3179112 PRECOOLER GP Caterpillar parts
C11, C13
Rating:
Alternative (cross code) number:
CA3179112
317-9112
3179112
CA3179112
317-9112
3179112
TRUCK ENGINE,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$33.41
02 Oct 2021
US: WLSupply
J3179112 J3227854 3179112 8126762 Valve Cover Gaskets Compatible with Jeep
Sawyer Auto Same quality as OE for less money || Designed with the latest software and manufactured with modern tooling || Direct fit replacement || Installs the same as factory unit || Same dimensions as OE part
Sawyer Auto Same quality as OE for less money || Designed with the latest software and manufactured with modern tooling || Direct fit replacement || Installs the same as factory unit || Same dimensions as OE part
Number on catalog scheme:
For full view, you need register
Information:
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Guide Studs
(M8 by 70 mm) 2
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Ensure that the water pump is clean and free from wear or damage. If necessary, replace the water pump.
Illustration 1 g02717775
If necessary, install the cover to the water pump . Follow Steps 2.a through 2.d in order to install the cover.
Clean the gasket surface of cover (7).
Position a new gasket (6) (not shown) on water pump (3).
Install cover (7) to water pump (3).
Install bolts (9) to cover (7). Tighten bolts finger tight.
Illustration 2 g02721481
Clean the gasket surface of front cover (1).
Install Tooling (A) in Position (X).
Use Tooling (A) in order to align new gasket (2) to front cover (1). Install the gasket to the front cover.
Align water pump (3) to Tooling (A). Install the water pump to front cover (1). Note: Ensure that the gear of the water pump and the gear of the fuel injection pump mesh.
Illustration 3 g02721493
Bolts (9) for cover plate.
(5) M8 by 30 mm
(4) M8 by 75 mm
(8) M8 by 65 mm
Illustration 4 g02721495
Install bolts (4), bolts (5), and bolts (8). Refer to Illustration 3. Tighten the bolts finger tight. Note: Ensure that all bolts of different lengths are installed in the correct positions.
Remove Tooling (A) and install remaining bolts (4).
Tighten bolts (4), bolts (5), bolts (8), and bolts (9) in the sequence that is shown in Illustration 4 to a torque of 22 N m (195 lb in).
Install the hose to the water pump inlet. Tighten the hose clamps securely.
Fill the cooling system with coolant. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change" for the correct procedure. End By:
Install the fan and the fan pulley. Refer to Disassembly and Assembly, "Fan - Remove and Install".
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Guide Studs
(M8 by 70 mm) 2
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Ensure that the water pump is clean and free from wear or damage. If necessary, replace the water pump.
Illustration 1 g02717775
If necessary, install the cover to the water pump . Follow Steps 2.a through 2.d in order to install the cover.
Clean the gasket surface of cover (7).
Position a new gasket (6) (not shown) on water pump (3).
Install cover (7) to water pump (3).
Install bolts (9) to cover (7). Tighten bolts finger tight.
Illustration 2 g02721481
Clean the gasket surface of front cover (1).
Install Tooling (A) in Position (X).
Use Tooling (A) in order to align new gasket (2) to front cover (1). Install the gasket to the front cover.
Align water pump (3) to Tooling (A). Install the water pump to front cover (1). Note: Ensure that the gear of the water pump and the gear of the fuel injection pump mesh.
Illustration 3 g02721493
Bolts (9) for cover plate.
(5) M8 by 30 mm
(4) M8 by 75 mm
(8) M8 by 65 mm
Illustration 4 g02721495
Install bolts (4), bolts (5), and bolts (8). Refer to Illustration 3. Tighten the bolts finger tight. Note: Ensure that all bolts of different lengths are installed in the correct positions.
Remove Tooling (A) and install remaining bolts (4).
Tighten bolts (4), bolts (5), bolts (8), and bolts (9) in the sequence that is shown in Illustration 4 to a torque of 22 N m (195 lb in).
Install the hose to the water pump inlet. Tighten the hose clamps securely.
Fill the cooling system with coolant. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change" for the correct procedure. End By:
Install the fan and the fan pulley. Refer to Disassembly and Assembly, "Fan - Remove and Install".
Caterpillar SIS machinery equipment:
Caterpillar parts catalog:
Parts precooler Caterpillar catalog:
2276756
PRECOOLER GP
C11, C13
C11, C13
C11, C13
2276755
PRECOOLER GP
C11, C13
C11, C13
2276755
PRECOOLER GP
C11, C13
C11, C13
C11, C13
2276756
PRECOOLER GP
C11, C13
C11, C13
2729889
PRECOOLER GP
C15, TH35-C15T
C15, TH35-C15T
2919708
PRECOOLER GP
C9, TH31-E61
C9, TH31-E61
2937886
PRECOOLER GP
C13, TH35-C13T
C13, TH35-C13T
2937885
PRECOOLER GP
C13, TH35-C13T
C13, TH35-C13T
2877219
PRECOOLER GP
C13, TH35-C13T
C13, TH35-C13T
2877218
PRECOOLER GP
C13, TH35-C13T
C13, TH35-C13T
2729808
PRECOOLER GP
C13, TH35-C13T
C13, TH35-C13T
2729806
PRECOOLER GP
C13, TH35-C13T
C13, TH35-C13T