AVSPARE.COM
parts catalog

PRECLEANER 5625850 - Caterpillar


5625850 PRECLEANER Caterpillar parts
Rating:
11
Alternative (cross code) number:
CA5625850
562-5850
5625850
Caterpillar 5625850 PRECLEANER
Weight: 2 pounds 1 kg.

Buy PRECLEANER 5625850 Caterpillar genuine, new aftermarket tractor parts with delivery

Number on catalog scheme: 6
  For full view, you need register

Information:


Illustration 1 g03837436
The remote pressure taps are located underneath the access door directly behind the cab.
(A) Location of remote pressure taps
(B) Enlarged view of transmission
(1) Number 1 clutch
(2) Number 2 clutch
(3) Number 3 clutch
(4) Number 4 clutch
(5) Number 5 clutch
(6) Number 6 clutch
Label both ends of the six hoses that are from the 1U-5482 Pressure Adapter Group. Install each hose assembly from 1U-5482 Pressure Adapter Group onto the pressure tap of the clutch solenoid modulating valve that is being calibrated.
Attach the opposite end of the hose assembly to the 0 to 3400 kPa (0 to 580 psi) pressure gauge in the 1U-5481 Pressure Gauge Group.
Illustration 2 g01093515
STIC Steering Control
(7) Upshift/downshift switch. (8) Transmission direction switch.
Make sure that transmission direction switch (8) is in the NEUTRAL position.
Make sure that the parking brake is engaged.
Start the engine.
Warm the transmission oil to approximately 60 °C (140 °F). Note: The transmission oil temperature gauge should be at the center position.
Start the engine and operate the engine at low idle. Note: If a new clutch solenoid modulating valve was installed, shift the transmission for at least 12 times into a speed or a direction that uses the clutch solenoid modulating valve. Refer to Illustration 1 in order to identify the clutch solenoid modulating valve and the corresponding clutch. Allow sufficient time for the corresponding clutch to be fully pressurized.
Increase the engine speed to high idle. Note: You can use the SET/DECEL switch to maintain the high idle. The RESUME/ACCEL switch can be used to resume high idle.
Table 2
Pressure Specification for Transmission Clutch Engagement
Model Clutch 1 Clutch 2 Clutch 3 Clutch 4 Clutch 5 Clutch 6
834H 2200 70 kPa (320 10 psi) 2200 70 kPa (320 10 psi) 2275 70 kPa (330 10 psi) 2275 70 kPa (330 10 psi) 1725 70 kPa (250 10 psi) 2275 70 kPa (330 10 psi)
836H 2200 70 kPa (320 10 psi) 2200 70 kPa (320 10 psi) - - 1725 70 kPa (250 10 psi) 2275 70 kPa (330 10 psi) Note: The software program that will be used for this test procedure is the Caterpillar Electronic Technician (ET). The Caterpillar Electronic Technician is a software program that can be used on an IBM-compatible personal computer.Reference: For more information about the use of Electronic Technician, refer to Testing and Adjusting, "Using Caterpillar Electronic Technician (ET) to Determine Diagnostic Codes" for the machine that is being serviced.
Illustration 3 g01088159
Typical View
Open the software program (ET). Select the "Transmission 834H" or "Transmission 836H" menu item.
Illustration 4 g01088160
Select the "Service" menu in order to begin the calibration procedure. Then select "Calibrations". A second menu will be displayed. Select "Transmission Clutch Engagement Pressure Calibrations" from the second menu.
Illustration 5 g01081742
Once "Transmission Clutch Engagement Pressure Calibrations" has been selected, the screen displays a dialog box in order to select the clutch or the clutches for

Caterpillar parts catalog:

Caterpillar parts catalog
CX31-P600-C9.3I Transmission Power Train Package GFY00001-UP POWERED BY C9.3 Industrial Engine
C15 Industrial Engine LDN00001-UP
C13 Industrial Engine KWJ00001-UP
CX31-P600-C13I Petroleum Power Train Package KWJ00001-UP
980M Wheel Loader WW300001-UP (MACHINE) POWERED BY C13 Engine
982M Wheel Loader WMD00001-UP (MACHINE) POWERED BY C13 Engine
980M Wheel Loader MK200001-UP (MACHINE) POWERED BY C13 Engine
982M Wheel Loader MK600001-UP (MACHINE) POWERED BY C13 Engine
980M Wheel Loader MGD00001-UP (MACHINE) POWERED BY C13 Engine
982M Wheel Loader LRS00001-UP (MACHINE) POWERED BY C13 Engine
980M Wheel Loader XDJ00001-UP (MACHINE) POWERED BY C13 Engine
982M Wheel Loader XDL00001-UP (MACHINE) POWERED BY C13 Engine
C9.3 Industrial Engine NGH00001-UP
CX31-P600-C9.3I Transmission Power Train Package GFY00001-UP POWERED BY C9.3 Industrial Engine
980K Wheel Loader W7K00001-UP (MACHINE) POWERED BY C13 Engine
980K Wheel Loader GTZ00001-UP (MACHINE) POWERED BY C13 Engine
980M Wheel Loader KRS00001-UP (MACHINE) POWERED BY C13 Engine
980K Wheel Loader High Lift Grapple NEP00001-UP (MACHINE) POWERED BY C13 Engine
982M Wheel Loader K1Y00001-UP (MACHINE) POWERED BY C13 Engine
982M Wheel Loader F9A00001-UP (MACHINE) POWERED BY C13 Engine
980M Wheel Loader N8T00001-UP (MACHINE) POWERED BY C13 Engine
980L Wheel Loader D8Z00001-UP (MACHINE) POWERED BY C13 Engine


Parts precleaner Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.