AVSPARE.COM
parts catalog

PRESSURIZER GP-CAB 2878875 - Caterpillar



2878875 PRESSURIZER GP-CAB Caterpillar parts AD30, AD45B, AD55, AD55B, AD60, R1300G, R1300G II, R1600G, R1600H, R1700G, R2900G, R3000H PRESSURIZER
Rating:
23
Alternative (cross code) number:
CA2878875
287-8875
2878875
Caterpillar 2878875 PRESSURIZER GP-CAB
Weight: 29 pounds 13 kg.

Buy PRESSURIZER GP-CAB 2878875 Caterpillar genuine, new aftermarket tractor parts with delivery
LOAD HAUL DUMP, UNDERGROUND ART TRUCK,

Compatible equipment models: 2878875:

LOAD HAUL DUMP  R1300G   R1300G II   R1600G   R1600H   R1700G   R2900G   R3000H  
UNDERGROUND ART TRUCK  AD30   AD45B   AD55   AD55B   AD60   Caterpillar
Number on catalog scheme: 10
 
  For full view, you need register

Information:


Illustration 1 g00602453
Schematic of the Position Sensor (Inching Pedal)
This diagnostic code is for the Position Sensor (Inching Pedal).This diagnostic code is recorded when the signal for the inching pedal position sensor is out of range. The possible causes for this diagnostic code are listed below:
The +Battery circuit from the electrical system to the sensor is open.
The return circuit (G939-PK(Pink)) is open.
The signal circuit (F843-YL(Yellow)) is shorted to +battery or shorted to ground.
The signal circuit (F843-YL(Yellow)) is open or the sensor is disconnected.
The sensor linkage is broken.
The sensor has failed.
The ECM has failed. This is unlikely. System Response:Note: Ensure that the CID 0573 FMI 08 is on hold and that the diagnostic code indicator shows "SERV CODE". This procedure can cause new diagnostic codes to be recorded. Ignore these created problems. When the procedure is completed, clear the created problems. Test Step 1. CHECK THE OPERATION OF THE SENSOR.
Turn the key start switch to the ON position.
Testing and Adjusting, "Using Caterpillar Monitoring System to Determine Diagnostic Codes".
Disconnect the machine harness from the sensor. Observe and note the value that is showing for the sensor signal.
At the machine harness, place a jumper from contact 2 (the return circuit) to contact 3 (signal). Observe and note the value that is showing for the sensor signal. Expected Result:The value that is displayed should change from "100" to "000" when the jumper is installed.Results:
OK - The value changed from "100" to "000" when the jumper was installed.Repair: The machine harness and the ECM are operating properly. The sensor has failed. Check the mechanical assembly of the sensor. Ensure that the sensor is moving properly when the inching pedal is pressed and released. If there is no problem with the mechanical assembly of the sensor, replace the inching pedal position sensor.STOP
NOT OK - The value did not change from "100" to "000" when the jumper was installed. The machine harness or the ECM may have failed. Proceed to Test Step 2.Test Step 2. CHECK THE +BATTERY CIRCUIT AT THE SENSOR.
The key start switch remains ON. The machine harness remains disconnected from the sensor.
At the machine harness for the sensor, measure the voltage (VDC) between contact 1 (+Battery) and frame ground. Expected Result:The voltage should measure 9.0 VDC to 32 VDC.Results:
OK - The voltage measures 9.0 VDC to 32 VDC. The +battery

Caterpillar SIS machinery equipment:

Caterpillar SIS

Caterpillar parts catalog:

Caterpillar parts catalog
R1300G Underground Mining LJB00001-UP (MACHINE) POWERED BY 3306 Engine
R1300G Series II Load Haul Dump RSL00001-UP (MACHINE) POWERED BY C6.6 Engine
R2900G Load Haul Dump JLK00001-UP (MACHINE) POWERED BY C15 Engine
R1700G Load Haul Dump SBR00001-UP (MACHINE) POWERED BY C11 Engine
R1600G Load Haul Dump 9YZ00001-UP (MACHINE) POWERED BY 3176C Engine
R3000H Load Haul Dump RCM00001-UP (MACHINE) POWERED BY C15 Engine
R1600H Load Haul Dump 9SD00001-UP (MACHINE) POWERED BY C11 Engine
R1300G Load Haul Dump NJB00001-UP (MACHINE) POWERED BY 3306 Engine
R1700G Load Haul Dump XBR00001-UP (MACHINE) POWERED BY C11 Engine
R2900G Swivel Seat Supplemental JLK00001-UP (MACHINE)
AD55 Underground Articulated Truck DNW00001-UP (MACHINE) POWERED BY C18 Engine
AD45B Underground Articulated Truck CXM00001-UP (MACHINE) POWERED BY C18 Engine
AD30 Underground Articulated Truck DXR00001-UP (MACHINE) POWERED BY C15 Engine
AD55B Underground Articulated Truck JNW00001-UP (MACHINE) POWERED BY C27 Engine
AD60 Articulated Underground Truck KNW00001-UP (MACHINE) POWERED BY C27 Engine


Parts pressurizer Caterpillar catalog:

1605593 PRESSURIZER & MOUNTING GP
R1600, R1600G, R1600H, R1700G
1560525 PRESSURIZER GP
R1300, R1300G, R1300G II
3354815 PRESSURIZER GP-CAB
AD30, AD45B, AD55, AD55B, AD60, R1300G, R1300G II, R1600G, R1600H, R1700G, R2900G, R3000H
1605592 PRESSURIZER GP
R1600, R1600G, R1600H, R1700G
3354816 PRESSURIZER GP-CAB
AD30, AD45B, AD55, AD55B, AD60, R1300G, R1300G II, R1600G, R1600H, R1700G, R2900G, R3000H
5G2002 PRESSURIZER GP
931B, 931C, 931C II, 935B, 935C, 935C II, D3B, D3C, D3C II, D4B, D4C, D4C II, D5C
3354815 PRESSURIZER GP-CAB
AD30, AD45B, AD55, AD55B, AD60, R1300G, R1300G II, R1600G, R1600H, R1700G, R2900G, R3000H
1560525 PRESSURIZER GP
R1300, R1300G, R1300G II
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.