PULLEY 7M0239 - Caterpillar

Illustration 4 g02599900
Gusset plate for outboard side (8) 2 plates per machine.
(W) 92 mm (3.62 inch)
(X) 10 mm (0.39 inch)
(Y) 195 mm (7.68 inch)
(Z) 40 mm (1.57 inch) radius on 2 ends of the plate.
(AA) 745 mm (29.33 inch)
(AB) 15 mm (0.59 inch) on both end of the plate.
(AC) 110 mm (4.33 inch)
Illustration 5 g02601056
Gusset plate for inboard side (9) 1 plate per machine. Plate (9) and (10) have same dimensions but different bevel.
Illustration 6 g02601241
Gusset plate for inboard side (10) 1 plate per machine. Plate (9) and (10) have same dimensions but different bevel.
(AD) 16 mm (0.63 inch)
(AE) 12 mm (0.47 inch) with a 45 degree bevel edge.
(AF) 327.2 mm (12.88 inch)
(AG) 220.2 mm (8.67 inch)
(AH) 53.3 mm (2.10 inch)
(AJ) 170 mm (6.69 inch)
(AK) 15 mm (0.59 inch) radius in 6 places.
(AL) 56.5 mm (2.22 inch)
(AM) 30 mm (1.18 inch)radius.
(AN) 4.9 mm (0.19 inch)
(AP) 15 mm (0.59 inch)
(AR) 139 mm (5.47 inch)
(AS) 222 mm (8.74 inch)
(AT) 102 mm (4.02 inch)
(AU) 118 mm (4.65 inch) radius.
(AV) 32 mm (1.26 inch) radius.Reinforce the Track Roller Frame
Required Parts ( Fabrication of Plates)
Preparing the Metal for Welding
Track Roller Frame Reinforcement ProcessPreparing the Metal for Welding
Personal injury can result from flame cutting or welding on painted areas.The effect of gasses from burned paint is a hazard to the person doing the cutting or welding.Do not flame cut or weld on painted areas.
Cover all finished bores and threads. Finished bores and threads must be protected from shot blasting, welding, and paint spatters.All grease, water, paint, rust, dirt, and scale must be removed before welding. Any of these materials will discharge gas which will cause porosity in the weld deposit. Water and rust will cause hydrogen embrittlement. Hydrogen embrittlement causes cracks in the weld deposit.Remove paint, rust, dirt, and scale with a wire brush or by buffing or grinding. Shot blasting all work areas can also remove foreign material.Track Roller Frame Reinforcement Process
Note: All welds are 1.5 mm (0.06 inch) penetration, and a 6 mm (0.24 inch) fillet over square groove (W1) or bevel groove (W2).
Illustration 7 g02601276
(6) Ribs for outboard side
(AW) Plate
(AX) Plate
(AY) Dimension 125 mm (4.92 inch)
Locate outboard rib plates (6) on frame rail as shown in Illustration 7 using dimension (AY). Align top rib with plate (AW) as shown in Illustration 7. Align bottom rib with plate (AX) as shown in Illustration 7.
Weld each outboard rib on both sides and all around
Illustration 8 g02601541
(6) Ribs for outboard side
(7) Box plate
Locate Box plate (7) on straight edges of the ribs (6) as shown in Illustration 8.
Weld top of box plate (7) to outboard top rib (6). Weld bottom of box plate (7) to outboard bottom rib (6).
Illustration 9 g02601618
(8) Gusset plate for outboard side
Locate gusset plate (8) as shown in Illustration 9. Align front edge with front edge of top and bottom outboard ribs as seen by the arrows.
Weld gusset plate (8) to box plate (7).
Weld gusset plate (8) to bottom of track roller frame.
Illustration 10 g02601784
Locate inboard plate (9) and (10) on frame rail as shown in Illustration