AVSPARE.COM
parts catalog

PROTECTION GP 2500968 - Caterpillar



2500968 PROTECTION GP Caterpillar parts R1700G, R2900G, R3000H PROTECTION
Rating:
83
Alternative (cross code) number:
CA2500968
250-0968
2500968
Caterpillar 2500968 PROTECTION GP

Buy PROTECTION GP 2500968 Caterpillar genuine, new aftermarket tractor parts with delivery
LOAD HAUL DUMP,

Compatible equipment models: 2500968:

LOAD HAUL DUMP  R1700G   R2900G   R3000H   Caterpillar
Number on catalog scheme:
 
  For full view, you need register

Information:

Removal Procedure
Start By:
Remove the mounting bracket. Refer to Service Manual, "Mounting Bracket - Remove and Install".
Hot oil and components can cause personal injury.Do not allow hot oil or components to contact skin.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before operating any compartment or disassembling any component containing fluids.After collecting all fluids in suitable containers, dispose of all fluids according to local regulations and mandates.
Illustration 1 g00749219
Position the work tool in an upright position, as shown. The work tool should only be positioned in this manner on a solid, level surface. If a solid level surface is not available, lay the work tool on a side.
Put identification marks on all hoses for installation purposes. Plug all hoses in order to help prevent fluid loss and contamination of the fluid system.
Illustration 2 g00706335
Remove two bolts (1) and the washers that secure coupling (2). Repeat this step for the other coupling.
Illustration 3 g00706710
Disconnect two lines (3) from swivel (4). Note the stampings near the inlet ports on the swivel. The O stamping is for the circuit that retracts the cylinder. The B stamping is for the circuit that extends the cylinder. The ports should be installed with the same orientation.
Illustration 4 g00706712
Remove two bolts and the washers that secure lock (5) to the lower housing. Remove the lock.
Remove the six bolts and the washers that secure lock plate (6) to the swivel. Remove the plate from the work tool.
Illustration 5 g00706718
Remove the eight bolts, the washers, and the four half flanges that secure two hose assemblies (7) to swivel (4). Remove the O-ring seals from the hoses.
Illustration 6 g00706724
Attach an appropriate nylon lifting sling and a hoist to swivel (4). The weight of the swivel is 43 kg (95 lb).
Remove the six bolts and the washers that secure ring (8) to the upper housing. Remove the swivel from the work tool.
Illustration 7 g00707712
Remove two adapters (9). Remove the seal and the O-ring seal from each adapter.
Remove the six bolts and the washers that secure ring (8) to the swivel. Remove the ring from the swivel.

Caterpillar SIS machinery equipment:

Caterpillar SIS


Parts protection Caterpillar catalog:

3001887 PROTECTION AR-CORROSION
924G, 924H, 924HZ, 928HZ, IT28G
2898463 PROTECTION GP-VANDALISM
950H, 962H, 966H, 972H, 980H
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.