2S4234 PULLEY Caterpillar parts
D8H
Rating:
Alternative (cross code) number:
CA2S4234
2S-4234
2S4234
CA2S4234
2S-4234
2S4234
Weight: 11 pounds 4 kg.
TRACK-TYPE TRACTOR,
Compatible equipment models: 2S4234:
Information:
Battery Life and Recommended Practices
Battery life is very difficult to predict and can vary greatly based on a number of factors including:
Battery age
Machine configuration
Engine starting frequency
Ambient conditions
Storage practicesThere are a number of components that draw small amounts of electrical current even when the key switch is OFF. Some of these include:
Electronic control modules for the machine, engine, emissions system, etc
Radios or displays with memory features
Product Link or other GPS-based systemsIt is recommended to start and operate your machine normally for at least 15 minutes every few weeks to prevent battery discharge which may damage the battery beyond simple recharge. This time should be extended during the winter as the load on the battery increase with extended heater usage, heated seat usage, and typically increased usage of the work lights.The use of a battery disconnect switch or disconnection of the battery cables is recommended if the machine will sit longer than a few weeks under normal conditions. The use of a battery disconnect switch may be advisable at the end of each working day in extreme ambient conditions.Additional references:
"Operation and Maintenance Manual" , Machine Storage Procedure
"Operation and Maintenance Manual" , DEF Guidelines
"Operation and Maintenance Manual" , Battery Disconnect Switch
"Operation and Maintenance Manual" , Engine StartingInspect / Replace
Turn the engine start switch to the OFF position. Turn all switches to the OFF position.
The battery is located in the engine compartment and may either be on the left-hand side or right-hand side. Open the engine access door.
Disconnect the negative battery cable at the battery.Note: Do not allow the disconnected battery cable to contact the negative battery post.
Disconnect the negative battery cable from the frame in order to inspect the cable.
Disconnect the positive battery cable at the battery.
Perform the necessary repairs. Replace the cables or the battery, as needed.
Connect the positive battery cable at the battery.
Connect the negative battery cable to the frame of the machine.
Connect the negative battery cable at the battery.
Close the engine access door.Recycle the Battery
Always recycle a battery. Never discard a battery.Always return used batteries to one of the following locations:
A battery supplier
An authorized battery collection facility
Recycling facility
Battery life is very difficult to predict and can vary greatly based on a number of factors including:
Battery age
Machine configuration
Engine starting frequency
Ambient conditions
Storage practicesThere are a number of components that draw small amounts of electrical current even when the key switch is OFF. Some of these include:
Electronic control modules for the machine, engine, emissions system, etc
Radios or displays with memory features
Product Link or other GPS-based systemsIt is recommended to start and operate your machine normally for at least 15 minutes every few weeks to prevent battery discharge which may damage the battery beyond simple recharge. This time should be extended during the winter as the load on the battery increase with extended heater usage, heated seat usage, and typically increased usage of the work lights.The use of a battery disconnect switch or disconnection of the battery cables is recommended if the machine will sit longer than a few weeks under normal conditions. The use of a battery disconnect switch may be advisable at the end of each working day in extreme ambient conditions.Additional references:
"Operation and Maintenance Manual" , Machine Storage Procedure
"Operation and Maintenance Manual" , DEF Guidelines
"Operation and Maintenance Manual" , Battery Disconnect Switch
"Operation and Maintenance Manual" , Engine StartingInspect / Replace
Turn the engine start switch to the OFF position. Turn all switches to the OFF position.
The battery is located in the engine compartment and may either be on the left-hand side or right-hand side. Open the engine access door.
Disconnect the negative battery cable at the battery.Note: Do not allow the disconnected battery cable to contact the negative battery post.
Disconnect the negative battery cable from the frame in order to inspect the cable.
Disconnect the positive battery cable at the battery.
Perform the necessary repairs. Replace the cables or the battery, as needed.
Connect the positive battery cable at the battery.
Connect the negative battery cable to the frame of the machine.
Connect the negative battery cable at the battery.
Close the engine access door.Recycle the Battery
Always recycle a battery. Never discard a battery.Always return used batteries to one of the following locations:
A battery supplier
An authorized battery collection facility
Recycling facility
Caterpillar parts catalog:
Parts pulley Caterpillar catalog:
1S4701
PULLEY
16, 769, 834, 977H, 980, D8H
16, 769, 834, 977H, 980, D8H
3P0163
PULLEY
D8H
D8H
3S7517
PULLEY
D8H
D8H
3S7519
PULLEY
D8H
D8H
2S5201
PULLEY
D8H
D8H
2S8892
PULLEY
D8H
D8H
5S1264
PULLEY
D8H
D8H
3S5081
PULLEY
D8H
D8H
3S5081
PULLEY
D8H
D8H
5S9519
PULLEY
D8H
D8H
6N4601
PULLEY-FAN DRIVE
120G, 12G, 130G, 140G
120G, 12G, 130G, 140G
2056784
PULLEY-FAN
330C, 330C L, 330C MH
330C, 330C L, 330C MH
2273810
PULLEY-FAN
330C, 330C FM, 330C L, 330C MH
330C, 330C FM, 330C L, 330C MH
3P0165
PULLEY-FAN DRIVE
120G, 12G, 130G, 140G, 14G, 160G
120G, 12G, 130G, 140G, 14G, 160G
1857451
PULLEY
D7R II
D7R II
2S8870
PULLEY
D8H
D8H