PLUNGER 9W3306 - Caterpillar

9W3306 PLUNGER Caterpillar parts D5B, D5E

Price: query
Add in request price Go to cart

Rating:

Alternative (cross code) number:
CA9W3306
9W-3306
9W3306

Weight: 0.30 pounds 0 kg.

Buy PLUNGER 9W3306 Caterpillar genuine, new aftermarket tractor parts with delivery
TRACK-TYPE TRACTOR,

Compatible equipment models: 9W3306:

TRACK-TYPE TRACTOR D5B D5E Caterpillar

Number on catalog scheme: 51

For full view, you need register

Information:

Illustration 1 g01362188
Connections for the 10 volt sensor supplyThe sensor supply is a power supply that is internal to the ECM. The sensor supply provides 10 VDC in order to operate the sensors.This diagnostic code will be recorded when the Transmission ECM reads the voltage for the circuit of the sensor supply as being below normal.The possible causes of the diagnostic code are listed:
10 VDC is shorted to ground between the sensor and the ECM.
The ECM has failed. This is unlikely.System Response:The results of this diagnostic code are listed:
All of the associated sensors will also log diagnostic codes.Test Step 1. CHECK THE SHIFT LEVER.
Disconnect the machine harness from the shift lever.
Check the status of the diagnostic code.Expected Result:The diagnostic code is no longer active.Results:
OK - The diagnostic code is no longer active. The shift lever has failed.Repair: Replace the shift lever.STOP
NOT OK - The diagnostic code remains active. The shift lever is not causing the diagnostic code. Proceed to Test Step 2.Test Step 2. CHECK FOR A SHORT TO GROUND.
The shift lever remains disconnected from the machine harness.
Turn the disconnect switch and the key start switch to the OFF position.
Disconnect the machine harness from the ECM.
At the ECM, measure the resistance between the contact of the sensor supply voltage (J1-13) and frame ground.Expected Result:The resistance is greater than 5000 ohms. Results:
OK - The resistance that is measured is greater than 5000 ohms. The harness circuit is correct. The ECM has failed.Repair: It is unlikely that the ECM has failed. Exit this procedure. Perform the procedure again. Prior to replacing an ECM, always contact your dealership for possible consultation with Caterpillar. This consultation may greatly reduce repair time. If the ECM requires replacing, refer to Testing and Adjusting, "Electronic Control Module (ECM) - Replace".STOP
NOT OK - The resistance that is measured is less than 5000 ohms. The machine harness has failed. There is a short between frame ground and the contact for the sensor supply voltage in the machine harness.Repair: Repair the machine harness or replace the machine harness.STOP

Caterpillar parts catalog:

Caterpillar parts catalog
Product:

D5E Track-Type Tractor 9RG00001-UP (MACHINE) POWERED BY 3306 Engine

6Y-3180: CONTROL GP-GEARSHIFT » SEBP19960250

Parts plunger Caterpillar catalog:

1P1367 PLUNGER
120B, 120G, 12G, 12H, 12H ES, 12H NA, 130G, 140, 140B, 140G, 140H, 140H ES, 140H NA, 143H, 14G, 14H NA, 160G, 160H, 160H ES, 160H NA, 163H NA, 1673C, 1674, 1693, 16G, 215, 235B, 235C, 235D, 3176, 3176...

1W6541 PLUNGER AS
120G, 12G, 130G, 140G, 143H, 14G, 160G, 160H, 215, 225, 3204, 3304, 3304B, 3306, 3306B, 515, 518C, 525, 527, 572G, 615C, 627B, 627E, 627F, 637E, 815B, 936F, 963, 966F, 966F II, 972G, 973, D250B, D300B...

7T3270 PLUNGER AS
120G, 120H, 120H ES, 120H NA, 120M, 12G, 12H, 12H ES, 12H NA, 12M, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 143H, 14G, 14H, 14H NA, 160G, 160H, 160H ES, 160H NA, 163H NA, 1673C, 16G, 16H, 16...

1S2121 PLUNGER
120G, 12G, 130G, 140G, 14E, 14G, 14H, 14H NA, 16, 1693, 16G, 16H, 16H NA, 518, 518C, 572G, 583K, 594, 594H, 613, 613B, 621, 621B, 621E, 621F, 621G, 623B, 623E, 623F, 623G, 627, 627B, 627E, 627F, 627G,...