6E4502 PLUG Caterpillar parts
120H, 120H ES, 120H NA, 120K, 120K 2, 12H, 12H ES, 12H NA, 12K, 135H, 135H NA, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 14H, 14H NA, 160H, 160H ES, 160H NA, 160K, 163H, 163H NA, 16H, 16H NA, 24H
Rating:
Alternative (cross code) number:
CA6E4502
6E-4502
6E4502
CA6E4502
6E-4502
6E4502
Weight: 0.02 pounds 0 kg.
Information:
DASH SIZE
000000000002
FLANGE DIAMETER
0
mm
HEX SIZE
11.13
mm
OVERALL LENGTH
19.21
mm
SHOULDER LENGTH
13.25
mm
STANDARD SEAL PART NUMBER
4J7533
THREAD SIZE
.31-24
MOTOR GRADER,
Compatible equipment models: 6E4502:
Information:
Clean the cooling system and flush the cooling system before the recommended maintenance interval if the following conditions exist:
The engine overheats frequently.
Foaming is observed.
The oil has entered the cooling system and the coolant is contaminated.
The fuel has entered the cooling system and the coolant is contaminated.
Use of commercially available cooling system cleaners may cause damage to cooling system components. Use only cooling system cleaners that are approved for Caterpillar engines.
Note: Inspect the water pump and the water temperature regulator after the cooling system has been drained. This is a good opportunity to replace the water pump, the water temperature regulator, and the hoses, if necessary. Drain
Pressurized System: Hot coolant can cause serious burns. To open the cooling system filler cap, stop the engine and wait until the cooling system components are cool. Loosen the cooling system pressure cap slowly in order to relieve the pressure.
Stop the engine and allow the engine to cool. Loosen the cooling system filler cap slowly in order to relieve any pressure. Remove the cooling system filler cap. Note: Refer to Operation and Maintenance Manual, "General Hazard Information" for information on Containing Fluid Spillage.
Open the cooling system drain valve (if equipped). If the cooling system is not equipped with a drain valve, remove one of the drain plugs. Allow the coolant to drain into a suitable container.
Properly dispose of the drained material. Obey local regulations for the disposal of the material.
Dispose of used engine coolant properly or recycle. Various methods have been proposed to reclaim used coolant for reuse in engine cooling systems. The full distillation procedure is the only method acceptable by Caterpillar to reclaim the used coolant.
Flush
Flush the cooling system with clean water in order to remove any debris.
Close the drain valve (if equipped). Clean the drain plugs. Install the drain plugs. Refer to Torque Specifications, SENR3130 for more information on the correct torques.
Do not fill the cooling system faster than 5 L (1.3 US gal) per minute to avoid air locks.Cooling system air locks may result in engine damage.
Fill the cooling system with a mixture of clean water and Caterpillar Fast Acting Cooling System Cleaner. Add 0.5 L (1 pint) of cleaner per 15 L (4 US gal) of the cooling system capacity. Install the cooling system filler cap.
Start and run the engine at low idle for a minimum of 30 minutes. The coolant temperature should be at least 82 °C (180 °F).
Improper or incomplete rinsing of the cooling system can result in damage to copper and other metal components.To avoid damage to the cooling system, make sure to completely flush the cooling system with clear water. Continue to flush the system until all signs of the cleaning agent are gone.
Stop the engine and allow the engine to cool. Loosen the cooling system filler cap slowly in order to relieve any pressure. Remove the cooling system filler cap. Open the drain valve (if equipped) or remove the cooling system drain plugs. Allow the water to drain. Flush the cooling system with
The engine overheats frequently.
Foaming is observed.
The oil has entered the cooling system and the coolant is contaminated.
The fuel has entered the cooling system and the coolant is contaminated.
Use of commercially available cooling system cleaners may cause damage to cooling system components. Use only cooling system cleaners that are approved for Caterpillar engines.
Note: Inspect the water pump and the water temperature regulator after the cooling system has been drained. This is a good opportunity to replace the water pump, the water temperature regulator, and the hoses, if necessary. Drain
Pressurized System: Hot coolant can cause serious burns. To open the cooling system filler cap, stop the engine and wait until the cooling system components are cool. Loosen the cooling system pressure cap slowly in order to relieve the pressure.
