3S1660 POWER TAKE-OFF GROUP-REAR Caterpillar parts
D8H, D8K
Rating:
Alternative (cross code) number:
CA3S1660
3S-1660
3S1660
CA3S1660
3S-1660
3S1660
Weight: 0.02 pounds 0 kg.
TRACK-TYPE TRACTOR,
Information:
TYPE="LEVEL" DEPTH="1" @@@-->Removal Procedure
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Note: The engines are equipped with either an aluminum valve cover or with a composite valve cover. The aluminum valve cover has a seal that fits between the valve cover and the inlet manifold. The composite valve cover has a seal that is permanently fixed to the side of the valve cover.
Illustration 1 g00547002
3054 Engine
Illustration 2 g00572213
3056 Engine
Illustration 3 g00547003
Aluminum valve cover
Illustration 4 g00547004
Composite valve cover
Loosen hose clamp (1) from breather hose (2) .
Disconnect breather hose (2) from valve cover (4) .
Remove three nuts (3), steel washers (6), and sealing washers (8) .Note: When you remove nuts (3), ensure that the nuts on the rocker arm bracket are not loosened.Note: Current production engines have an additional shim washer (7) .
Remove valve cover (4), gasket (10), and seal (5) from the cylinder head.
Remove seal (9) for the oil filler cap.Installation Procedure
Note: The engines are equipped with either an aluminum valve cover or with a composite valve cover. The aluminum valve cover has a seal that fits between the valve cover and the inlet manifold. The composite valve cover has a seal that is permanently fixed to the side of the valve cover.
Illustration 5 g00547002
3054 Engine
Illustration 6 g00572213
3056 Engine
Illustration 7 g00547003
Aluminum valve cover
Illustration 8 g00547004
Composite valve cover
Inspect the condition of the gaskets and the seals. Replace the gaskets and the seals, if necessary.
Install seal (9) for the oil filler cap, if necessary.
Apply 8T-9022 Silicone Gasket to gasket (10) .Note: Ensure that the flat face of the gasket is toward the valve cover.
Install gasket (10), seal (5), and valve cover (4) on the cylinder head.
Lubricate three nuts (3) with clean engine oil.
Install three nuts (3), steel washers (6), and sealing washers (8) .Note: When you install three composite nuts (3) without shim washers (7), tighten the nuts to a torque of 20 N m (15 lb ft). Do not overtighten the nuts.Note: When you install three aluminum nuts (3) with shim washers (7), tighten the nuts to a torque of 30 N m (22 lb ft). Do not overtighten the nuts.
Connect breather hose (2) to valve cover (4) .
Tighten hose clamp (1) on breather hose (2) .
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Note: The engines are equipped with either an aluminum valve cover or with a composite valve cover. The aluminum valve cover has a seal that fits between the valve cover and the inlet manifold. The composite valve cover has a seal that is permanently fixed to the side of the valve cover.
Illustration 1 g00547002
3054 Engine
Illustration 2 g00572213
3056 Engine
Illustration 3 g00547003
Aluminum valve cover
Illustration 4 g00547004
Composite valve cover
Loosen hose clamp (1) from breather hose (2) .
Disconnect breather hose (2) from valve cover (4) .
Remove three nuts (3), steel washers (6), and sealing washers (8) .Note: When you remove nuts (3), ensure that the nuts on the rocker arm bracket are not loosened.Note: Current production engines have an additional shim washer (7) .
Remove valve cover (4), gasket (10), and seal (5) from the cylinder head.
Remove seal (9) for the oil filler cap.Installation Procedure
Note: The engines are equipped with either an aluminum valve cover or with a composite valve cover. The aluminum valve cover has a seal that fits between the valve cover and the inlet manifold. The composite valve cover has a seal that is permanently fixed to the side of the valve cover.
Illustration 5 g00547002
3054 Engine
Illustration 6 g00572213
3056 Engine
Illustration 7 g00547003
Aluminum valve cover
Illustration 8 g00547004
Composite valve cover
Inspect the condition of the gaskets and the seals. Replace the gaskets and the seals, if necessary.
Install seal (9) for the oil filler cap, if necessary.
Apply 8T-9022 Silicone Gasket to gasket (10) .Note: Ensure that the flat face of the gasket is toward the valve cover.
Install gasket (10), seal (5), and valve cover (4) on the cylinder head.
Lubricate three nuts (3) with clean engine oil.
Install three nuts (3), steel washers (6), and sealing washers (8) .Note: When you install three composite nuts (3) without shim washers (7), tighten the nuts to a torque of 20 N m (15 lb ft). Do not overtighten the nuts.Note: When you install three aluminum nuts (3) with shim washers (7), tighten the nuts to a torque of 30 N m (22 lb ft). Do not overtighten the nuts.
Connect breather hose (2) to valve cover (4) .
Tighten hose clamp (1) on breather hose (2) .
Caterpillar SIS machinery equipment:
Caterpillar SIS
D8K TRACTOR / POWER SHIFT / 66V02085-UP (MACHINE) POWERED BY D342 ENGINE »
3S-1660
POWER TAKE-OFF GROUP-REAR
D8K TRACTOR / POWERSHIFT / 77V05006-UP (MACHINE) POWERED BY D342 ENGINE »
3S-1660
POWER TAKE-OFF GP
D8K TRACTOR / DIRECT DRIVE / 76V00505-UP (MACHINE) POWERED BY 342 ENGINE »
3S-1660
POWER TAKE-OFF GP
D8H TRACTOR / POWER SHIFT / 46A24433-UP (MACHINE) »
3S-1660
POWER TAKE-OFF GP
D8H TRACTOR / DIRECT DRIVE / 36A05329-UP (MACHINE) »
3S-1660
POWER TAKE-OFF GP
D342 VEHICULAR ENGINE 76V00001-00504 (MACHINE) »
3S-1660
POWER TAKE-OFF GP
D342 VEHICULAR ENGINE 76V00001-00504 (MACHINE) »
3S-1660
POWER TAKE-OFF GP
Caterpillar parts catalog:
Parts power Caterpillar catalog:
1M0626
POWER TAKE-OFF GP
583K, D8K
583K, D8K
2146957
POWER TRAIN AR
420D, 430D
420D, 430D
9U3364
POWER TAKE-OFF AR
70C, 75C
70C, 75C
9D0300
POWER TRAIN GUARD GROUP
631C, 633C, 637
631C, 633C, 637
1715865
POWER TRAIN AR
CS-431C
CS-431C
3349041
POWER TRAIN AR-OEM
TH35-C11I, TH35-C13I, TH35-C15I, TH35-C15T, TH35-E81
TH35-C11I, TH35-C13I, TH35-C15I, TH35-C15T, TH35-E81
2676804
POWER TRAIN AR
312D, 312D L, 312D2, 312D2 L, 313D
312D, 312D L, 312D2, 312D2 L, 313D
3708554
POWER TRAIN AR-OEM
CX31-C13I, CX31-C15I, CX31-C18I, CX31-P600
CX31-C13I, CX31-C15I, CX31-C18I, CX31-P600