2239259 PLUG GP-WATER LINES Caterpillar parts
C15
Rating:
Alternative (cross code) number:
CA2239259
223-9259
2239259
CA2239259
223-9259
2239259
TRUCK ENGINE,
Compatible equipment models: 2239259:
Number on catalog scheme:
For full view, you need register
Information:
375-4214 Cable As
Illustration 31 g03172840
Extension harness routed inside spiral wrap (45) 375-4214 Cable As Perform the following procedure to install the 375-4214 Cable As (45) :
Route the 375-4214 Cable As (45) through the existing hole from the machine house.Note: This step may already have been carried out previously at the same time as the boom rotation and angle sensor harnesses were fed through the exit.
Route the extension cable along the existing cable (45) towards the hydraulic hose junction plate on the boom.
Use the spiral wrap to bundle the extension cable along with the existing cables (45). Leave the connector accessible at the hydraulic hose junction plate. 361-3002 Sensor Harness As
Illustration 32 g03172842
(46) Hydraulic hose junction plate on boomPerform the following procedure to install the 361-3002 Sensor Harness As :
At the hydraulic hose junction plate, connect the shorter "PWR/SENSOR/CAN" branch of the 361-3002 Sensor Harness As to the "PWR/SENSOR/CAN" of the 375-4214 Cable As .
Illustration 33 g03172843
(47) Mast angle sensor
Route the "MAST TILT SENSOR" branch of the 361-3002 Sensor Harness As along the existing cable towards the mast angle sensor (47). Refer to Illustration 33.
Connect the "MAST TILT SENSOR" branch to the mast angle sensor.
Use the existing spiral wrap to bundle the 361-3002 Sensor Harness As with the existing cable.
Use cable straps to secure the visible 361-3002 Sensor Harness As to the existing hydraulic hoses.Ensure to leave a light service loop at the sensor. Ensure that there is no tension on the connector. 375-4215 Cable As
Perform the following procedure to install the 375-4215 Cable As :
At the hydraulic hose junction plate, connect the 375-4215 Cable As to the 361-3002 Sensor Harness As . Refer to Illustration 32.
Illustration 34 g03172844
(48) Hose collar (49) Spiral wrap around existing cable routed towards mast
Illustration 35 g02552863
Mast passage hole
Route the extension cable along with the existing cable through the hose collar (48) and up through the mast passage hole. Refer to Illustration 34 and Illustration 35.
Route the extension cable with the existing spiral wrap (49) between the hydraulic hose junction plate and the mast passage hole. Refer to Illustration 35.Note: Be sure to observe safe procedures for access. Maintain a three-point contact and/or use a safety harness.
Route the extension cable up towards the top of the mast. Follow the path of existing cables and route through the protective corridor.Use p-clips and cable straps to secure along the mast.
At the base of the mounting bracket, route the connector through the hollow of the base from non-cab side to cab-side of the mast.
Coil excess 375-4215 Cable As below the base of the support bracket. Use cable straps to secure the excess harness to the existing harnesses. 353-8858 Wiring Harness
Perform the following procedure to install the 353-8858 Wiring Harness :
Ensure that the mast is in a lowered position.
Connect the 353-8858 Wiring Harness between the 291-1913 Satellite Receiver As (GNSS, MS990). Ensure the following connections:
Connect the branch labeled "NON-CAB SIDE" to the slave satellite receiver.
Connect the branch labeled "CAB SIDE" to the
Illustration 31 g03172840
Extension harness routed inside spiral wrap (45) 375-4214 Cable As Perform the following procedure to install the 375-4214 Cable As (45) :
Route the 375-4214 Cable As (45) through the existing hole from the machine house.Note: This step may already have been carried out previously at the same time as the boom rotation and angle sensor harnesses were fed through the exit.
Route the extension cable along the existing cable (45) towards the hydraulic hose junction plate on the boom.