Stop the engine and allow the engine to cool. Loosen the cooling system filler cap slowly in order to relieve any pressure. Remove the cooling system filler cap. Note: Refer to Operation and Maintenance Manual, "General Hazard Information" for information on Containing Fluid Spillage.
Open the cooling system drain valve (if equipped). If the cooling system is not equipped with a drain valve, remove one of the drain plugs. Allow the coolant to drain into a suitable container.
Properly dispose of the drained material. Obey local regulations for the disposal of the material.
Dispose of used engine coolant properly or recycle. Various methods have been proposed to reclaim used coolant for reuse in engine cooling systems. The full distillation procedure is the only method acceptable by Caterpillar to reclaim the used coolant.
Flush
Flush the cooling system with clean water in order to remove any debris.
Close the drain valve (if equipped). Clean the drain plugs. Install the drain plugs. Refer to Torque Specifications, SENR3130 for more information on the correct torques.
Do not fill the cooling system faster than 5 L (1.3 US gal) per minute to avoid air locks.Cooling system air locks may result in engine damage.
Fill the cooling system with a mixture of clean water and Caterpillar Fast Acting Cooling System Cleaner. Add 0.5 L (1 pint) of cleaner per 15 L (4 US gal) of the cooling system capacity. Install the cooling system filler cap.
Start and run the engine at low idle for a minimum of 30 minutes. The coolant temperature should be at least 82 °C (180 °F).
Improper or incomplete rinsing of the cooling system can result in damage to copper and other metal components.To avoid damage to the cooling system, make sure to completely flush the cooling system with clear water. Continue to flush the system until all signs of the cleaning agent are gone.
Stop the engine and allow the engine to cool. Loosen the cooling system filler cap slowly in order to relieve any pressure. Remove the cooling system filler cap. Open the drain valve (if equipped) or remove the cooling system drain plugs. Allow the water to drain. Flush the cooling system with
Cat SIS web machinery list:
Parts plug Caterpillar catalog:
5P7684
PLUG
225, 24H, 30/30, 330C, 330D L, 330D MH, 3406, 3406B, 3406C, 3406E, 3408E, 3412E, 345B II, 345B II MH, 345C, 345C L, 345C MH, 345D, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L, 349E L HVG, 349E L VG,...
225, 24H, 30/30, 330C, 330D L, 330D MH, 3406, 3406B, 3406C, 3406E, 3408E, 3412E, 345B II, 345B II MH, 345C, 345C L, 345C MH, 345D, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L, 349E L HVG, 349E L VG,...
6B5262
PLUG
117, 118, 119, 120G, 127, 128, 129, 12E, 12G, 130G, 140G, 14G, 14H, 14H NA, 16, 160G, 16G, 16H, 16H NA, 215, 215B, 215C, 225, 227, 229, 229D, 231D, 235, 235B, 235C, 245, 25, 30, 3192, 330 L, 330B, 340...
117, 118, 119, 120G, 127, 128, 129, 12E, 12G, 130G, 140G, 14G, 14H, 14H NA, 16, 160G, 16G, 16H, 16H NA, 215, 215B, 215C, 225, 227, 229, 229D, 231D, 235, 235B, 235C, 245, 25, 30, 3192, 330 L, 330B, 340...
1095839
PLUG-DRAIN
16G, 16H NA, 24H, 24M, 3406E, 3412, 3412C, 365C, 365C L, 365C L MH, 374D L, 374F L, 385B, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 390F L, 5090B, 5110B, 578, 583T, 587R, 587T, 589, 613G, 621E, ...
16G, 16H NA, 24H, 24M, 3406E, 3412, 3412C, 365C, 365C L, 365C L MH, 374D L, 374F L, 385B, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 390F L, 5090B, 5110B, 578, 583T, 587R, 587T, 589, 613G, 621E, ...
3P7009
PLUG-CUP
120G, 12G, 130G, 140G, 14G, 14H, 14H NA, 160G, 16G, 16H, 16H NA, 30/30, 375, 5080, 611, 615, 615C, 814B, 814F, 814F II, 815B, 815F, 815F II, 816F, 816F II, 936, 936F, 950B, 950B/950E, 950F, 966C, 966D...
120G, 12G, 130G, 140G, 14G, 14H, 14H NA, 160G, 16G, 16H, 16H NA, 30/30, 375, 5080, 611, 615, 615C, 814B, 814F, 814F II, 815B, 815F, 815F II, 816F, 816F II, 936, 936F, 950B, 950B/950E, 950F, 966C, 966D...
