AVSPARE.COM
parts catalog

PROTECTOR-EDGE 3236395 - Caterpillar



3236395 PROTECTOR-EDGE Caterpillar parts PROTECTOR
Rating:
31
Alternative (cross code) number:
CA3236395
323-6395
3236395
Caterpillar 3236395 PROTECTOR-EDGE

Buy PROTECTOR-EDGE 3236395 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:


Illustration 9 g00562408
Remove sleeve bearings (11) from oil pump manifold (1).Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Gp 1 Note: Cleanliness is an important factor. Before assembly, thoroughly clean all parts in cleaning fluid. Allow the parts to air dry. Do not use wiping cloths or rags to dry parts. Lint may be deposited on the parts which may cause trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement. Dirt and other contaminants can damage the precision component. Perform assembly procedures on a clean work surface. Keep components covered and protected always.Note: Check the O-ring seals for wear or for damage. Replace the components, if necessary.
Make sure that all parts are thoroughly clean prior to assembly. Apply clean SAE 30W oil to all parts.
Illustration 10 g00562408
Illustration 11 g00844395
The correct assembled height of the locating dowels is 5 0.5 mm (.197 .020 inch).
Use Tooling (A) to install sleeve bearings (11) into oil pump manifold (1). Install sleeve bearings (11) into the bores so that sleeve bearings (11) are 1.5 0.5 mm (.06 .02 inch) below the surface of oil pump manifold (1). Install sleeve bearings (11) so that the joints of sleeve bearings (11) are 30 15 degrees from the centerlines of the shafts, as shown.
Illustration 12 g00439426
Install oil pump body assembly (10) to oil pump manifold (1).
Illustration 13 g06288722
Install gear assemblies (8) and (9) to oil pump manifold (1).
Illustration 14 g00439327
Illustration 15 g00439763
Use Tooling (A) to install sleeve bearings (7) in oil pump cover assembly (6). Install sleeve bearings (7) into the bores so that sleeve bearings (7) are 1.50 0.25 mm (0.059 0.01 inch) below the surface of oil pump cover assembly (6). Install sleeve bearings (7) so that the joints of sleeve bearings (7) are 30 15 degrees from the centerlines of the shafts, as shown.
Illustration 16 g06288721
Install oil pump cover assembly (6) and bolts (5).
Illustration 17 g00439267
Install O-ring seal (4) onto temperature sensor (2).
Illustration 18 g06288720
Install O-ring seal (3). Install temperature sensor (2) to oil pump manifold (1).The pump must rotate freely by hand.End By:
Install the transmission oil pump.Installation Procedure
Illustration 19 g01325108
Attach a suitable lifting device to transmission oil pump (1). The weight of transmission oil pump (1) is approximately 30 kg (66 lb).
Use the suitable lifting device to position transmission oil pump (1) to the machine.
Install bolt (7) and bolts (8).
Illustration 20 g06288729
Connect temperature sensor (6). Attach harness assembly (2) to transmission oil pump (1).
Connect hose assembly (4) and install bolts (3).
Connect tube assembly (5) and install the bolts.End By:
Install the piston pump (steering).


Parts protector Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.