Use the spiral wrap to bundle the extension cable along with the existing cables (45). Leave the connector accessible at the hydraulic hose junction plate. 361-3002 Sensor Harness As
Illustration 32 g03172842
(46) Hydraulic hose junction plate on boomPerform the following procedure to install the 361-3002 Sensor Harness As :
At the hydraulic hose junction plate, connect the shorter "PWR/SENSOR/CAN" branch of the 361-3002 Sensor Harness As to the "PWR/SENSOR/CAN" of the 375-4214 Cable As .
Illustration 33 g03172843
(47) Mast angle sensor
Route the "MAST TILT SENSOR" branch of the 361-3002 Sensor Harness As along the existing cable towards the mast angle sensor (47). Refer to Illustration 33.
Connect the "MAST TILT SENSOR" branch to the mast angle sensor.
Use the existing spiral wrap to bundle the 361-3002 Sensor Harness As with the existing cable.
Use cable straps to secure the visible 361-3002 Sensor Harness As to the existing hydraulic hoses.Ensure to leave a light service loop at the sensor. Ensure that there is no tension on the connector. 375-4215 Cable As
Perform the following procedure to install the 375-4215 Cable As :
At the hydraulic hose junction plate, connect the 375-4215 Cable As to the 361-3002 Sensor Harness As . Refer to Illustration 32.
Illustration 34 g03172844
(48) Hose collar (49) Spiral wrap around existing cable routed towards mast
Illustration 35 g02552863
Mast passage hole
Route the extension cable along with the existing cable through the hose collar (48) and up through the mast passage hole. Refer to Illustration 34 and Illustration 35.
Route the extension cable with the existing spiral wrap (49) between the hydraulic hose junction plate and the mast passage hole. Refer to Illustration 35.Note: Be sure to observe safe procedures for access. Maintain a three-point contact and/or use a safety harness.
Route the extension cable up towards the top of the mast. Follow the path of existing cables and route through the protective corridor.Use p-clips and cable straps to secure along the mast.
At the base of the mounting bracket, route the connector through the hollow of the base from non-cab side to cab-side of the mast.
Coil excess 375-4215 Cable As below the base of the support bracket. Use cable straps to secure the excess harness to the existing harnesses. 353-8858 Wiring Harness
Perform the following procedure to install the 353-8858 Wiring Harness :
Ensure that the mast is in a lowered position.
Connect the 353-8858 Wiring Harness between the 291-1913 Satellite Receiver As (GNSS, MS990). Ensure the following connections:
Connect the branch labeled "NON-CAB SIDE" to the slave satellite receiver.
Connect the branch labeled "CAB SIDE" to the
Caterpillar SIS machinery equipment:
Caterpillar SIS
C15 On-highway Engine BXS00001-UP »
223-9259
PLUG GP-WATER LINES
C15 On-Highway Truck MXS00001-UP »
223-9259
PLUG GP-WATER LINES
C15 Engine for Combat and Tactical Vehicles BS900001-UP POWERED BY C15 Engine »
223-9259
PLUG GP-WATER LINES
C15 Euro III Truck Engine RKS00001-UP »
223-9259
PLUG GP-WATER LINES
Cat SIS web machinery list:
Parts plug Caterpillar catalog:
1673C, 211B, 213B, 214B, 216, 216B, 226B, 228, 232B, 235, 236, 236B, 236D, 242B, 242D, 245, 246C, 246D, 247, 247B, 248, 252B, 256C, 257B, 257D, 259D, 262C, 262C2, 262D, 267, 267B, 268B, 272C, 272D, 27...
153, 163, 173B, 183B, 191, 205B, 211B, 213B, 214B, 215, 215B, 215C, 215D, 216B, 216B3, 219D, 225, 225D, 226B, 226B3, 227, 229, 229D, 231D, 232B, 235, 235B, 235C, 235D, 236B, 236B3, 236D, 242B, 242B3, ...