3S0036
PLUG-CORE
120G, 12G, 130G, 140G, 14E, 14G, 14H, 14H NA, 16, 160G, 16G, 16H, 16H NA, 24H, 3406B, 3406C, 3406E, 3456, 561D, 589, 621, 621B, 621E, 621F, 621G, 621H, 621K, 621R, 623, 623B, 623E, 623F, 623G, 623H, 6...
120G, 12G, 130G, 140G, 14E, 14G, 14H, 14H NA, 16, 160G, 16G, 16H, 16H NA, 24H, 3406B, 3406C, 3406E, 3456, 561D, 589, 621, 621B, 621E, 621F, 621G, 621H, 621K, 621R, 623, 623B, 623E, 623F, 623G, 623H, 6...
9G7132
PLUG-ORIFICE
120H, 120H ES, 120H NA, 120K, 120K 2, 12H, 12H ES, 12H NA, 12K, 135H, 135H NA, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 160H, 160H ES, 160H NA, 160K, 163H, 163H NA, 621E, 621F, 621G, 623E, 623F, 62...
120H, 120H ES, 120H NA, 120K, 120K 2, 12H, 12H ES, 12H NA, 12K, 135H, 135H NA, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 160H, 160H ES, 160H NA, 160K, 163H, 163H NA, 621E, 621F, 621G, 623E, 623F, 62...
8M3837
PLUG
120H, 120H ES, 120H NA, 120K, 120K 2, 12H, 12H ES, 12H NA, 12K, 135H, 135H NA, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 14H, 14H NA, 160H, 160H ES, 160H NA, 160K, 163H, 163H NA, 16H, 16H NA, 215, 2...
120H, 120H ES, 120H NA, 120K, 120K 2, 12H, 12H ES, 12H NA, 12K, 135H, 135H NA, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 14H, 14H NA, 160H, 160H ES, 160H NA, 160K, 163H, 163H NA, 16H, 16H NA, 215, 2...
2286089
PLUG
1090, 1190, 1190T, 120K, 120K 2, 120M, 120M 2, 1290T, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 14M, 160K, 160M, 160M 2, 160M 3, 160M 3 AWD, 16M, 2290, 2390, 2...
1090, 1190, 1190T, 120K, 120K 2, 120M, 120M 2, 1290T, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 14M, 160K, 160M, 160M 2, 160M 3, 160M 3 AWD, 16M, 2290, 2390, 2...
1335631
PLUG
120H, 12H, 135H, 140H, 143H, 160H, 163H, 527, 572R, 572R II, 797, 797B, 797F, D10N, D10R, D11N, D11R, D6H, D6H XL, D6H XR, D6R, D6R II, D6R III, D6R STD, D6T, D6T LGP, D6T LGPPAT, D6T XL, D7E, D7E LGP...
120H, 12H, 135H, 140H, 143H, 160H, 163H, 527, 572R, 572R II, 797, 797B, 797F, D10N, D10R, D11N, D11R, D6H, D6H XL, D6H XR, D6R, D6R II, D6R III, D6R STD, D6T, D6T LGP, D6T LGPPAT, D6T XL, D7E, D7E LGP...
2385508
PLUG AS-ORIFICE
24H, 517, 527, 561M, 578, 583R, 587R, 589, 844, 844H, 844K, 854G, 854K, 988F, 988F II, 990, 990 II, 990H, 990K, 992C, 992D, 992G, 992K, 993K, 994, 994D, 994F, 994H, D10R, D11R, D11T, D4H XL, D4HTSK II...
24H, 517, 527, 561M, 578, 583R, 587R, 589, 844, 844H, 844K, 854G, 854K, 988F, 988F II, 990, 990 II, 990H, 990K, 992C, 992D, 992G, 992K, 993K, 994, 994D, 994F, 994H, D10R, D11R, D11T, D4H XL, D4HTSK II...
4T2069
PLUG
120G, 12G, 130G, 140G, 14G, 14H, 14H NA, 160G, 16G, 16H, 16H NA, 517, 572R, 572R II, 578, 583R, 583T, 587R, 587T, 589, 910, 931B, 931C II, 933, 939, 943, 953, 963, 963B, 973, D10, D10N, D10R, D10T, D1...
