4Y4057 POST ASSEM. (FRONT) Caterpillar parts
D5H
Rating:
Alternative (cross code) number:
CA4Y4057
4Y-4057
4Y4057
CA4Y4057
4Y-4057
4Y4057
TRACK-TYPE TRACTOR,
Compatible equipment models: 4Y4057:
Number on catalog scheme:
12
For full view, you need register
Information:
Caterpillar ® Electronic Key
Illustration 1 g00793955
The Caterpillar Electronic Key
The electronic key has the same key cut as the universal Caterpillar ® key. The electronic key has an electronic chip that is embedded inside the head of the key. The electronic keys are gray or yellow.Exciter Coil
The exciter coil provides communication between the electronic key and the key reader module.The exciter coil is mounted around the keyswitch. This position allows the exciter coil to communicate with the electronic key. Any ferrous metal between the coil and the electronic key will interfere with the communications. Mounting the coil in the same plane as the top of the key start switch will minimize the interference.Note: Ensure that you have only one electronic key near the exciter coil when the MSS reads the key. If there is more than one key, the ECM will not be able to read the key and the machine will not start.The exciter coil is connected to the harness via a 2-pin connector and a length of wire.Antitheft Keypad
The antitheft keypad, (if equipped), provides the same function as the RFID Key reader. If a valid passcode is not entered, the MSS software will not disarm the machine.Refer to the machine's Operation and Maintenance Manual for details on the Anti-Theft Keypad operation.Electronic Key Reader (MSS3i)
Illustration 2 g01007352When the key start switch is placed in the ON position, the ECM will send a signal over the CAN data link. That signal will command the key reader to excite the coil. The key ID from an electronic key is sent back to the requesting ECM over the CAN data link.Note: The key reader is NOT designed to communicate with the Caterpillar ® Electronic Technician (Cat ® ET). However the key reader control can be flashed via Cat ® ET. Refer to Troubleshooting, "ECM-Flash" for the machine being serviced.Note: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
This device may not cause harmful interference.
This device must accept any interference received, including interference that may cause undesired operation.Status Indicator
Illustration 3 g00862013The state of the MSS is displayed by the status indicator. The green LED of the status indicator turns ON when the system is disarmed. The machine should start. The red LED of the status indicator turns ON when the system is armed and an invalid electronic key has been read by the MSS. The machine should not start. The green LED and the red LED will remain OFF when the machine security system is not installed.Note: The status indicator may be located in the dash cluster on some machines. Refer to the Operation and Maintenance Manual for more information on the dash cluster.
Illustration 1 g00793955
The Caterpillar Electronic Key
The electronic key has the same key cut as the universal Caterpillar ® key. The electronic key has an electronic chip that is embedded inside the head of the key. The electronic keys are gray or yellow.Exciter Coil
The exciter coil provides communication between the electronic key and the key reader module.The exciter coil is mounted around the keyswitch. This position allows the exciter coil to communicate with the electronic key. Any ferrous metal between the coil and the electronic key will interfere with the communications. Mounting the coil in the same plane as the top of the key start switch will minimize the interference.Note: Ensure that you have only one electronic key near the exciter coil when the MSS reads the key. If there is more than one key, the ECM will not be able to read the key and the machine will not start.The exciter coil is connected to the harness via a 2-pin connector and a length of wire.Antitheft Keypad
The antitheft keypad, (if equipped), provides the same function as the RFID Key reader. If a valid passcode is not entered, the MSS software will not disarm the machine.Refer to the machine's Operation and Maintenance Manual for details on the Anti-Theft Keypad operation.Electronic Key Reader (MSS3i)
Illustration 2 g01007352When the key start switch is placed in the ON position, the ECM will send a signal over the CAN data link. That signal will command the key reader to excite the coil. The key ID from an electronic key is sent back to the requesting ECM over the CAN data link.Note: The key reader is NOT designed to communicate with the Caterpillar ® Electronic Technician (Cat ® ET). However the key reader control can be flashed via Cat ® ET. Refer to Troubleshooting, "ECM-Flash" for the machine being serviced.Note: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
This device may not cause harmful interference.
This device must accept any interference received, including interference that may cause undesired operation.Status Indicator
Illustration 3 g00862013The state of the MSS is displayed by the status indicator. The green LED of the status indicator turns ON when the system is disarmed. The machine should start. The red LED of the status indicator turns ON when the system is armed and an invalid electronic key has been read by the MSS. The machine should not start. The green LED and the red LED will remain OFF when the machine security system is not installed.Note: The status indicator may be located in the dash cluster on some machines. Refer to the Operation and Maintenance Manual for more information on the dash cluster.
Caterpillar parts catalog:
Parts post Caterpillar catalog:
8Y7872
POST AS-RH
928F, IT28F
928F, IT28F
8Y8326
POST AS-LH
928F, IT28F
928F, IT28F
621E, 623E, 627E, 631E, 633E II, 637E
6G6759
POST
621B, 621E, 623B, 623E, 627B, 627E
621B, 621E, 623B, 623E, 627B, 627E
651E, 657E
1100235
POST-CENTER
621E, 623E, 627E, 631E, 633E II, 637E, 651E, 657E
621E, 623E, 627E, 631E, 633E II, 637E, 651E, 657E