AVSPARE.COM
parts catalog

PLUG 5436370 - Caterpillar


5436370 PLUG Caterpillar parts
Rating:
16
Alternative (cross code) number:
CA5436370
543-6370
5436370
Caterpillar 5436370 PLUG
Weight: 0.03 pounds 0 kg.

Buy PLUG 5436370 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:

Introduction
This Special Instruction describes the disassembly procedure and the assembly procedure for the hydraulic cylinder. If you need more information about the procedure, consult your Caterpillar dealer.Disassembly Procedure
Illustration 1 g01429884
(1) Cylinder Body (2) Rod (3) Piston (4) Cylinder Head (5) Check Valve (6) Lock Screw (7) Piston Seal (8) Wear Ring (9) O-Ring Seal (10) O-Ring Seal (11) Back Up Ring (12) O-Ring Seal (13) Rod Seal (14) Rod WiperNote: The following items are included in the service kit: (7), (8), (9), (10), (11), (12), (13) and (14).
Personal injury can result from hydraulic oil pressure and hot oil.Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system.Make sure all of the work tools have been lowered to the ground, and the oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the component should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism.
Remove the cylinder from the coupler.
Clean the cylinder in order to remove any foreign particles.
Clean the work area and the tools that will be used.
Place covers over disassembled parts in order to protect the parts and prevent contamination.
Remove the rod (2) from the cylinder body (1). This is accomplished by unscrewing the cylinder head (4) from the cylinder body.
Pull the cylinder head (4) and the cylinder rod (2) from the cylinder body (1) .
Remove the lock screw (6) that locks the piston (3) in place.Note: This screw is staked in place. The deformed area may need to be filed off before removal.
Remove the piston (3) from the rod (2) .
Remove the piston seal (7), the O-ring seal (9) and the wear ring (8) from the piston (3) .
Pull the cylinder rod (2) out of the cylinder head (4) .
Remove the rod wiper (14), and the rod seal (13) from the cylinder head (4) .
Remove items (10), (11) and (12) from the cylinder head.Assembly Procedure
Note: Clean all parts before assembly.Note: Caterpillar recommends petroleum based oil in order to lubricate parts during the assembly process.
Replace items (10, 11, 12, 13, 14) in the cylinder head (8) .
Replace the piston seal (7), the wear ring (8), and the O-ring (9) in the piston (3) .
Install the cylinder head assembly onto the rod.
Install


Parts plug Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.