5R1181 PULLEY-CRANKSHAFT Caterpillar parts
D7F
Rating:
Alternative (cross code) number:
CA5R1181
5R-1181
5R1181
CA5R1181
5R-1181
5R1181
Weight: 30 pounds 13 kg.
TRACK-TYPE TRACTOR,
Compatible equipment models: 5R1181:
Number on catalog scheme:
8
For full view, you need register
Information:
Removal Procedure
Start By:
Release the hydraulic system pressure.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.Dispose of all fluids according to local regulations and mandates.
Personal injury can result from hydraulic oil pressure and hot oil.Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system.Make sure all of the work tools have been lowered to the ground, and the oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.
Drain the hydraulic fluid into a suitable container for storage or disposal. Refer to Operation and Maintenance Manual, ""Hydraulic System Oil – Change"" for the correct draining and filling procedures.
Illustration 1 g03527991
Remove bottom plate (1).
Illustration 2 g03527990
Open hood (2). Remove panel (3).
Illustration 3 g06306176
Disconnect and reposition hose (4).
Illustration 4 g06306177
Remove bolts (7) and (5). Remove cover (6).
Illustration 5 g06306195
Remove bolts (9) and disconnect tube assembly (8).
Remove bolts (10) and disconnect tube assembly (11).
Remove bolts (12) and disconnect tube assembly (13).
Illustration 6 g06306197
Disconnect hose assemblies (16) and (17). Remove bolts (14) and check valve (cooler bypass) (15).Installation Procedure
Install the check valve (cooler bypass) in the reverse order of removal.
Tighten bolts (14) to a torque of 55 10 N.m (41 7 lb ft).
Tighten bolts (12), (10), and (9) to a torque of 50 10 N.m (37 7 lb ft).
Start By:
Release the hydraulic system pressure.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.Dispose of all fluids according to local regulations and mandates.
Personal injury can result from hydraulic oil pressure and hot oil.Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system.Make sure all of the work tools have been lowered to the ground, and the oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.
Drain the hydraulic fluid into a suitable container for storage or disposal. Refer to Operation and Maintenance Manual, ""Hydraulic System Oil – Change"" for the correct draining and filling procedures.
Illustration 1 g03527991
Remove bottom plate (1).
Illustration 2 g03527990
Open hood (2). Remove panel (3).
Illustration 3 g06306176
Disconnect and reposition hose (4).
Illustration 4 g06306177
Remove bolts (7) and (5). Remove cover (6).
Illustration 5 g06306195
Remove bolts (9) and disconnect tube assembly (8).
Remove bolts (10) and disconnect tube assembly (11).
Remove bolts (12) and disconnect tube assembly (13).
Illustration 6 g06306197
Disconnect hose assemblies (16) and (17). Remove bolts (14) and check valve (cooler bypass) (15).Installation Procedure
Install the check valve (cooler bypass) in the reverse order of removal.
Tighten bolts (14) to a torque of 55 10 N.m (41 7 lb ft).
Tighten bolts (12), (10), and (9) to a torque of 50 10 N.m (37 7 lb ft).
Caterpillar parts catalog:
Parts pulley Caterpillar catalog:
120, 120G, 12F, 12G, 130G, 140, 140G, 14E, 14G, 160G, 215, 215B, 225, 235, 330, 330 FM L, 330 L, 330B, 330B L, 515, 518, 518C, 525, 528B, 530B, 627B, 814, 815, 816, 920, 930, 941, 950, 951B, 955K, 955...
814, 966C, D7F
9S6123
PULLEY
D7F
D7F
2P5629
PULLEY
D7F
D7F
216, 216B, 226B, 232B, 242B, 247B, 257B, 3013C, 3024, 3024C, 3054C, 3054E, C1.5, C2.2, C3.3, CB-214E, CB-334E
216, 236, 236B, 236B3, 242B3, 246C, 247, 252B, 252B3, 256C, 257B3, 259B3, 262C, 262C2, 267, 267B, 268B, 272C, 277C, 277C2, 279C, 279C2, 287, 287C, 287C2, 289C, 289C2, 297C, 299C, 3044C, 904B, 904H, 90...
216, 228, 236, 247, 248, 267, 287, 3034, 906
1541822
PULLEY-WATER PUMP
216, 216B, 216B3, 226B, 226B3, 232B, 242B, 247B, 247B3, 257B, 3013, 3013C, 3014, 302.5, 3024, 3024C, 902, AP-255E, BB-621C, C1.5, C2.2, CB-214D, CB-214E, CB-334D, CB-334E, CB-335D, CB-34
216, 216B, 216B3, 226B, 226B3, 232B, 242B, 247B, 247B3, 257B, 3013, 3013C, 3014, 302.5, 3024, 3024C, 902, AP-255E, BB-621C, C1.5, C2.2, CB-214D, CB-214E, CB-334D, CB-334E, CB-335D, CB-34
2014118
PULLEY-FAN
C9, MTC735
C9, MTC735
120H, 12H, 135H, 140H, 143H, 14H, 160H, 163H, 16H, 3126, 3126B, 3126E, 3176C, 3196, 3406E, 345B, 345B II, 345B II MH, 345B L, 365B, 365B II, 365B L, 385B, 5090B, 584, 725, 730, 938G II, 938H, 950G II,...
120M 2, 3176C, 3196, 3406E, 345B, 345B II, 345B II MH, 345B L, 365B, 365B II, 365B L, 365C, 365C L, 365C L MH, 374D L, 385B, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 5090B, 621B, 621G, 623G, 62...
1923835
PULLEY
MTC735
MTC735
140G, 140M, 140M 2, 160M, 160M 2, 2290, 2390, 2391, 2491, 2590, 3126B, 322C, 322C FM, 324D, 324D FM, 324D FM LL, 324D L, 324D LN, 325C, 325C FM, 325D, 325D FM, 325D FM LL, 325D L, 325D MH, 326D L, 328...
D7F