384C, 2470C, 2484C, 2570C, 2670C, 3056, 3056E, 320D GC, 320D L, 320D2, 320D2 GC, 320D2 L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 323D L, 323D2 L, 323E L, 324E, 324E L, 324E LN, ...
120M, 120M 2, 12M, 2384C, 2470C, 2484C, 2570C, 2670C, 3056, 3056E, 320D GC, 320D L, 320D2, 320D2 GC, 320D2 L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 323D L, 323D2 L, 323E L, 324E, 324E L, 324E LN, ...
3638047
PLUG
3054, 3054B, 3056, 3056E, 924G, BB-760, CP-573E, CP-663E, CS-563E, CS-583E, CS-663E, CS-683E, M318C, M318C MH, M322C
3054, 3054B, 3056, 3056E, 924G, BB-760, CP-573E, CP-663E, CS-563E, CS-583E, CS-663E, CS-683E, M318C, M318C MH, M322C
3056, C4.4
6I4682
PLUG
3056, AP-1200
3056, AP-1200
3508, 621F, 621G, 623E, 623F, 623G, 627F, 627G, 627H, 627K, 627K LRC, 631G, 637D, 637E, 637G, 657B, 657G, 773D, 773E, 775D, 775E, 776D, 777, 777D, 784C, 785C, 785D, 789C, 789D, 793C, 793D, AD30, AD45B...