POWER SYSTEM AR 3076346 - Caterpillar

3076346 POWER SYSTEM AR Caterpillar parts TH35-E81

Price: query
Add in request price Go to cart

Rating:

Alternative (cross code) number:
CA3076346
307-6346
3076346

Buy POWER SYSTEM AR 3076346 Caterpillar genuine, new aftermarket tractor parts with delivery
PETROLEUM TRANSMISSION,

You can buy:

Wear Sleeve 3076346 for Cummins Engine QSK38 QSK50 QSK60 GTA38 K19 K38 K50 N14 V903 G50 G855 GTA855

US$23.99

29 May 2025

FridayParts

Wear Sleeve 3076346 for Cummins Engine QSK38 QSK50 QSK60 GTA38 K19 K38 K50 N14 V903 G50 G855 GTA855

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below

CARTEX Wear Sleeve 3076346 for FITS Cummins Engine QSK38 QSK50 QSK60 GTA38 K19 K38 K50 N14 V903 G50 G855 GTA855

$59.99

09 Oct 2025

CA: High Quality Pa

CARTEX Wear Sleeve 3076346 for FITS Cummins Engine QSK38 QSK50 QSK60 GTA38 K19 K38 K50 N14 V903 G50 G855 GTA855
CARTEX Whether you're a professional mechanic or a DIY enthusiast,We've got you covered with a wide range of parts that meet the highest standards of quality and performance. || Order your High Quality Part with peace of mind, knowing we prioritize your satisfaction. Quality Parts, Superior Performance - it's not just a promise, it's our standard || QUESTIONS? : We at CARTEX - High Quality Parts USA has more than 40 years of experience in industry and has in-house technicians, If you are not sure if this part fits your machine or tractor, just send us an email before you make the purchase and our in house technicians will revert back to you, right away.

$36.67

25 May 2021

US: Transport Diese

Genuine Cummins 3076346 SLEEVE,WEAR
Cummins

For full view, you need register

Compatible equipment models: 3076346:

PETROLEUM TRANSMISSION TH35-E81 Caterpillar

Information:

Unexpected machine movement can cause injury or death.To avoid possible machine movement, move the hydraulic lockout control to the locked position and attach a Special Instruction, SEHS7332, "Do Not Operate" or similar warning tag to the hydraulic lockout control.
Improperly adjusted bucket clearance could cause galling on the contact surfaces of the bucket and stick, resulting in excessive noise and/or damaged O-ring seals.
Illustration 1 g00101687
(1) No gap. (2) Stick boss. (3) Bucket clearance. (4) Shims. (5) Pin. (6) Plate. (7) Bolts. (8) Washers. (9) Location. (10) Flange. (11) Bucket boss.
The clearance of the bucket control linkage on this machine can be adjusted by shimming. If the gap between the bucket and the stick becomes excessive, adjust bucket clearance (3) to 0.5 to 1 mm (0.02 to 0.04 inch).Two shims of different thickness are used at location (9). The thicknesses of the shims are 0.5 mm (0.02 inch) and 1.0 mm (0.04 inch).
Illustration 2 g02109636
Area for linkage adjustment
Position the machine on a level surface and lower the bucket to the ground.
Slowly operate the swing control lever until stick boss (2) and the bucket boss (11) are in full face contact at no gap (1). This will help to determine the total clearance of the connection point of the stick and of the bucket.
Move the hydraulic lockout control to the LOCKED position. Stop the engine.
Measure bucket clearance (3), which is the existing total clearance.
Determine the number of shims that need to be removed from shims (4) by using the following calculation: Subtract 0.5 mm (0.02 inch) or 1.0 mm (0.04 inch) from bucket clearance (3).
Remove the appropriate number of shims at location (9) in order to meet the above thickness. Make sure that you use a minimum of three 0.5 mm (0.02 inch) shims. To remove the shims, remove bolts (7), washers (8), and plate (6).
After the correct number of shims has been removed and pin (5) is aligned with the pin hole, install plate (6), washers (8), and bolts (7). Tighten bolts (7) to a torque of 240 40 N m (175 30 lb ft).
After installation, make sure that bucket clearance (3) is still correct.