AVSPARE.COM
parts catalog

PLUG 2H9839 - Caterpillar



2H9839 PLUG Caterpillar parts 583H, 619, 657, D353C, D9E PLUG
Rating:
52
Alternative (cross code) number:
CA2H9839
2H-9839
2H9839
Caterpillar 2H9839 PLUG
Weight: 0.88 pounds 0 kg.

Buy PLUG 2H9839 Caterpillar genuine, new aftermarket tractor parts with delivery
CABLE CONTROL, WHEEL SCRAPER,

Compatible equipment models: 2H9839:

CABLE CONTROL  619  
INDUSTRIAL ENGINE  D353C  
PIPELAYER  583H  
TRACK-TYPE TRACTOR  D9E  
WHEEL SCRAPER  657   Caterpillar
Number on catalog scheme: None
 
  For full view, you need register

Information:


Illustration 1 g00928237
This diagnostic code is associated with the Proportional Solenoid (Auger Forward) for the left side. The FMI 05 means that the ECM has determined that the current of the solenoid is below normal. The possible causes of this diagnostic code are listed below:
The energize circuit of the solenoid is open.
The return circuit of the solenoid is open.
The solenoid has failed.
The ECM has failed. ECM failure is unlikely. Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear these diagnostic codes when the original diagnostic code has been corrected. Ensure that the diagnostic code of CID 1735 FMI 05 is active before performing this procedure.Note: Use the 146-4080 Digital Multimeter for the measurements in this procedure.System Response:When this diagnostic code is active, the following response occurs:
The ECM will turn off the current to the failed solenoid.
The left auger cannot run in the forward direction.
The fault lamp for the material system, the tamp system, and the auxiliary system is ON.
The action lamp is ON.Test Step 1. CHECK THE SOLENOID.
Turn the disconnect switch and the key start switch to the ON position. Do not start the engine.
Disconnect the solenoid with the active diagnostic code from the machine harness.
At the machine harness connector for the solenoid, place a jumper wire from contact 1 (wire A912-PU) to contact 2 (wire F760-PU).
Observe the status of the CID 1735 FMI 05.Expected Result:The CID 1735 FMI 05 remains active. The FMI has not changed and the "05" is still active.Results:
YES - The diagnostic code remains active. The jumper wire does not affect the diagnostic code. Proceed to Test Step 2.
NO - The diagnostic is no longer active. The solenoid has failed.Repair: The solenoid has failed. Repeat this Test Step "CHECK THE SOLENOID" in order to verify the solenoid failure. Replace the solenoid. Verify that the new solenoid corrects the problem.STOPTest Step 2. CHECK THE HARNESS FOR AN OPEN.
Turn the key start switch and the disconnect switch to the OFF position.
Disconnect the machine harness connector J2 from the ECM.
The jumper wire that was installed in the previous test remains in place.
At the machine harness connector, measure the resistance from signal contact J2-51 (wire A912-PU) to contact J2-49 (wire F760-PU).Expected Result:The resistance is less than 5 ohms.Results:
OK - The resistance is less than 5 ohms. The machine harness is correct. Proceed to Test Step 3.
NOT OK - The resistance is greater than 5 ohms. The resistance measurement is not correct. There is an open circuit in the machine harness.Repair: The open is in wire A912-PU or in wire F760-PU of the machine harness. Repair the machine harness or replace the machine harness.STOPTest Step 3. CHECK IF THE DIAGNOSTIC CODE REMAINS.
Inspect the contacts of the harness connectors and clean the harness connectors.
Reconnect all harness connectors.
Turn the disconnect switch and the key start switch to the ON position.
Operate the machine.
Check the status of the CID 1735 FMI 05.Expected Result:The CID 1735 FMI 05 is active. Results:
YES - The CID 1735 FMI 05

Caterpillar parts catalog:

Caterpillar parts catalog
D353 ENGINE 46B00001-00598
583 PIPELAYER 38A00001-00078 (MACHINE)
D8H TRACTOR / POWER SHIFT / 46A00001-03043 (MACHINE)
583 PIPELAYER 38A00001-00078 (MACHINE)
D8H TRACTOR / POWER SHIFT / 46A00001-03043 (MACHINE)
D9 TRACTOR 50A00001-00212 (MACHINE)
CABLE CONTROLS FOR 619, 630 & 631 TRACTORS 66F00001-UP
657 SCRAPER 19G00001-00516 (MACHINE)
666 SCRAPER 20G00001-00175 (MACHINE)
657 SCRAPER 19G00001-00516 (MACHINE)


Parts plug Caterpillar catalog:

7H3719 PLUG
D342, D353C, D379, D398
7H3724 PLUG
D342, D353C, D379, D398
3L8852 PLUG
120G, 12G, 130G, 140G, 14G, 824B, 826B, AD40, AD45, AE40, AE40 II, D342, D8H, R1300, R1700 II
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.