120G, 12G, 130G, 140G, 14G, 14H, 14H NA, 160G, 16G, 16H, 16H NA, 517, 572R, 572R II, 578, 583R, 583T, 587R, 587T, 589, 910, 931B, 931C II, 933, 939, 943, 953, 963, 963B, 973, D10, D10N, D10R, D10T, D1...
6N9590
PLUG-DRAIN
24H, 5110B, 5130, 5130B, 5230, 5230B, 631E, 631G, 633E II, 637D, 637E, 637G, 651E, 657E, 69D, 769C, 769D, 771C, 771D, 772B, 773B, 773D, 773E, 775B, 775D, 775E, 776C, 776D, 777, 777B, 777D, 784B, 784C,...
24H, 5110B, 5130, 5130B, 5230, 5230B, 631E, 631G, 633E II, 637D, 637E, 637G, 651E, 657E, 69D, 769C, 769D, 771C, 771D, 772B, 773B, 773D, 773E, 775B, 775D, 775E, 776C, 776D, 777, 777B, 777D, 784B, 784C,...
6Y3852
PLUG
120H, 120H ES, 120H NA, 120K, 120K 2, 12H, 12H ES, 12H NA, 12K, 135H, 135H NA, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 160H, 160H ES, 160H NA, 160K, 163H, 163H NA
120H, 120H ES, 120H NA, 120K, 120K 2, 12H, 12H ES, 12H NA, 12K, 135H, 135H NA, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 160H, 160H ES, 160H NA, 160K, 163H, 163H NA
3092995
PLUG AS
120H, 120H NA, 120K, 120K 2, 12H, 12H NA, 12K, 135H, 135H NA, 140H, 140H NA, 140K, 140K 2, 143H, 160H, 160H NA, 160K, 163H, 163H NA
120H, 120H NA, 120K, 120K 2, 12H, 12H NA, 12K, 135H, 135H NA, 140H, 140H NA, 140K, 140K 2, 143H, 160H, 160H NA, 160K, 163H, 163H NA
4E0645
PLUG AS
120H, 12H, 12H NA, 135H, 140H, 140H NA, 143H, 160H, 160H NA, 163H NA
120H, 12H, 12H NA, 135H, 140H, 140H NA, 143H, 160H, 160H NA, 163H NA
1163508
PLUG
330, 330 L, 345B, 345B II, 345B L, 345C, 345C L, 350, 350 L, 365B, 365B II, 365B L, 365C, 365C L, 365C L MH, 374D L, 374F L, OEMS
330, 330 L, 345B, 345B II, 345B L, 345C, 345C L, 350, 350 L, 365B, 365B II, 365B L, 365C, 365C L, 365C L MH, 374D L, 374F L, OEMS
6I6989
PLUG
330, 330 FM L, 330 L, 350, OEMS
330, 330 FM L, 330 L, 350, OEMS
8J5576
PLUG
120G, 130G, 140G, 14G, 160G, 16G
120G, 130G, 140G, 14G, 160G, 16G
1291047
PLUG
140H ES, 143H, 14H NA, 160H ES, 163H NA, 16H NA
140H ES, 143H, 14H NA, 160H ES, 163H NA, 16H NA
1118262
PLUG AS
143H, 163H NA
143H, 163H NA
1279169
PLUG
143H, 163H, 163H NA
143H, 163H, 163H NA
0837733
PLUG
143H, 163H, 163H NA
143H, 163H, 163H NA
8X8055
PLUG
120H, 120H ES, 120H NA, 120K, 120K 2, 12H, 12H ES, 12H NA, 12K, 135H, 135H NA, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 14H, 14H NA, 160H, 160H ES, 160H NA, 160K, 163H, 163H NA, 16H, 16H NA, 24H
120H, 120H ES, 120H NA, 120K, 120K 2, 12H, 12H ES, 12H NA, 12K, 135H, 135H NA, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 14H, 14H NA, 160H, 160H ES, 160H NA, 160K, 163H, 163H NA, 16H, 16H NA, 24H
1010029
PLUG
120H NA, 135H NA, 140H ES, 140H NA, 143H, 14H NA, 160H ES, 160H NA, 163H NA
120H NA, 135H NA, 140H ES, 140H NA, 143H, 14H NA, 160H ES, 160H NA, 163H NA