1090, 1190, 1190T, 1290T, 130G, 1390, 140, 1693, 173B, 183B, 205B, 211B, 214B, 215, 215B, 215D, 219D, 225, 225D, 227, 229, 2290, 231D, 235, 235B, 235C, 235D, 236D, 2384C, 2390, 2391, 242D, 245, 245B, ...
1090, 1190, 1190T, 1290T, 1390, 14G, 153, 163, 205B, 211B, 214B, 215, 215B, 215C, 215D, 216, 219D, 225, 225D, 226B, 226B3, 227, 229, 2290, 229D, 231D, 232B, 235, 235B, 235C, 235D, 236, 236B, 2390, 239...
120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 12H, 12H ES, 12H NA, 12K, 12M, 135H, 135H NA, 140, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 141, 143H, 14H, 14H NA, 14M, 153, 160H, 160H ES, 160H N...
10 FT, 10B, 1140, 1145, 1150, 1160, 120B, 120G, 12E, 12G, 130G, 140B, 140G, 14G, 16, 1673, 1673B, 1673C, 1674, 1676, 1693, 16G, 206, 212, 214, 215, 215B, 215C, 224, 225, 225D, 227, 229, 229D, 231D, 23...
1090, 1190, 1190T, 120H, 120H ES, 120H NA, 120M, 120M 2, 1290T, 12H, 12M, 12M 2, 12M 3, 12M 3 AWD, 135H, 135H NA, 1390, 140H, 140K, 140M, 140M 2, 140M 3, 140M 3 AWD, 143H, 14M, 160H, 160K, 160M, 160M ...
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 120M 2, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 12M 3, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 140M 3, 143H, 14G, 14H, 14H NA, 14...
1140, 1145, 1150, 1160, 120, 120G, 140B, 16, 1673C, 1674, 1693, 16G, 16H NA, 24M, 3145, 3150, 3160, 3304, 3306, 3406, 3406B, 3406C, 3406E, 3408, 3408B, 3408C, 3412, 3412C, 3412D, 3456, 350 L, 365C, 36...
10-20B, 120H, 120K, 120K 2, 120M, 120M 2, 12H, 12K, 12M, 12M 2, 135H, 140H, 140K, 140K 2, 140M, 140M 2, 143H, 14H, 14M, 160H, 160K, 160M, 160M 2, 163H, 16H, 16M, 2290, 236D, 2390, 2391, 242D, 246C, 24...
120H, 120K, 120K 2, 120M, 120M 2, 12H, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 135H, 140H, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 143H, 14H, 14M, 160H, 160K, 160M, 160M 2, 160M 3, 160M 3 AWD, 163H...
1140, 1145, 1150, 1160, 120G, 130G, 215, 225, 227, 231D, 3160, 3204, 3208, 3304, 3304B, 3406, 3406B, 3406C, 3406E, 3456, 365C, 365C L, 365C L MH, 374D L, 385B, 385C, 385C FS, 385C L, 385C L MH, 390D, ...
2314329
PLUG GP-ENGINE
789D, C15
789D, C15
2234735
PLUG GP-ENGINE
735, 740, 789D, C15
735, 740, 789D, C15
2296710
PLUG GP-CYLINDER BLOCK
385C, C15, C18
385C, C15, C18
3315710
PLUG GP-ENGINE
C1.5, C2.2
C1.5, C2.2
3072667
PLUG GP-ENGINE
C13, TH35-C13T
C13, TH35-C13T
2495235
PLUG GP-AIR INLET MANIFOLD
C11, C13
C11, C13
2233873
PLUG GP-ENGINE
C11, C13
C11, C13
2799540
PLUG GP-ENGINE
390F L, 735B, 740B, 770G, 770G OEM, 772G, 772G OEM, C-18, C15, C18, CX31-C15I, CX35-P800, D8T, D9T, TH35-C15I
390F L, 735B, 740B, 770G, 770G OEM, 772G, 772G OEM, C-18, C15, C18, CX31-C15I, CX35-P800, D8T, D9T, TH35-C15I