PLUG AS-CONNECTOR 8N1529 - Caterpillar

General Information
The EMCP discrete I/O module can be installed on a generator set package or in a remote location away from the generator set. The purpose of the discrete input/output (I/O) module is to provide auxiliary switch inputs or relay contact outputs. Up to four DIO modules can be used on the EMCP 4.2 accessory CAN data link. The DIO modules must be configured to unique "Electronic Control Unit" (ECU) instance numbers.
Illustration 1 g02279474
EMCP discrete I/O module
Discrete I/O Module Features
The following list provides information about the features of the discrete I/O module:
Reads 12 discrete inputs
Sets eight "Form C" relay outputs
Converts between physical I/O and CAN data link commands
All channels are scanned in 100 ms
0V to 0.8V low-level input voltage range
3.75V to 24V high-level input voltage range
Inputs have internal pull-up resistors
LED to indicate communication network status
Ambient storage temperature range is −50° C (−58° F) to 120° C (248° F)
Protected against 95% humidity non-condensing, 30° C (86° F) to 60° C (140° F)
Retains all configured values in nonvolatile memory so that no information is lost when the module is de-energized
Configured on the accessory CAN data link using the Cat ET
Operates on the EMCP 4 Accessory CAN data links
Node address is automatically configuredSpecifications
Table 1 lists the specifications for the Input/Output Module.
Table 1
Input/Output Module Specifications
Operating voltage range 5 VDC to 32 VDC
Nominal voltage 12 VDC or 24 VDC
Over voltage capability 32 VDC for 1 hour at 85° C (185° F)
Ambient operating temperature −40° C (−40° F) to 70° C (158° F)
Resistive loads Rated for 3A at 30 VDC
Output relay contact ratings 2A @125 VAC/2A@30 VDC
Maximum current draw 400mA plus 50mA per energized relay at 12 VDC Note: Power supply inputs are protected against transient surges and short circuits. Power supply inputs are isolated from I/O modules.Discrete I/O Wiring
Illustration 2 shows typical connector wiring for the I/O.
Illustration 2 g02277674Illustration 3 shows typical electrical schematic wiring for the I/O.
Illustration 3 g02277898Table 2 lists the names for each input connection and the corresponding pin.
Table 2
Inputs Pin
DIN1 1
DIN2 11
DIN3 21
DIN4 31
DIN5 2
DIN6 12
DIN7 22
DIN8 32
DIN9 3
DIN10 13
DIN11 23
DIN12 33
GND 4
GND 14
GND 24
GND 34 Note: The "GND" pin is not the package ground, but the "Isolated Reference" for the module.The following definitions apply to Table 3 abbreviations:
NO = Normally open
NC = Normally closed
C = CommonTable 3 lists the names for each input connection and the corresponding pin.
Table 3
Outputs Pin
NC_1 5
C_1 6
NO_1 7
NC_2 15
C_2 16
NO_2 17
NC_3 25
C_3 26
NO_3 27
NC_4 35
C_4 36
NO_4 37
NC_5 8
C_5 9
NO_5 10
NC_6 18
C_6 19
NO_6 20
NC_7 28
C_8 29
NO_7 30
NC_8 38
C_8 39
NO_8 40 Discrete I/O Software Configuration
DIO modules can be programmed the use of the Cat Service Tool. Cat Service Tool can also be used to flash program DIO modules in order to update software. The service tool software must be installed on a Windows based personal computer. The Cat communication adapter must be connected between the PC and the CAN data link on which the target DIO module is connected.Note: The service tool may be connected to the EMCP 4 accessory data link service connector.Use the following steps