3750 POP RIVET Caterpillar parts
PR-105, PR-275, PR-450
Rating:
Alternative (cross code) number:
CA3750
-3750
3750
CA3750
-3750
3750
COLD PLANER,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$64.95
06 Mar 2019
Altezza: Altezza
ATV Parts Connection OJ532/OJ532 2006-2007 Polaris Outlaw 500 2007-2011 Outlaw 525 2x4 Pair of Rear Axle Outer CV Joint Kits
Please verify year, make & model in the description to confirm this will fit your vehicle || 1 year warranty (Excluding lifted vehicles & torn boots) || Stub Height: 3.750 inches (both) - Number of CV housing splines: 23 (both) - Inner race spline count: 20 (both) - Housing diameter: 2.920 inches (both) || Replacement for Polaris OEM #: 1332429
Please verify year, make & model in the description to confirm this will fit your vehicle || 1 year warranty (Excluding lifted vehicles & torn boots) || Stub Height: 3.750 inches (both) - Number of CV housing splines: 23 (both) - Inner race spline count: 20 (both) - Housing diameter: 2.920 inches (both) || Replacement for Polaris OEM #: 1332429
01 Dec 2018
RedLine Tools: RedLine Tools
RedLine Tools RE16814 - Double End Ball Carbide End Mill, 7/32(.2188) Dia, 3.5000" OAL, 3/8(.3750) Shank Dia.5625 Flute Len, 2 Flt, Uncoated
$17.48
28 Apr 2021
US: RedLine Tools
RedLine Tools - 3/8 (.3750) Single End Square Carbide End Mill, Uncoated (Bright) Coating, 4 Flute 1.0000 LOC, Round Shank, 30° Helix Angle, 2.5000 OAL - RE10924
RedLine Tools Uncoated (Bright) || American Made Carbide || 4 Flutes || 30° Helix || Photos may not be the exact representation of products.
RedLine Tools Uncoated (Bright) || American Made Carbide || 4 Flutes || 30° Helix || Photos may not be the exact representation of products.
Number on catalog scheme:
37
For full view, you need register
Information:
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 5S-1330 Valve Spring Compressor 1 Start By:
Remove the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Remove".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01061432
Personal injury can result from being struck by parts propelled by a released spring force.Make sure to wear all necessary protective equipment.Follow the recommended procedure and use all recommended tooling to release the spring force.
Place the cylinder head assembly in an upright position.
Use Tooling (A) in order to compress valve springs (3) and (4). Remove retainer locks (1) .
Remove Tooling (A). Remove rotocoil assemblies (2), valve springs (3) and (4), and bases (5) .
Remove inlet valves (6) and exhaust valves (7) from the cylinder head.Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 5S-1330 Valve Spring Compressor 1
Illustration 2 g01061432
Improper assembly of parts that are spring loaded can cause bodily injury.To prevent possible injury, follow the established assembly procedure and wear protective equipment.
Lubricate inlet valves (6) and exhaust valves (7) with clean engine oil. Install the inlet valves and exhaust valves in the cylinder head assembly.Note: A small amount of grease can be used to hold the retainer locks in position during installation.
Place the following items on inlet valves (6) and exhaust valves (7) : bases (5), valve springs (3) and (4) and rotocoil assemblies (2) .
Use Tooling (A) in order to compress valve springs (3) and (4). Install retainer locks (1) .End By: Install the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Install".
Table 1
Required Tools
Tool Part Number Part Description Qty
A 5S-1330 Valve Spring Compressor 1 Start By:
Remove the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Remove".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01061432
Personal injury can result from being struck by parts propelled by a released spring force.Make sure to wear all necessary protective equipment.Follow the recommended procedure and use all recommended tooling to release the spring force.
Place the cylinder head assembly in an upright position.
Use Tooling (A) in order to compress valve springs (3) and (4). Remove retainer locks (1) .
Remove Tooling (A). Remove rotocoil assemblies (2), valve springs (3) and (4), and bases (5) .
Remove inlet valves (6) and exhaust valves (7) from the cylinder head.Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 5S-1330 Valve Spring Compressor 1
Illustration 2 g01061432
Improper assembly of parts that are spring loaded can cause bodily injury.To prevent possible injury, follow the established assembly procedure and wear protective equipment.
Lubricate inlet valves (6) and exhaust valves (7) with clean engine oil. Install the inlet valves and exhaust valves in the cylinder head assembly.Note: A small amount of grease can be used to hold the retainer locks in position during installation.
Place the following items on inlet valves (6) and exhaust valves (7) : bases (5), valve springs (3) and (4) and rotocoil assemblies (2) .
Use Tooling (A) in order to compress valve springs (3) and (4). Install retainer locks (1) .End By: Install the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Install".
Caterpillar parts catalog:
Parts pop Caterpillar catalog:
179737018
POP RIVETS
PR-275
PR-275
1050429
POP RIVET
Caterpillar
Caterpillar
0818743
POP RIVETS
Caterpillar
Caterpillar
0785285
POP RIVET
Caterpillar
Caterpillar
0782190
POP-OFF VALV
Caterpillar
Caterpillar
179737018
POP RIVETS
PR-275
PR-275