AVSPARE.COM
parts catalog

PRESSURIZER GP-CAB 5088564 - Caterpillar



5088564 PRESSURIZER GP-CAB Caterpillar parts PRESSURIZER
Rating:
21
Alternative (cross code) number:
CA5088564
508-8564
5088564
Caterpillar 5088564 PRESSURIZER GP-CAB
Weight: 11 pounds 5 kg.

Buy PRESSURIZER GP-CAB 5088564 Caterpillar genuine, new aftermarket tractor parts with delivery

Number on catalog scheme: 5
 
  For full view, you need register

Information:

Bolts And Bolt Torque
A bolt which is too long may "bottom" before the head is tight against the part it is to hold. The threads can be damaged when a "long" bolt is removed.If a bolt is too short, there may not be enough threads engaged to hold the part securely.Apply proper torque values to all bolts and nuts when assembling Caterpillar equipment. When a specific torque value is required, the value is listed in the SPECIFICATIONS section of the Service Manual. Tighten all other bolts and nuts for general usage, hydraulic valve bodies, or taperlock studs to the torque values given in the torque charts.T-T-T Procedure
A torque-turn-tighten (T-T-T) procedure is used in many specifications and instructions.1. Clean the bolt and nut threads.2. Put lubricant on the threads and the seat face of the bolt and the nut.3. Turn the bolt or the nut tight according to the torque specification.4. Put a location mark on the part and on the bolt or the nut.5. Turn the bolt or the nut tighter the amount of degrees according to the specifications. The side of a nut or bolt head can be used for reference if a mark can not be put on. Torque Wrench Extension
When a torque wrench extension is used with a torque wrench, the torque indication on the torque wrench will be less than the real torque.
TORQUE WRENCH WITH TORQUE WRENCH EXTENSION
E: Torque wrench drive axis-to-torque wrench extension drive axis. W: Mark on handle-to-torque wrench drive axis.1. Put a mark on the handle. Measure the handle from the mark to the axis of the torque wrench drive (W).2. Measure the torque wrench extension from the torque wrench drive to the axis of the torque wrench extension drive (E).3. To get correct torque indication (TI) when the real torque (RT) is known: Example: W = 12 in. (304.8 mm); E = 2.56 in. (65.0 mm); RT (from specifications) = 125 lb. ft. (170 N m). 4. Hold the torque wrench handle with the longest finger of the hand over the mark on the handle to get the real torque (RT) with low torque indication (TI) on the torque wrench.Locks
Flat metal locks must be installed properly to be effective. Bend one end of the lock around the edge of the part. Bend the other end against one flat surface of the nut or bolt head.Always install new locks in compartments which house moving parts.If lockwashers are installed on housings made of aluminum, use a flat washer between the lockwasher and the housing. Lines And Wires
When removing or disconnecting a group of lines or wires, tag each one to assure proper assembly.Lubrication
Where applicable, fill the compartments of the components serviced with the amount, type and grade of lubricant recommended in the Lubrication and Maintenance Guide.Rust Preventive Compound
Clean the rust preventive compound from all machined surfaces of new parts before installing them.Shims
When shims are removed, tie them together and identify them as to location. Keep shims clean and flat until they are

Caterpillar SIS machinery equipment:

Caterpillar SIS

Caterpillar parts catalog:

Caterpillar parts catalog
R1300G Underground Mining LJB00001-UP (MACHINE) POWERED BY 3306 Engine
R1300G Series II Load Haul Dump RSL00001-UP (MACHINE) POWERED BY C6.6 Engine
R2900G Load Haul Dump JLK00001-UP (MACHINE) POWERED BY C15 Engine
R1700G Load Haul Dump SBR00001-UP (MACHINE) POWERED BY C11 Engine
R1600G Load Haul Dump 9YZ00001-UP (MACHINE) POWERED BY 3176C Engine
R1300G Load Haul Dump NJB00001-UP (MACHINE) POWERED BY 3306 Engine
R1700G Load Haul Dump XBR00001-UP (MACHINE) POWERED BY C11 Engine
AD55 Underground Articulated Truck DNW00001-UP (MACHINE) POWERED BY C18 Engine
AD45B Underground Articulated Truck CXM00001-UP (MACHINE) POWERED BY C18 Engine
AD30 Underground Articulated Truck DXR00001-UP (MACHINE) POWERED BY C15 Engine
AD55B Underground Articulated Truck JNW00001-UP (MACHINE) POWERED BY C27 Engine


Parts pressurizer Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.