5A6095 PLUNGER ASSEM. (Japanese) Caterpillar parts
950
Rating:
Alternative (cross code) number:
CA5A6095
5A-6095
5A6095
CA5A6095
5A-6095
5A6095
Weight: 1 pounds 0 kg.
WHEEL LOADER,
Compatible equipment models: 5A6095:
Number on catalog scheme:
None
For full view, you need register
Information:
Removal Procedure
Start By:
Remove the crankshaft rear seal. Refer to Disassembly and Assembly Manual, "Crankshaft Rear Seal - Remove" for the correct procedure.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Wear sleeves are used to reclaim worn seal surfaces or damaged seal surfaces. Wear sleeves are not original equipment.
Illustration 1 g03358286
Use a sharp tool to score a deep line across the crankshaft wear sleeve (1). Note: Take care to avoid damaging the crankshaft.
Insert a thin blade between crankshaft wear sleeve (1) and crankshaft (2) below the scored line. The crankshaft wear sleeve will separate along the line.
Remove crankshaft wear sleeve (1) from crankshaft (2). Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description
A 1U-8846 Liquid Gasket
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Ensure that the crankshaft is thoroughly clean and dry.
Illustration 2 g03358287
Apply a small continuous bead of Tooling (A) to the inner surface of a new crankshaft wear sleeve (1) at Position X. Apply the bead of Tooling (A) 5 mm (0.2 inch) from the flange end of crankshaft wear sleeve.
Illustration 3 g03338321
Align crankshaft wear sleeve (1) with crankshaft (2). Position installation tool (3) that is provided with the crankshaft wear sleeve over the crankshaft. Use a hammer to drive the crankshaft wear sleeve onto the crankshaft. Ensure that the flange of the crankshaft wear sleeve is 0.40 to 0.60 mm (0.017 to 0.024 inch) from the cylinder block. Note: Measure Distance (Y) between the flange of crankshaft wear sleeve (1) and the cylinder block in two places that are 180 degrees from each other.
Remove installation tool (3).
Ensure that the crankshaft wear sleeve has no rough edges. End By:
Install a new crankshaft rear seal. Refer to Disassembly and Assembly Manual, "Crankshaft Rear Seal - Install" for the correct procedure.
Start By:
Remove the crankshaft rear seal. Refer to Disassembly and Assembly Manual, "Crankshaft Rear Seal - Remove" for the correct procedure.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Wear sleeves are used to reclaim worn seal surfaces or damaged seal surfaces. Wear sleeves are not original equipment.
Illustration 1 g03358286
Use a sharp tool to score a deep line across the crankshaft wear sleeve (1). Note: Take care to avoid damaging the crankshaft.
Insert a thin blade between crankshaft wear sleeve (1) and crankshaft (2) below the scored line. The crankshaft wear sleeve will separate along the line.
Remove crankshaft wear sleeve (1) from crankshaft (2). Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description
A 1U-8846 Liquid Gasket
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Ensure that the crankshaft is thoroughly clean and dry.
Illustration 2 g03358287
Apply a small continuous bead of Tooling (A) to the inner surface of a new crankshaft wear sleeve (1) at Position X. Apply the bead of Tooling (A) 5 mm (0.2 inch) from the flange end of crankshaft wear sleeve.
Illustration 3 g03338321
Align crankshaft wear sleeve (1) with crankshaft (2). Position installation tool (3) that is provided with the crankshaft wear sleeve over the crankshaft. Use a hammer to drive the crankshaft wear sleeve onto the crankshaft. Ensure that the flange of the crankshaft wear sleeve is 0.40 to 0.60 mm (0.017 to 0.024 inch) from the cylinder block. Note: Measure Distance (Y) between the flange of crankshaft wear sleeve (1) and the cylinder block in two places that are 180 degrees from each other.
Remove installation tool (3).
Ensure that the crankshaft wear sleeve has no rough edges. End By:
Install a new crankshaft rear seal. Refer to Disassembly and Assembly Manual, "Crankshaft Rear Seal - Install" for the correct procedure.
Caterpillar parts catalog:
Parts plunger Caterpillar catalog:
1090, 1140, 1150, 1190, 1190T, 1290T, 130G, 140G, 1673C, 1676, 16G, 215, 225, 235, 235D, 245, 24H, 3176C, 3196, 3204, 3208, 330 L, 3304, 3306, 3306B, 3406, 3406B, 3406C, 3406E, 3408, 3408B, 3408C, 340...
120G, 12G, 130G, 140G, 14E, 14G, 14H, 14H NA, 16, 1693, 16G, 16H, 16H NA, 518, 518C, 572G, 583K, 594, 594H, 613, 613B, 621, 621B, 621E, 621F, 621G, 623B, 623E, 623F, 623G, 627, 627B, 627E, 627F, 627G,...
120, 12E, 16, 1673, 1673B, 1673C, 1674, 1676, 1693, 16G, 215, 245, 3304, 3306, 3406, 3408, 3408B, 3408C, 3412, 3412C, 3412D, 561B, 589, 621, 621B, 621R, 623, 627, 631C, 631E, 637D, 637E, 641B, 650B, 6...
16, 1693, 245, 3408, 3412, 3512, 518, 621, 621R, 631C, 637D, 641B, 651E, 657, 657B, 657E, 666, 769, 772, 777, 824, 824B, 834, 941, 950, 951B, 980C, 983, 988, 988B, 992, 992C, D10, D343, D346, D348, D3...
1673, 1673B, 3304, 3306, 621R, 941, 950, 955H, 966C, D330A, D330B, D333A, D4D, D5, D6C, D7F, D7G
1673, 1673B, 1673C, 1674, 1676, 1693, 3304, 3306, 518, 528, 666, 814, 950, 966C, 980B, D334, D342C, D399, D4D, D8H
12G, 130G, 1673C, 225, 235, 3160, 3208, 3304, 3306, 518, 627B, 637D, 639D, 941, 950, 977K, 980B, D4D, D5, D6C, D6D
120H, 120H ES, 120H NA, 120K, 120K 2, 12H, 12H ES, 12H NA, 12K, 135H, 135H NA, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 14H, 14H NA, 160H, 160H ES, 160H NA, 160K, 163H, 163H NA, 16H, 16H NA, 621E, ...
5K6718
PLUNGER
518, 528, 950
518, 528, 950
3Y9750
PLUNGER KIT
966D, 966F
966D, 966F
5S5700
PLUNGER
824B, 825B, 826B
824B, 825B, 826B
5J8331
PLUNGER
988
988
5K6718
PLUNGER
518, 528, 950
518, 528, 950
9M1945
PLUNGER
824, 988
824, 988
7V9179
PLUNGER AS
966C
966C
3Y9130
PLUNGER ASSEM. (For Japan )
980C, 980F
980C, 980F
3Y8246
PLUNGER ASSEM. (For Japan)
966D, 966F, 970F
966D, 966F, 970F